ملخص المحتوى في الصفحة رقم 1
Telephone Paging Amplifier
10-Watt Model
Installation and Use Manual
Issue 2,August 2002
© 2002 Bogen Communications, Inc.
All rights reserved. 54-2021-01R2 0208
LU10WAMP: PEC Code: 5328-010
COM Code: 408186062
Select Code: 701-000-108
ملخص المحتوى في الصفحة رقم 2
© 2002 Bogen Communications, Inc. All Rights Reserved. Printed in Korea. Notice Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing. However, information is subject to change. Important Safety Information Always follow these basic safety precautions when installing and using the unit: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. DO NOT place the product in a separate enc
ملخص المحتوى في الصفحة رقم 3
Contents Page INTRODUCTION..........................................................................................................................4 PACKAGE CONTENTS..............................................................................................................4 INSTALLATION..............................................................................................................................5 Mounting .........................................................................
ملخص المحتوى في الصفحة رقم 4
Telephone Paging Amplifier Figure 1: Telephone Paging Amplifier Introduction This document describes the Avaya 10-watt Telephone Paging Amplifier.This is a full- featured, wall-mounted amplifier that provides inputs for dry loop 600-ohm telephone page signal and background music source. A set of control inputs allow an external contact closure to mute background music and open the telephone page channel. Background music mute level during page is adjustable and the music slowly fades back in af
ملخص المحتوى في الصفحة رقم 5
Installation Mounting The amplifier is designed for wall mount applications. The 10-watt amplifier weighs 4 lb. NOTE: The amplifier will produce heat during operation which will rise and may cause problems for temperature-sensitive equipment mounted above it. Mount the amplifier near the top of the backboard so that no other equipment will be above it. If this is not possible, then allow at least 12" between the top of the amplifier and the bottom of any equipment positioned above it. Also allow
ملخص المحتوى في الصفحة رقم 6
Telephone Paging Amplifier NIGHT TEL TEL MUSIC BELL CONT IN GND R T Figure 2: Wiring for TEL Input Universal Paging Access Module BGM IN MODE OFF ON T 24VDC PWR SUPPLY S1,S2 PHONE SYSTEM R 48VDC PWR SUPPLY S1,S2 +M CONFIRMATION TONE S3 S4 EXT VOX ENABLE PREANNOUNCE TONE S4 S3 -M PT VOX DISABLE S5 PAGING OUTPUT VOX ENABLE S5 PR N.O. CONTACT CLOSURE A COM PAGE PORT INPUT +24/48 POWER SUPPLY (TRUNK ACCESS ONLY) -24/48 (0.1
ملخص المحتوى في الصفحة رقم 7
Output Wiring All output wiring connections are made to the terminal strip located on the left side of the LU10WAMP. IMPORTANT: Before making any connections or wiring changes to the amplifier or any equipment connected to the amplifier, make sure that the amplifier is NOT plugged into an AC outlet. NOTE: The amplifier does not have a power switch, so it must be unplugged in order to turn the power off. Speaker Connection 70-volt speaker connections are made between the 70V and COM
ملخص المحتوى في الصفحة رقم 8
Operation IMPORTANT: Before plugging the amplifier into an AC outlet, turn all volume controls to their full counterclockwise positions and all other controls to their reference position. Indicator PEAK LEVEL The PEAK LEVEL LED illuminates whenever the speaker output signal level approaches its maximum level. This indicator is used when setting volume levels. Maximum output level is achieved when the PEAK LEVEL indicator flashes intermittently on loud peaks of the input signal. If the indicator
