ملخص المحتوى في الصفحة رقم 1
®
HS8000/HS8013 High-Security
Camera Enclosures
Installation/Operation Manual
C480M-F (10/04)
Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
ملخص المحتوى في الصفحة رقم 2
CONTENTS Section Page 1.0 GENERAL ..................................................................................................1 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ...............................1 2.0 DESCRIPTION ..........................................................................................2 2.1 OPTIONS ...........................................................................................2 3.0 INSTALLATION .................................................................
ملخص المحتوى في الصفحة رقم 3
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco
ملخص المحتوى في الصفحة رقم 4
2.0 DESCRIPTION The HS8000/HS8013 is a high security camera enclosure designed for installa- tions such as prisons, detention cells, etc., requiring maximum protection from van- dalism. Constructed from heavy gauge steel, the HS8000 will accept most CCD cameras with fixed focal length lenses ranging in size from 4 mm to 75 mm. Larger lens size combinations can be considered when using the HS8013. There is no exposed mount- ing hardware securing the HS8000/HS8013 to its mounting surface. Opening
ملخص المحتوى في الصفحة رقم 5
3.0 INSTALLATION NOTE: Unless otherwise noted all Before installing the enclosure to a wall or ceiling, make certain that the mounting instructions, drawing, etc. apply to surface is able to support the full load of the enclosure plus all other equipment such as camera, lens, etc. both the HS8000 and HS8013 except for the ceiling adapter. The The tilt table bracket may be removed to provide adequate clearance for mounting HS8000CA ceiling adapter will not the enclosure. work with the HS8013. N
ملخص المحتوى في الصفحة رقم 6
3/8" Mounting Hole, 4X 1" Cable Entry Hole, 2X HS8000/HS8013 Mounting Template 3.25" .75" 2.0" Figure 1. HS8000/HS8013 Mounting Template
ملخص المحتوى في الصفحة رقم 7
3.2 WALL/CEILING MOUNTING To mount the enclosure to a wall or ceiling, follow the steps outlined below. 1. Remove the two (2) tamper-resistant screws and open the cover. A special socket is provided (fits 1/4" square drive). 2. Using the enclosure or the template provided (see Figure 3), mark and drill holes in the mounting surface. 3. Knock out any of the two (2) cable entry holes desired on the enclosure body. 4. Attach the enclosure with the required fasteners. 5. Route all cables through th
ملخص المحتوى في الصفحة رقم 8
3.4 HS8000CA CEILING ADAPTER PLATE INSTALLATION (For HS8000 only) Before installing the HS8000CA ceiling adapter plate, make sure the mounting sur- face is able to support the full load of the enclosure, mount, and all other equipment such as the camera, lens, etc. NOTE: The HS8000CA ceiling To install the HS8000CA ceiling adapter plate, perform the following: adapter plate is provided with six (6) 1. Place the HS8000CA ceiling adapter plate on the HS8000 enclosure as shown 10-32 screws, nuts a
ملخص المحتوى في الصفحة رقم 9
3.5 OPTIONAL HK8000/HK8024 HEATER KITS The HK8000 and HK8024 Heater Kits require 120 VAC or 24 VAC respectively, and both provide 80 watts of heat which is thermostatically controlled to activate at 40° F and turn off at 60° F 3.5.1 Recommended Cable Size The following cable sizes are the minimum recommended for use with heater kits. 120 VAC Operation 24 VAC Operation 22 Awg to 400 ft (121.9 m) 20 Awg to 35 ft (10.7 m) 20 Awg to 650 ft (198.12 m) 18 Awg to 60 ft (18.3 m) 18 Awg to 1,100 ft (33
ملخص المحتوى في الصفحة رقم 10
3.7 CAMERA/LENS INSTALLATION NOTE: The tilt table bracket and tilt Now that the proper window viewing location has been determined and the enclo- sure has been mounted, you are ready to mount your camera lens to the enclosure. table may be removed from the en- Refer to the following steps. closure to aid in camera/lens instal- lation. 1. Loosen the tilt table mounting bolts. 2. Securely attach the camera/lens to the desired location on the tilt table. 3. Make all necessary electrical connectio
ملخص المحتوى في الصفحة رقم 11
4.0 CARE AND MAINTENANCE Regularly scheduled maintenance will help prolong the operational life and appear- ance of the equipment. Clean the viewing window regularly with a soft cloth, using a mild, nonabrasive detergent and water solution to help maintain picture clarity. Pelco Manual C480M-F (10/04) 9
ملخص المحتوى في الصفحة رقم 12
5.0 EXPLODED ASSEMBLY DRAWING Figure 6. HS8000 Exploded Assembly Drawing Table A. Mechanical Parts List Item Quantity Description Part Number 11 Window, Lexan, 5.75" x 4" x .5", MR5 AH800010001 21 Body (HS8000) AH80001000WA 1 Body (HS8013) HS80131000WA 31 Hinge, steel HS80004008COMP 41 Cover, body AH80004012COMP 51 Bracket, tilt table mount (HS8000) AH80004014COMP 1 Bracket, tilt table mount (HS8013) HS80134000COMP 61 Tilt table AH80004013COMP 71 Plate, blank window AH80004015COMP 82 Screw, 1
ملخص المحتوى في الصفحة رقم 13
6.0 SPECIFICATIONS MECHANICAL Window: 1/2" (1.27 cm) thick; impact and abrasion resistant Lexan Camera Mounting: Adjustable tilt table Camera and Lens Size: Accepts camera and lens combinations (including BNC connector) up to: HS8000 4.0" H x 4.0" W x 8.0" L (10.16 cm x 10.16 cm x 20.32 cm) HS8013 4.0" H x 4.0" W x 11.0" L (10.16 cm x 10.16 cm x 27.94 cm) Enclosure Mounting: Four (4) .390" (0.99 cm) diameter holes on protected rear surface Security: Tamper-resistant screws N.O./N.C. switch cont
ملخص المحتوى في الصفحة رقم 14
Figure 7. HS8000/HS8013 Dimension Drawing Figure 8. HS8000CA Ceiling Adapter Plate Dimension Drawing 12 Pelco Manual C480M-F (10/04)
ملخص المحتوى في الصفحة رقم 15
NOTES Pelco Manual C480M-F (10/04) 13
ملخص المحتوى في الصفحة رقم 16
7.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products and the following fixed camera models: CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X. ® • Three years on all other fixed camera models (including Camclosure In
