ملخص المحتوى في الصفحة رقم 1
Day/Night DNS Fixed
Dome Camera
NTSC / PAL
HD4D HD4DX
User Guide
Document 800-00023 – Rev D – 05/07
ملخص المحتوى في الصفحة رقم 2
Revisions Issue Date Revisions A 04/07 New document. B 05/07 Increase line weight of illustrations. C 05/07 Corrected specifications. D 06/07 Changes: Page 14, LL switch is on power supply board. Page 18, corrected Day/Night mode explanation. Page 24, corrected Vertical Phase Adjustment to 0 - 359°. 2
ملخص المحتوى في الصفحة رقم 3
Warnings Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. WARNING! 12 VDC/24 VAC models require the use of CSA Certified/UL Listed Class 2 power adapters to ensure compliance with electrical safety standards. WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems).
ملخص المحتوى في الصفحة رقم 4
FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
ملخص المحتوى في الصفحة رقم 5
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Unpack Everything. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Mounting the
ملخص المحتوى في الصفحة رقم 6
Introduction The unobtrusive, low-profile design of the HD4D CCTV Camera is ideal for indoor and outdoor installations in commercial and residential venues. Before You Begin Please read this guide carefully before you install the HD4D CCTV Camera. Keep this guide for future reference. Unpack Everything Check that the items received match those listed on the order form and packing slip. The HD4D packing box should include, in addition to this User Guide: � One fully-assembled HD4D camera, inclu
ملخص المحتوى في الصفحة رقم 7
Installation The HD4D is weather-sealed for indoor or outdoor locations. The HD4D is a fully-integrated enclosure with camera and lens. The wiring can be completely concealed to reduce the risk of tampering. Figure 1 Installation Components HD4D dome enclosure Document 800-00023 Rev D 7 05/07
ملخص المحتوى في الصفحة رقم 8
Mounting the Camera The HD4D Camera is designed to be surface mounted on a wall or ceiling. Before you mount the camera, use the mounting template provided to mark and pre-drill the holes. Connecting Cables Through the Housing Base For installations requiring pulling cables through the grommet located in the bottom of the base: 1. Use a sharp knife to cut an ! opening in the base gasket (see the figure below). Be careful. The opening should only be big enough to feed the cable assembly throug
ملخص المحتوى في الصفحة رقم 9
Connecting Cables Through the Side Conduit 1. Peel back the bottom flat gasket below the side conduit just enough to expose the security screw. 2. Use the Allen key supplied to loosen and remove the security screw (see below). 3. Use a flat screwdriver to unscrew the conduit plug. 4. Pull the cabling through the hole. 5. Apply appropriate sealant around the opening to prevent moisture from entering the housing. security screw supplied allen key Document 800-00023 Rev D 9 05/07
ملخص المحتوى في الصفحة رقم 10
Electrical Box Installations Figure 2 illustrates how to mount the HD4D directly to a 4S electrical box or directly to wall or ceiling. For 4S electrical box installations, the optional adapter plate can be used to cover ceiling or wall imperfections around the electrical box opening. Figure 2 4S Electrical Box Installation Electrical box (not supplied) Ceiling/wall Secure the optional Adapter plate adapter plate to the (use is optional) 4S electrical box using appropriate screws (not s
ملخص المحتوى في الصفحة رقم 11
Figure 3 illustrates how to mount the HD4D directly to a double gang or single gang electrical box. Figure 3 Double Gang/Single Gang Electrical Box Installation (Single Gang Shown) Electrical box (not supplied) Ceiling/wall HD4D base Secure the HD4D base with screws appropriate to your installation (not supplied) For surface mount installations (without an electrical box), use #6-1 7/16 inch slotted Type A screws (x4) supplied Document 800-00023 Rev D 11 05/07
ملخص المحتوى في الصفحة رقم 12
Connecting the Wiring Follow Figure 4 for the wiring connection. Figure 4 Wiring Connection Note For secure installations, surface mounted cables should be protected by plastic or metal cable covers. Video: female BNC (yellow) + Red Power: 12 VDC - Black or 24 VAC 12
ملخص المحتوى في الصفحة رقم 13
Adjusting the Camera To adjust the HD4D Camera: 1. Apply 12 VDC or 24 VAC power to the camera and monitor the video signal. 2. Loosen the screws that lock the gimbal assembly in place (see Figure 5). 3. Adjust the camera carrier to the desired view. 4. Tighten the screws to lock the gimbal assembly in place. Note Orient the camera as shown in Figure 5 to maintain the correct picture orientation. Figure 5 Gimbal Adjustment Top view Angle view Setscrews (x2). Loosen to adjust Pan (C). Other Loc
ملخص المحتوى في الصفحة رقم 14
Line Lock The Line Lock switch on the power supply board must be left in the ON position. To switch between Line Lock and Internal Lock, use the OSD menu (see Sync Control Setup, page 19). Adjusting the Lens Focus Lenses are pre-focused at the factory but may require a final adjustment after installation in the unlikely event the optical effect of the dome causes a slight defocusing of the lens. TECH TIP! To check the focus, hold the dome over the lens while making any adjustments. To adjust
ملخص المحتوى في الصفحة رقم 15
R T L F D N Camera Settings Camera Functions Figure 6 Camera Controller 2 Legend #Description Video-test monitor output connector 1 Camera OSD control (four position plus center push) 2 Press this control To do this UP, DOWN Select a new item LEFT, RIGHT Select a menu item SETUP (MENU) Enter SETUP MENU, (CENTER PUSH) access a submenu 1 Document 800-00023 Rev D 15 05/07
ملخص المحتوى في الصفحة رقم 16
OSD Menu Structure The HD4D camera menu system consists of one main setup menu for easy programming. Main MENU Sub-Menus Options SETUP MENU LENS DC↵ 1 VIDEO MANUAL SHUTTER FLK (FLICKERLESS) 2 ESC↵ MANUAL↵ ATW WHITE BAL. 3 MANUAL↵ AWC↵ OFF BACKLIGHT LOW 4 MIDDLE HIGH OFF AGC LOW↵ 5 MIDDLE↵ HIGH↵ OFF DNR 6 LOW MIDDLE HIGH (with AGC in OFF mode) SENS-UP OFF 7 AUTO! (with LENS in MANUAL mode or SHUTTER in FLX mode) SPECIAL CAMERA ID 8 DAY/NIGHT SYNC MOTION DET PRIVACY MIRROR EXIT MENU SHARPNESS RES
ملخص المحتوى في الصفحة رقم 17
SETUP Menu Menu Item Option Description LENS DC! Selects Lens type. Only DC mode is supported at this time. VIDEO MANUAL Caution Selecting VIDEO or MANUAL adversely affects camera operation. SHUTTER FLK Adjusts shutter settings. MANUAL! FLK (Flickerless) reduces on-screen flickering. ESC! MANUAL adjusts the shutter speed from 1/60-1/120,000 of a second (NTSC) or 1/50-120,000 of a second (PAL). Not available in DC lens mode. ESC (Electronic Shutter Control) adjusts the brightness level on scree
ملخص المحتوى في الصفحة رقم 18
SPECIAL Menu On the main SETUP menu: 1. Press UP or DOWN and then select SPECIAL. 2. Push SETUP (MENU) to access the SPECIAL menu. Menu Item Option Description CAMERA ID OFF Turns ID display off and on. To add a camera title (name and/or number) to 1 ON be displayed on the screen, see Adding a Camera Title Display. DAY/NIGHT AUTO When set to AUTO , the camera automatically switches to Night mode 2 COLOR (B/W) when the light level is low. BW When set to COLOR, the camera stays in Day mode (Co
ملخص المحتوى في الصفحة رقم 19
Adding a Camera Title Display On the SPECIAL menu, select CAMERA ID, then press SETUP (MENU).. 1. Press the menu control UP, DOWN, LEFT, or RIGHT CAMERA ID to select a character, then press (SETUP) MENU to A B C D E F G H I J K L M accept it. The character is saved and the title cursor N O P R Q S T U V W X Y Z at the bottom of the screen moves to the next a b c d e f g h i j k l m position. Use the # $ symbols to go backward or n o p q r s t u v w x y z – . 0
ملخص المحتوى في الصفحة رقم 20
Motion Detection Setup On the SPECIAL menu, select MOTION DET, then press SETUP (MENU). MOTION DETECTION Menu Item Option Description AREA SEL AREA 1 Select which of the four motion AREA SEL AREA 1 AREA 2 detection grids top left, top right, AREA STATE ON TOP |..|................| 10 AREA 3 bottom left, bottom right) you would DOWN |........|..........| 25 AREA 4 like to modify. LEFT |...|...............| 20 AREA ON Choose whether to activate or RIGHT |........|..........| 40 STATE OFF deacti
