ملخص المحتوى في الصفحة رقم 1
Product Manual
®
Momentus 5400.3 SATA
Blade Server
ST9160821SB
ST9120822SB
ST9100828SB
ST980815SB
ST960815SB
ST9402116SB
100418128
Rev. E
August 2007
ملخص المحتوى في الصفحة رقم 2
©2004-2007, Seagate Technology LLC All rights reserved. Publication number: 100418128, Rev. E August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, Seagate- SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registere
ملخص المحتوى في الصفحة رقم 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary table . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 4
ii Momentus 5400.3 SATA Blade Server Product Manual, Rev. E
ملخص المحتوى في الصفحة رقم 5
List of Figures Figure 1. Typical +5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 4. Mounting dimensions—top, side and end view . . . . . . .
ملخص المحتوى في الصفحة رقم 6
ملخص المحتوى في الصفحة رقم 7
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus 5400.3 SATA Blade Server model drives: � ST9160821SB � ST9120822SB � ST9100828SB � ST980815SB � ST960815SB � ST9402116SB These drives provide the following key features: � 5,400 RPM spindle speed. � 8-Mbyte buffer. � Quiet operation. Fluid Dynamic Bearing (FDB) motor. � High instantaneous (burst) data-transfer rates (up to 150 Mbytes per second). � Perpendicular re
ملخص المحتوى في الصفحة رقم 8
1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: � Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump- ers or other configuration options. � Thinner and more flexible cabling for improved enclosure airflow and ease of installation. � Scalability to higher performance levels. In addition, Serial ATA makes the transition f
ملخص المحتوى في الصفحة رقم 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST9160821SB, ST9120822SB, ST9100828SB, ST980815SB, ST960815SB, and ST9402116SB models. 2.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification measurement or defi- nition, see the appropriate
ملخص المحتوى في الصفحة رقم 10
Table 1: Drive specifications Drive specification ST9160821SB ST9120822SB ST9100828SB ST980815SB ST960815SB ST9402116SB Average seek, read (msec typical) 11.0 Average seek, write (msec typical) 13.0 Average random seek (msec) 12.5 Full-stroke seek (msec) 22 (typical); 24 (max) Startup current, +5V (typical) 1.0 amps Seek power (typical) 2.0 watts Read/write power (typical) Read: 1.9 watts; Write: 1.8 watts Idle mode, low power (typical) 0.6 watts Standby mode 0.2 watts (typical)** Sleep mode 0.2
ملخص المحتوى في الصفحة رقم 11
Table 1: Drive specifications Drive specification ST9160821SB ST9120822SB ST9100828SB ST980815SB ST960815SB ST9402116SB Warranty 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty
ملخص المحتوى في الصفحة رقم 12
2.4 Physical organization Drive model Read/write heads Number of discs ST9160821SB 4 2 ST9120822SB 3 2 ST9100828SB 3 2 ST980815SB 2 1 ST960815SB 2 1 ST9402116SB 1 1 2.5 Recording and interface technology Interface Serial ATA (SATA) Recording method Perpendicular Recording density BPI (bits/inch max) 870k Track density TPI (tracks/inch max) 150k 2 Areal density (Gbits/inch max) 132 Spindle speed (RPM) (± 0.2%) 5,400 Maximum Internal transfer rate (Mbits/sec) 352 I/O data-transfer rate (Mbytes/
ملخص المحتوى في الصفحة رقم 13
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. Table 2: Typical seek times Typical seek times (msec) Read Write T
ملخص المحتوى في الصفحة رقم 14
� Idle mode power Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location. � Standby mode During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/ write electronics are in power-down model Table 3: DC power Power dissipation +5V input average (25° C) Spinup 1.0 A Seek 2.0 watts Read 1.9 watts Write 1.8 watts Idle, performance mode* 1.4 watts Idle, active* 0.75 watts Idle, l
ملخص المحتوى في الصفحة رقم 15
2.9.2 Deferred spinup Momentus 5400.3 SATA drives provide a deferred spinup feature which storage subsystem controllers can use to sequence disc drive initialization. This is beneficial to systems which include multiple Serial ATA hard disc drives because it allows subsystem controllers to stagger the spinup of each drive to accommodate available power supply current. This feature does not impact time-to-ready in typical desktop systems. To accommodate the deferred spinup of multiple disc dri
ملخص المحتوى في الصفحة رقم 16
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Duty 50%, power-on hours (POH) of 8,750 per year (24 hours per day, 7 days per week operation). Actual drive case temperature should not exceed 45°C (113°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating: 0° to 40°C (32° to 104°
ملخص المحتوى في الصفحة رقم 17
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 350 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.10.5.2 Nonoperating shock The nonoperating shock leve
ملخص المحتوى في الصفحة رقم 18
2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea- surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per sec
ملخص المحتوى في الصفحة رقم 19
2.13 Reliability Measurement type Specification 14 Nonrecoverable read errors 1 per 10 bits read, max. Annualized Failure Rate (AFR) 1.79% at maximum case temperature of 40°C and 8,760 power on hours (POH). Load/Unload (U/UL) 25°C, 50% relative humidity 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles 32°C, 80% relative humidity 600,000 software-controlled power on/off cycles 5°C, 80% relative humidity 20,000 hard power on/off cycles 5°C, 10% relat
ملخص المحتوى في الصفحة رقم 20
Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para- graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil- ity (EMI/EMS) for Cla
