ملخص المحتوى في الصفحة رقم 1
SCS-SAT500,300,200 OM 4/25/07 11:39 AM Page 3
THANK YOU FOR CHOOSING JBL
For more than 60 years, JBL ment that you expected – posted on our latest advance-
has been involved in every and that when you think ments, and helps us to better
aspect of music and film about purchasing additional understand our customers
recording and reproduction, audio equipment for your and build products that meet
from live performances to home, car or office, you will their needs and expectations.
the recordings
ملخص المحتوى في الصفحة رقم 2
SCS-SAT500,300,200 OM 4/25/07 11:39 AM Page 2 SPECIFICATIONS SCS SAT500, SCS SAT300 SCS SAT200 Maximum Recommended Amplifier Power Maximum Recommended Amplifier Power 100 Watts 100 Watts Power Handling (Continuous/Peak) Power Handling (Continuous/Peak) 50W/200W 50W/160W Nominal Impedance 8 Ohms Nominal Impedance 8 Ohms Sensitivity 88dB @ 1 Watt/1 meter Sensitivity 86dB @ 1 Watt/1 meter Frequency Response 100Hz – 20kHz (–6dB) Frequency Response 100Hz – 20kHz (–6dB) Tweeter Tweeter 1/2" (13
ملخص المحتوى في الصفحة رقم 3
SCS-SAT500,300,200 OM 4/25/07 11:39 AM Page 4 SPEAKER PLACEMENT FRONT SPEAKERS SURROUND SPEAKERS † 1.5 – 1.8m 5 – 6 ft † Placement for back speakers. † Placement for surround back speaker in a 6.1 system. The SCSSAT500, SCSSAT300 The rear wall is the required It is neither necessary nor and the SCSSAT200 loud- placement for the back sur- desirable to tilt the surround speakers are designed to be round speakers in a 7.1- speakers to aim them down used either singly or in a pair channe
ملخص المحتوى في الصفحة رقم 4
SCS-SAT500,300,200 OM 4/25/07 11:39 AM Page 5 ATTACHING THE SHELF STAND TO THE SPEAKER Prepare the speaker wire as conductor through the hole is snug. Follow the same described on Page 5. Thread on the right looking at the procedure to connect the the two conductors through stand from the front. Push negative wire to its terminal. the two holes in the stand down on the red speaker Use the larger screw bracket. Make sure to pre- terminal and insert the bare (Hardware Bag A) in the serve the pr
ملخص المحتوى في الصفحة رقم 5
SCS-SAT500,300,200 OM 4/25/07 11:39 AM Page 6 WALL-MOUNTING and the back of the Satellite 4 Speaker¶, using large 3 2 needle-nose pliers until it is firmly seated against the back 1 of the Satellite Speaker¶ and has locked the Ball and Shaft£ and the Satellite Speaker¶ together. 8 NOTE: Once the Metal Nut¡ 5 is fully tightened, it may embed some marks on the back of the Satellite Speaker¶. However, Important Safety Note: The Step 3: Slide the Molded Nut these marks will be covered customer
ملخص المحتوى في الصفحة رقم 6
SCS-SAT500,300,200 OM 4/25/07 11:39 AM Page 7 Such damage would not be not to cross-thread. The ruin the intended effect by covered under the warranty. swiveling ball enables you to calling too much attention aim the speaker to one side to the information in those Step 7: Holding the Satellite or the other, or to tilt it up channels. Speaker¶ with both hands, or down. Although stereo reinsert the ball portion of Step 9: Once the speaker’s imaging may be improved the Ball and Shaft£ into ori
ملخص المحتوى في الصفحة رقم 7
SCS-SAT500,300,200 OM 4/25/07 11:39 AM Page 8 SYSTEM CONNECTION Connect each speaker to Configure your receiver or The SCS SAT500/300/200 the corresponding speaker processor to reflect the should be set to “Small.” If terminals on your receiver correct number of speakers your receiver allows you to or amplifier. in your system. If you have set the crossover frequency added one SCSSAT500/300/200 between the subwoofer and If you are using a subwoofer, speaker to a 5.1-channel the speakers, sele
ملخص المحتوى في الصفحة رقم 8
SCS-SAT500,300,200 OM 4/25/07 11:39 AM Page 9 TROUBLESHOOTING If there is no sound from any followed the speaker, con- • Make sure the movie or of the speakers: sult your dealer for further TV show you are watching assistance or, if that is not is recorded in a surround • Check that receiver/amplifier possible, visit www.jbl.com. sound mode. If it is not, is on and a source is playing. check to see whether your If the system plays at low • Check all wires and con- receiver/amplifier has oth
