ملخص المحتوى في الصفحة رقم 1
Model PAB-2100R
400 Watt Stereo Amplifier
Ow Owne ner's r's
Ow Ow Owne ne ner's r's r's
Manual Manual Manual
Manual Manual
ملخص المحتوى في الصفحة رقم 2
INDEX Specifications ................................................................................1 Precautions ...................................................................................2 Installation Instructions .................................................................3 Wiring Instructions ................................................................4 - 5 Stereo and Mixed-Mono Input Wiring Diagram .............................6 Stereo and Mixed-Mono Output Wiring Diagr
ملخص المحتوى في الصفحة رقم 3
HIGH PERFORMANCE STEREO AMPLIFIER This power amplifier has been designed to provide high quality performance with a minimum of maintenance. However, it's performance will only be as good as the HELP! care and quality of components with which it is installed. We therefore advise that you read these instructions very carefully to familiarize yourself with the product 1-800-645-4994 and it's features. Should you require assistance with the installation or wiring of this unit, please call Monday -
ملخص المحتوى في الصفحة رقم 4
PRECAUTIONS 1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. + + 2. The last lead to be connected is the wire to the positive (+ + +) terminal of the battery. Connect this wire only after having completed and checked all other connections to the amplifier. 3. By nature of its design, a power amplifier generates heat an
ملخص المحتوى في الصفحة رقم 5
OFF 12dB 18dB REMOTE CONTROL INSTALLATION DIAGRAM INSTALLATION INSTRUCTIONS 1. Select a mounting area where the amplifier will END PANELS have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode. SELF-TAPPING SCREW 2. Place the amplifier on the mounting surface and mark the locations of the four mounting holes as shown in the illustration. 3. Remove the amplifier and drill a 1/
ملخص المحتوى في الصفحة رقم 6
WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for both types. Please refer to the appropriate diagrams for the system configuration you are using. The power and speaker wire connections for this amplifier are made via screw tightened terminal blocks. Loosen the screw for the connection to be made and fully insert the w
ملخص المحتوى في الصفحة رقم 7
WIRING INSTRUCTIONS 4. Speaker Connections 4. Speaker Connections 4. Speaker Connections 4. Speaker Connections 4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. For leads in excess of 10 feet, #16 gauge is recommended. When wiring the speakers, pay careful attentio
ملخص المحتوى في الصفحة رقم 8
USE THIS INPUT WIRING WITH STEREO AND MIXED-MONO INPUT WIRING DIAGRAM OUTPUT WIRING ON PAGE 7 HIGH-LEVEL LOW-LEVEL CAR STEREO (SPEAKER) OUTPUTS RCA OUTPUTS RIGHT - LEFT RIGHT + LEFT - LEFT + RIGHT IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUTS, NOT BOTH. 1 RCA TYPE 4-PIN SHIELDED CABLE CONNECTOR (NOT INCLUDED) OFF 12dB 18dB REMOTE CONTROL 2 43 6 5 -6- WHITE WHITE w/BLACK STRIPE GRAY GRAY w/BLACK STRIPE
ملخص المحتوى في الصفحة رقم 9
USE THIS OUTPUT WIRING WITH STEREO AND MIXED-MONO OUTPUT WIRING DIAGRAM INPUT WIRING ON PAGE 6 CONNECT THIS WIRE LAST + - m m LEFT RIGHT SPEAKER SPEAKER + - 12 VOLT m m VEHICLE STEREO MODE : 2-8 OHMS STEREO MODE : 2-8 OHMS CHASSIS BATTERY MIXED-MONO MODE : 4-8 OHMS MIXED-MONO MODE : 4-8 OHMS USE #10 GAUGE GROUND WIRE (SEE TEXT) EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT OR GREASE FROM AREA 30 FOR GOOD CONNECTION GROUNDED METAL 20 SECTION OF VEHICLE CAR STEREO + - m m 7 AUTO-ANTENNA LEAD MI
ملخص المحتوى في الصفحة رقم 10
USE THIS INPUT WIRING WITH MONO (BRIDGED) INPUT WIRING DIAGRAM OUTPUT WIRING ON PAGE 9 HIGH-LEVEL (SPEAKER) OUTPUTS LOW-LEVEL CAR STEREO - RCA OUTPUTS + TO 2nd AMPLIFIER TO 2nd - AMPLIFIER + IMPORTANT USE EITHER HIGH OR LOW-LEVEL INPUTS, NOT BOTH. "Y" RCA TYPE SHIELDED CABLE 4-PIN (NOT SUPPLIED) CONNECTOR 1 OFF 12dB 18dB REMOTE CONTROL 25 43 6 -8- WHITE GRAY WHITE w/BLACK STRIPE GRAY w/BLACK STRIPE
ملخص المحتوى في الصفحة رقم 11
USE THIS OUTPUT WIRING WITH INPUT MONO (BRIDGED) OUTPUT WIRING DIAGRAM WIRING ON PAGE 8 CONNECT THIS WIRE LAST + m MONO SPEAKER 12 VOLT OR VEHICLE SUB-WOOFER CHASSIS BATTERY 4 - 8 OHMS - GROUND USE #10 GAUGE m WIRE (SEE TEXT) EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT OR GREASE FROM AREA FOR GOOD CONNECTION GROUNDED METAL SECTION OF VEHICLE 20 CAR STEREO AUTO-ANTENNA LEAD 7 -9-
ملخص المحتوى في الصفحة رقم 12
OPERATION After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. 1 Power Indicator The Power LED functions as a power and warning indicator. The indicator is white when the power to the amplifier is off. When the indicator is green, the amplifier is operating normally. The LED illuminates red to indicate that the self-protection circuits have been activated and have shut off operation of
ملخص المحتوى في الصفحة رقم 13
3 Filter Selector This switch allows selection of the frequency filters that permit the amplifier to be used to reproduce the entire audio range, just the bass, or all frequencies above the bass range. In the "OFF" position of the switch, the response is flat and unaffected so the entire audio frequency range is reproduced by the amplifier. Use this setting if the amplifier is being used to power a full range speaker system. In the "LOW PASS" setting, only the bass frequencies below the frequen
ملخص المحتوى في الصفحة رقم 14
6 Remote Subwoofer Level Control Input This connector permits the amplifier to be used with an optional Remote Control Unit PAB-RC. The PAB-RC control unit allows for adjustment of the bass boost gain level from the passenger compartment. 7 Fuse The circuitry of the amplifier is protected from damage by automotive-type fast-blow fuses. If fuse replacement is necessary, use only fuses of the same ampere rating as originally supplied with the unit. The use of fuses with incorrect ratings may ca
ملخص المحتوى في الصفحة رقم 15
12 / 24 MONTH LIMITED WARRANTY Applies to automotive radios, radio/tape players, radio/CD players, CD changers, power amplifiers, equalizers and accessories. AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned
ملخص المحتوى في الصفحة رقم 16
© 2000 Audiovox Corp., Hauppauge, N.Y. Printed in Korea 128-5719
