ملخص المحتوى في الصفحة رقم 1
Silhouette SXV2
Phono Preamplifier
Owners Manual
ملخص المحتوى في الصفحة رقم 2
Perreaux Industries Limited makes no warranty for the use of its products, other than those expressly contained in the warranty detailed herein. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change products or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Perr
ملخص المحتوى في الصفحة رقم 3
This page has intentionally been left blank. 2
ملخص المحتوى في الصفحة رقم 4
iiii Introducing the Perreaux Silhouette Series The Perreaux “Silhouette” series represents exceptional engineering at an affordable price. The series incorporates some of the highest levels of audio engineering available today. Key Features Highly flexible for any cartridge Separate low noise input stages for Moving Magnet and Moving Coil cartridges Externally adjustable load impedance and capacitance Multiple gain settings Normal RIAA and IEC RIAA equalisation curves
ملخص المحتوى في الصفحة رقم 5
iiiiiiii Important Safety Instructions Note: Please read all instructions carefully before attempting to operate your Perreaux “Silhouette” SXV2 Phono Preamplifier. ALWAYS switch off power to your system before attempting to connect or disconnect cables. ALWAYS disconnect your system from the mains before attempting to clean your unit. ALWAYS keep electrical equipment out of reach of children. ALWAYS unplug sensitive electronic equipment during electrical storms. NEVER disconnect th
ملخص المحتوى في الصفحة رقم 6
iiiiiiiiiiii Table of Contents i ii i Introducing the Perreaux Silhouette Series .................................... 3 iiii Important Safety Instructions ............................................................. 4 iiii i ii ii ii ii ii i Table of Contents .................................................................................. 5 1 1 1 1 Unpacking and Placement .................................................................. 6 2 2 2 2 Instant Install ......................
ملخص المحتوى في الصفحة رقم 7
1 1 1 1 Unpacking and Placement Unpacking The SXV2 is packaged for maximum protection. To open, sit the Procedure box upright and cut the reinforced tape at the top of the box. The product can now be removed. Pull the grey foam end caps off either side of the unit and remove the black material covering. The SXV2 Phono amplifier is now unpacked and ready for further installation. Note: Please retain all packaging material for future transport. Box 1 x SXV2 Phono Preamplifier Conte
ملخص المحتوى في الصفحة رقم 8
2 2 2 2 Instant Install If you are like us, the first thing you will want to do is to play your favourite piece of music through your new SXV2. The following instructions are written to enable you to achieve this as quickly as possible. These are not comprehensive instructions, but are designed to enable you to play music now! Note: Please take the time to read the SXV2 manual thoroughly as it incorporates many features, which will enhance its operation. Configure SXV2 cartridge s
ملخص المحتوى في الصفحة رقم 9
Switch on SXV2 Insert the power cord supplied into the rear of the SXV2 and into the wall. Switch on the socket at the wall and turn on the power of the SXV2 by setting the power switch down. Caution! Prior to connecting the AC mains, please check the voltage label on the rear panel to ensure that your unit conforms to the power supply in your area. Never attempt to connect the unit to the incorrect voltage. Switch on preamplifier/amplifier Set the volume to the minimum level an
ملخص المحتوى في الصفحة رقم 10
3 3 3 3 Front Panel Functions Power LED This blue LED indicates the power status of your SXV2 Phono Preamplifier. 9
ملخص المحتوى في الصفحة رقم 11
4 4 4 4 Rear Panel Functions Right Channel Cartridge Load Setting DIP Switch Set these switches to correspond with the cartridge manufacturers recommended load figure. For an in depth discussion on this, please refer to Chapter 5. Right and Left Phono Inputs Input from turntable, accepts a standard unbalanced input (RCA). The left channel connection is on the right when looking from the rear, indicated by white inner ring. For more information on input specifications, please r
ملخص المحتوى في الصفحة رقم 12
AC Mains Input An IEC-standard mains input is provided at the rear of the unit. The AC cord set is removable, allowing it to be upgraded at your will. On/Off Switch When operating the switch down, power is applied to the SXV2. Caution! Never switch the SXV2 power ON or OFF with your amplifier turned ON or the respective input selected. Serial Number/Voltage Label The serial number is unique to your SXV2. Please record this number and store it in a safe place. For any ser
ملخص المحتوى في الصفحة رقم 13
5 5 5 5 Customising Your SXV2 The Perreaux SXV2 gives you complete access to all cartridge- loading parameters for each channel via the 12-way rear mounted DIP switches. Two DIP switches are required, as Perreaux engineers have meticulously laid the internal circuitry out on the internal PCB maintaining maximum isolation between channels. Each DIP switch should be set to be a mirror of the other. Cartridge load settings should be set up to directly correspond to the cartridge manufa
ملخص المحتوى في الصفحة رقم 14
Capacitance Use this table to match the capacitance loading characteristics of Loading your SXV2 to that recommended by your cartridge manufacturer. Table Consult your cartridge documentation for the correct capacitance figure. If no capacitance value is recommended, use the lowest setting. C Load Dip Switch Setting (pF) 6 7 8 9 27 UP UP UP UP 74 DOWN UP UP UP 127 UP DOWN UP UP 297 UP UP DOWN UP 417 UP UP UP DOWN Note: Remember to factor in tonearm and interconnect capacitanc
ملخص المحتوى في الصفحة رقم 15
RIAA Two RIAA equalisation settings are selectable – Normal and Equalisation IEC. The equalisation curves are indicated by the charts below. Curve Please select the appropriate equalisation setting for your recording or according to your personal preference. RIAA DIP Switch Curve 12 Normal UP IEC DOWN Normal RIAA Curve IEC RIAA Curve 1 4
ملخص المحتوى في الصفحة رقم 16
Configuration Please use the following example of the popular Thorens TD 295 Example Mk IV turntable equipped with an Ortofon Super OM 40 (Moving Magnet) cartridge as a guideline. Thorens TD 295 Mk IV specifications Tonearm and lead capacitance: 160pF Ortofon Super OM 40 specifications Recommended load resistance: 47kΩ Recommended load capacitance: 200pF-400pF Rated output voltage: 4.0mV SXV2 configuration Resistance loading: 47000Ω Capacitance loading: 74pF (SXV2 capacit
ملخص المحتوى في الصفحة رقم 17
6 6 6 6 Special Design Philosophies Perreaux has been designing and manufacturing only the highest quality audio componentry for more than a quarter of a century. Technology has continued to evolve rapidly over that time and our knowledge and application of design, materials and manufacturing techniques has advanced in tandem with this. Today’s Perreaux range comes closer to fulfilling our shared vision than at any other time in the past. The SXV2 has been developed to meet customer
ملخص المحتوى في الصفحة رقم 18
Minimalist Aesthetics Our products appeal to those who seek the ultimate in audio exclusivity, namely the perfect blend of “form and function”. “Form and function” are both tough masters. We make no excuses for producing some of the most distinctive high-end audio products on the planet. We let “form and function” blend together in perfect harmony. This surely is the essence of true minimalist utilisation. Minimalism in a Wider Context John Pawson writes: “Clearly simplicity has d
ملخص المحتوى في الصفحة رقم 19
7 7 7 7 Special Design Features Construction The front panel is made from high quality solid 6.0mm (0.2”) thick aluminium extrusion featuring our trademark machined Perreaux logo and finished in durable and stylish satin chrome electroplate. On/off status is provided via a discreet blue LED. The chassis and cover are both manufactured from heavy gauge steel. No cover fixing screws are visible. Minimalist styling cues combine seamlessly to allow form and function to blend in harmony and
ملخص المحتوى في الصفحة رقم 20
Gain With a gain range of +40dB to +70dB, the SXV2 is incredibly sensitive. Working in combination with the wide selection of R and C loading the user has no need for messy MM/MC jumpers as any type of cartridge can be matched via the external selectable DIP switch settings. Single Channel Block Diagram RIAA The RIAA equalisation utilises a robust architecture with high Equalisation precision, low noise resistors and highly linear, metalised polyester capacitors for optimum signa
