Russound DPA-6.12 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

DPA-6.12
Instruction Manual
12 Channel Amplifier
6 Z ONE — 12 C HANNEL A MPLIFIER
123 4 56
POWER ZONE
DPA-6.12

ملخص المحتوى في الصفحة رقم 2

14. Non-use Periods - The power cord of the appliance should be 1. SAFETY INSTRUCTIONS unplugged from the outlet when left unused for a long period of time. 15. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through the open- ings. 16. Damage Requiring Service - The appliance should be serviced by qualified service personnel when: “WARNING” “ TO REDUCE THE RISK OF FIRE OR A. The power - supply cord or the plug has been da

ملخص المحتوى في الصفحة رقم 3

2. INTRODUCTION Congratulations on your recent purchase of the Russound DPA-6.12 12-channel amplifier. The DPA-6.12 high- current, high-quality amplifier is the heart of the home theater or multi-zone system. The DPA-6.12 12-channel amplifier is capable of amplifying six stereo line level sources (CD players, tape decks, preamplifiers, tuners, etc.) simultaneously in multi-zone, multi-source installations. The twelve amplifiers are arranged in pairs to provide six stereo amplifiers. With separat

ملخص المحتوى في الصفحة رقم 4

4. FRONT PANEL Rack Mounting: The DPA-6.12 amplifier can be rack mounted. The amplifier will take four rack spaces. Power Switch: Turns on the main power for the amplifier. When the power is on the LED will be illuminated. Zone Indicator LEDs: Zone one to six will be illuminated when the zone is in the active mode. When the zone is mute or inactive the LED will not be illuminated. 6 Z ONE — 12 C HANNEL A MPLIFIER 123 4 56 POWER ZONE DPA-6.12 MAIN BUS INPUT R L R 5. BACK PANEL CONNECTIONS Main

ملخص المحتوى في الصفحة رقم 5

Speaker Outputs: The A and B speaker outputs are in parallel to the amplifier output. When connected to the A or B output either 4-ohm or 8-ohm speakers could be connected. When using both A and B speaker outputs, only 8- ohm speakers can be connected, and this will result in a 4-ohm load at the amplifier. For Bridge amplifier opera- tion, connect the + of the speaker to the R+ of the amplifier and - of the speaker to the L+ of the amplifer. LEFT CHANNEL RIGHT CHANNEL LINE INPUT LINE INPUT LINE

ملخص المحتوى في الصفحة رقم 6

6. SPECIFICATIONS Audio power output: Continuous 50W @ 8 ohms, 75W @ 4 ohms. Frequency response: 20HZ to 20KHZ -0.3dB. Total harmonic distortion: 0.05% 8 Ohm, .075% 4 Ohm Input sensitivity: 400mV line Input impedance: 22k Line Input Signal to noise ratio: 85dB Input trigger: 12VDC 10k Output trigger: 12VDC 150mA Auto off delay time: 2 to 10 minutes Primary fuse: T4A/250V 115VAC, T2A/250V 240VAC Secondary fuse: T6.3A/250V Power requirements: Factory set for 110 VAC 60Hz or 240 VAC 50Hz. IEC 320

ملخص المحتوى في الصفحة رقم 7

5 Forbes Rd. Newmarket, NH 03857, USA 603.659.5170 • Fax 603.659.5388 e-mail: tech@russound.com Come visit us at: