ملخص المحتوى في الصفحة رقم 1
INSTRUCTION
MANUAL
White LED Camera
VL5700BPVF
VL5700BPVFW
Speco Technologies is constantly developing product improvements.
We reserve the right to modify product design and specifications without notice and without incurring any obligation. Rev. 6/9/10
ملخص المحتوى في الصفحة رقم 2
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT REMOVE COVER(OR BACK). CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK NO USER-SER VICEABLE PARTS INSIDE. CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ملخص المحتوى في الصفحة رقم 3
Contents 3 Contents Precautions 4 5 Sefety Instructions Menu Set Up ▶OSD Control Button 7 ▶Set Up Menu 8 11 ▶Menu Set Up 12 ▶Lens ▶Exposure 13 15 ▶Back Light ▶White Bal. 18 ▶Day & Night 19 ▶3DNR 21 ▶Special 22 ◈Camera Title 22 ◈D - Effect 25 27 ◈Motion ◈Privacy 28 ◈Defect 29 ▶Adjust 30 ▶Reset 31 31 ▶Exit Trouble Shooting 32 - 3 -
ملخص المحتوى في الصفحة رقم 4
Precautions Do not install the camera in Do not install the camera under Do not touch the front lens of the extreme temperature conditions. unstable lighting conditions. camera. Only use the camera under conditions Severe lighting change or flicker can This is one of the most important parts of the where temperatures are between cause the camera to work improperly. camera. Be careful not to leave -10°C and +50°C. Be especially careful to provide fingerprints on the lens cover. ventilation when
ملخص المحتوى في الصفحة رقم 5
Sefety Instructions Precautions for use ◑ This camera should be installed by qualified personnel only ◑ There are no user serviceable parts inside ◑ Do not disassemble this camera other than to make initial adjustments ◑ Use a UL approved regulated 24 volt AC or 12 volt DC power supply ◑ Use appropriate low voltage power cable to prevent fire or electrical shock ◑ Please insure that your installation area can support the weight of the camera Please handle this camera carefully : ◑ Do n
ملخص المحتوى في الصفحة رقم 6
White LED Camera DC Auto Iris Varifocal Lens(4mm-9mm) / IR LED Built-in 14pcs + White LED 2pcs VL5700BPVF ■ ■ VL5700BPVFW 600TV Lines DC Auto Iris Varifocal Lens (4mm-9mm) True Day/Night Capability ICR-IR Cut Filter Removable 850nm IR LEDs * 14pcs White LED * 2pcs CDS White LED IR LED's 14EA & White LED's 2EA & Heater 1EA SPECIFICATIONS MODEL VL5700BPVF / VL5700BPVFW 1/3" SONY Super HAD ll CCD Sensor NTSC=811(H) * 508(V) / PAL=795(H) * 595(V) Total Pixels NTSC=768(H) * 494(V) / PAL=752(H) * 582(
ملخص المحتوى في الصفحة رقم 7
OSD Control Button 1. Type A, Type B, Type C of OSD button could be used when it needs to OSD control. 2. Type D is extra Option (wired Remote controller) - 7 -
ملخص المحتوى في الصفحة رقم 8
How to Set Up the camera menu ● Setup Menu - 8 -
ملخص المحتوى في الصفحة رقم 9
- 9 -
ملخص المحتوى في الصفحة رقم 10
- 10 -
ملخص المحتوى في الصفحة رقم 11
Menu Set Up Menu items can be selected by using the OSD buttons of the camera 1. Press the Set Up button. * The Set Up menu will be displayed on the monitor. SETUP 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.DAY / NIGHT COLOR 5.3DNR ON 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT 2. Move and select the required function using the Up and Down button. * Move the arrow indicator Up or Down to select the desired feature by pressing the Up or Down button. SETUP 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.DAY / NIGHT
ملخص المحتوى في الصفحة رقم 12
3. Change menu settings using the Left or Right button. * Available values or Status are displayed by pressing the Left or Right buttons. Press the button until desired value / status is displayed. 4. After Changing the setting move the arrow indicator to EXIT and press the SET button to EXIT. NOTE * Move to the available submenu by moving arrow to desired feature. * Submenu is not available when this symbol is display "- - - -" Lens 1. Move the arrow indicator to LENS using the
ملخص المحتوى في الصفحة رقم 13
NOTE * When DC is selected, the brightness can be adjusted. The brightness control range is 1 ~ 100. Lens BRIGHTNESS 100 RETURN 3. Press the RETURN to return to the SETUP menu. Exposure This function is used to select Automatic or Manual shutter speed control. 1. On the Set Up menu screen select EXPOSURE by using the Up or Down button. 2. Select the desired shutter mode by pressing the Left or Right button. SETUP 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.DAY / NIGHT COLOR 5.3DNR ON 6.SPECIAL 7.ADJU
ملخص المحتوى في الصفحة رقم 14
EXPOSURE SHUTTER AUTO AGC MIDDLE SENS-UP AUTO BLC OFF D-WDR OFF RETURN RET NOTE *Shutter: Select Shutter using the Up or Down button, you can adjust the shutter speed from 1/60, FLK, 1/250~1/100,000. →FLK: Select FLK mode if flickering occurs; caused by the unmatched frequency of electric light. If select FLK mode, sense-up does not operate. * AGC(AUTO GAIN CONTROL): A higher gain increases brightness but also increases any noise. OFF : Deactivates the AGC function LOW : Sets automatic gain c
ملخص المحتوى في الصفحة رقم 15
* RETURN: Select Return to save the changes in the EXPOSURE menu and retun to the SETUP menu. NOTE * Pressing the SET button in AUTO mode allows adjustment of image brightness by increasing or decreasing the shutter speed (x2 ~x256). * The higher the level, the brighter the image becomes, but it is possible that an after image (ghosting) could appear. * When SENS-UP is activated the increased magnification can induce noise and pixelation; this is quite normal. Back Light(BLC) This ca
ملخص المحتوى في الصفحة رقم 16
POSITION SIZE PICTURE 1 PICTURE 2 * HSBLE: HSBLC function is especially effective for reading car number plates at the night time. You can select and define the required observation area for the target object and ignore a strong light area. Press the "ENTER" button at the AREA menu, you can change the position as shown in Picture 1. Press the "ENTER" button again after area setting, you can change the position as shown in Picture 2. Default: Press the Default to return to factory defaults. HSBLC
ملخص المحتوى في الصفحة رقم 17
HSBLC OFF HSBLC ON * D-WDR: This camera which is using 3D-DNR DSP provides intelligent light level control to overcome even strong backlight conditions. →OFF: D-WDR function does not operate. When there are simultaneous bright & dark image area WDR makes them both distinct and can be selected as OUTDOOR and INDOOR. D-WDR LOW-LEVEL 5 HIGH-LEVEL 5 RETURN RET D-WDR OFF D-WDR ON * RETURN: Select Return to save the changes in the EXPOSURE menu and return to the SET
ملخص المحتوى في الصفحة رقم 18
White Balance The White Balance function is used to control the “on-screen” colors. 1. Move the arrow indicator to WHITE BAL on the SETUP menu screen using the Up and Down button. 2. Select the desired mode by using the Left or Right button. SETUP 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.DAY / NIGHT COLOR 5.3DNR ON 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT * There are three user selectable White Balance settings available. * ATW : (Auto Tracking White Balance) Normal setting; when the color temperature ra
ملخص المحتوى في الصفحة رقم 19
Day / Night Picture can be displayed in either colour of black and white. 1. Select DAY / NIGHT using the Up or Down button on the SETUP menu screen. SETUP 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.DAY / NIGHT AUTO 5.3DNR ON 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT 2. Select the desired mode using the Left and Right buttons. * COLOR : The picture is always displayed in color. * BW : This picture is always displayed in black and white. Select BW using the button and press the menu to activate COLOR BURST o
ملخص المحتوى في الصفحة رقم 20
IR SMART GAIN 10 SIZE AREA RETURN RET AREA SMART IR OFF SMART IR ON → AUTO: The mode will automatically switches to COLOR in normal condition and switches to BW mode when ambient illumination is low. Press the SET button to set the switching time or D→N(AGC), N→D(AGC) in AUTO mode. DAY & NIGHT AUTO DELAY 5 D→N(AGC) 170 N→D(AGC) 70 RETURN RET - 20 -
