ملخص المحتوى في الصفحة رقم 1
Installation/Operation
Automatic
Washers
Metered Commercial
TLW12C
TLW12C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 202068R5
www.comlaundry.com August 2011
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
WARNING For your safety and to reduce the risk of fire or an explosion, do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. W022 IMPORTANT: Read the complete INSTALLATION/OPERATION INSTRUCTIONS before using the washer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 202068 1
ملخص المحتوى في الصفحة رقم 4
Safety Information.............................................................................. 3 Table of Explanation of Safety Messages........................................................... 3 Important Safety Instructions ............................................................... 3 Contents Installation........................................................................................... 5 Dimensions and Specifications...........................................................
ملخص المحتوى في الصفحة رقم 5
Safety Information Explanation of Safety Messages Important Safety Instructions Throughout this manual and on machine decals, you Save These Instructions will find precautionary statements (“DANGER,” “WARNING,” and “CAUTION”) followed by specific WARNING instructions. These precautions are intended for the personal safety of the operator, user, servicer, and To reduce the risk of fire, electric shock, those maintaining the machine. serious injury or death to persons when using your washer,
ملخص المحتوى في الصفحة رقم 6
Safety Information 7. Do not allow children to play on or in the washer. 15. Keep your washer in good condition. Bumping or Close supervision of children is necessary when dropping the washer can damage safety features. the washer is used near children. This appliance If this occurs, have your washer checked by a is not intended for use by persons (including qualified service person. children) with reduced physical, sensory or 16. Do not repair or replace any part of the washer, or mental c
ملخص المحتوى في الصفحة رقم 7
Installation Dimensions and Specifications 22.44 in. (57 cm) 1 C H 0.44 in. 26 in. (66.04 cm) 25.625 in. (65.1 cm) (1.12 cm) 28 in. (71.1 cm) TLW2097N TLW2097N 1 Pilot Hole 202068 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5 30.5 in. (74.47 cm) 28.75 in. (73.02 cm) 41.25 in. (104.78 cm) 36 in. (91.44 cm) 38.19 in. (97 cm) Standard Capacity Meter Case 43 in. (109.2 cm) High Capacity Meter Case 43.875 in. (111.44 cm) 51 in. (129.54 cm)
ملخص المحتوى في الصفحة رقم 8
Installation Before You Start Installing the Washer Tools Step 1: Remove the Shipping Brace and Shipping Plug For most installations, the basic tools you will need are: Remove the shipping brace from under the lid. The shipping plug will be released from the base of the 1 washer when removing the cardboard base from the 2 washer. Refer to Figure 2. 3 The shipping brace and plug should be saved and must be reinstalled whenever washer is moved or transported to a new location. This will pre
ملخص المحتوى في الصفحة رقم 9
Installation Step 2: Wipe Out Inside of Washtub Water Supply Requirements Prior to first wash, use an all purpose cleaner or a Water supply faucets must fit standard 3/4 inch detergent and water solution and a damp cloth to (19.1 mm) female garden hose couplings. DO NOT remove shipping dust from inside of washtub. USE SLIP-ON OR CLAMP-ON CONNECTIONS. NOTE: Water supply faucets should be readily accessible to permit turning them off when washer is not being used. Recommended cold water temper
ملخص المحتوى في الصفحة رقم 10
Installation Connecting Hoses IMPORTANT: Turn off water supply faucets after check-out and demonstration. Owner should turn Insert rubber washers and filter screens (from off water supply whenever there will be an accessories bag) in water fill hose couplings (two extended period of non-use. hoses supplied with washer). Connect fill hoses to water supply faucets. Then connect the hoses to the NOTE: Longer fill hoses are available (as optional hot and cold valve connections at the rear of
ملخص المحتوى في الصفحة رقم 11
Installation Step 4: Connect Drain Hose to Drain If necessary, follow the instructions for your type of drain receptacle (high standpipe or low standpipe) to Receptacle properly install the drain hose. Drain Facilities High Standpipe Installation IMPORTANT: The drain hose installation is a very NOTE: No. 562P3 Siphon Break Kit and No. 25863 important factor in the washer installation. If care Hose Coupling are not required for this type of is not taken when the drain hose is installed, a
ملخص المحتوى في الصفحة رقم 12
Installation Low Standpipe Installation If washer is not level, tilt washer back to access the front leveling legs. Loosen the locknuts and adjust legs If the drain facility is lower than the cabinet top, a by screwing into or out of washer base. siphon break kit, Part No. 562P3, must be installed in Once adjusted, tilt the washer forward on front legs the drain hose to prevent siphoning action and drain and lower back down into position to set the rear self- hose MUST be cut to fit the wa
ملخص المحتوى في الصفحة رقم 13
Installation Step 6: Plug In the Washer Electrical Requirements 2 (120 Volt, 60 Hertz with 3-Prong Grounding Plug) 3 1 NOTE: The wiring diagram is located in the control hood. 120±12 0 V.A.C. V.A.C. WARNING 120±12 To reduce the risk of fire, electric shock, V.A.C. 5 4 serious injury or death, all wiring and grounding MUST conform with the latest edition of the National Electrical Code, Standard 120 Volt, 60 Hertz ANSI/NFPA No. 70, and such local 3-Wire Effectively regulations as might a
ملخص المحتوى في الصفحة رقم 14
Installation Grounding Instructions NOTE: The agitator should not be removed except for service. The washtub is designed to be self- The washer must be grounded. In the event of cleaning. malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. The washer is equipped with a cord having an equipment-grounding conductor and a three-prong grounding plug. The plug must be plugged into an appropriate outlet that i
ملخص المحتوى في الصفحة رقم 15
Installation Models Prepped for Card Reader Vending The machine is shipped from the factory with the Meter Case Electronic Control Diagnostic Harness Assembly The factory mounted coin meter case does not include unplugged. To avoid unauthorized manual the service door lock, coin drawer, coin drawer lock or programming or vending, perform the following steps. keys. These parts must be ordered (at extra cost) 1. Open control panel. Refer to Figure 13. according to the purchaser’s requirements
ملخص المحتوى في الصفحة رقم 16
Installation Additional Washer Security 4. Insert Phillips head screw down through double “D” hole in left rear corner of cabinet top (inside (Coin Models Only) control hood) until it engages retainer nut located on left rear corner gusset of cabinet. Located on the service door of the washer is a flat Phillips head screw. During shipment, this screw is 5. Finger tighten screw. used to attach the service door to the meter case. For additional security, this screw can be reinstalled inside
ملخص المحتوى في الصفحة رقم 17
Operation Step 2: Load Laundry Operation Instruction Load dry clothes loosely into washtub – DO NOT IMPORTANT: Prior to first wash, use an all- overload! purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from When washing large items such as shag rugs and inside of washer. bedspreads, add several small items to balance wash load. IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation. Ste
ملخص المحتوى في الصفحة رقم 18
Operation Step 4: Set Fabric Selector Step 6: Select Cycle Type/ Soil Level Push CYCLE SELECT or SOIL LEVEL touchpad. Push touchpad for NORMAL, PERM PRESS or Light indicates selection. DELICATES. Light indicates selection. TLW2138N TLW2138N TLW2118N Figure 18 TLW1 TLW12R TLW2118N Step 5: Set Wash Temperature Figure 20 Push touchpad for HOT, WARM or COLD. Light Step 7: Insert Money or Card indicates selection. To Insert Money Insert coin(s) in coin slot. Check pricing as seen on digital disp
ملخص المحتوى في الصفحة رقم 19
Operation To Insert Card Indicator Lights Insert card into opening. INSERT COINS/CARD INSERT COINS/CARD is lit to prompt the user to insert coins or a card to satisfy the vend price. When INSERT COINS/CARD is lit, the digits show the vend price remaining to be satisfied. WASH WASH is lit at the beginning of the Wash portion of the cycle and will remain lit until the Wash step is complete. RINSE RINSE is lit at the beginning of the Rinse or Extra Rinse portion of the cycle and will remain l
ملخص المحتوى في الصفحة رقم 20
Maintenance Reinstallation of Shipping Materials User-Maintenance Instructions Shipping Brace Cold Weather Care The shipping brace in the lid opening should be saved If the washer is delivered on a cold day (below and reinstalled whenever the washer is moved. To freezing), or is stored in an unheated room or area reinstall the brace, open the washer lid and place the during the cold months, do not attempt to operate the brace over the washer agitator, placing the back of the washer until
