ملخص المحتوى في الصفحة رقم 1
P3PC-1132-07ENZ0
5000N
Operator's Guide
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
CONTENTS INTRODUCTION............................................................................. v ■ Regulatory Information ......................................................... v ■ Note, Liability ........................................................................ vi ■ Safety Precautions ................................................................ x Chapter 1 Overview of fi-5000N ............................................... 1 1.1 Overview.......................................
ملخص المحتوى في الصفحة رقم 4
3.7 Pull Mode User Authentication Settings ........................ 21 3.8 Push Mode Automatic Logout Time Settings ................ 23 3.9 Host Connection Time-out............................................... 24 3.10 Displaying Device Information ....................................... 25 3.11 Initialization of fi-5000N................................................... 26 Chapter 4 Installing and Setting Driver................................. 27 4.1 Installing FUJITSU TWAIN 32 Scanner Drive
ملخص المحتوى في الصفحة رقم 5
Chapter 6 User Authentication ..............................................69 6.1 Fingerprint Registration................................................... 70 6.2 User Authentication by Fingerprint ................................ 74 6.3 User Authentication by PIN ............................................ 75 6.4 Changing the User’s PIN.................................................. 76 Chapter 7 Daily Care............................................................... 77 7.1 Cleaning Mat
ملخص المحتوى في الصفحة رقم 6
iv
ملخص المحتوى في الصفحة رقم 7
INTRODUCTION Thank you for purchasing the fi-5000N. This document describes how to handle fi-5000N and basic operation methods. Before you start using it, be sure to thoroughly read this manual to ensure a correct use. ■Regulatory Information FCC Declaration This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resident
ملخص المحتوى في الصفحة رقم 8
Bescheinigung des Herstellers / Importeurs Für den fi-5000N wird folgendes bescheinigt: •In Übereinsstimmung mit den Bestimmungen der EN45014(CE) funkentstört •Maschinenlärminformationsverordnung 3. GPSGV: Der höchste Schalldruckpegel beträgt 70 dB (A) oder weniger, gemäß EN ISO 7779. ■Note, Liability BEFORE USING THIS PRODUCT, PLEASE READ THIS MANUAL CAREFULLY. IF THIS PRODUCT IS NOT USED CORRECTLY, UNEXPECTED INJURY CAN OCCUR TO USERS OR BYSTANDERS Keep this manual in a safe place so that i
ملخص المحتوى في الصفحة رقم 9
The Authentication Data may be categorized as personal data and may be subject to various data protection and privacy laws. You are responsible for ensuring all use is in compliance with all such applicable laws. THE RELIABILITY OF THE FINGERPRINT AUTHENTICATION TECHNOLOGY AND THE MEASURES USED TO PROTECT THE AUTHENTICATION DATA, SUCH AS ENCRYPTION, ARE NOT GUARANTEED ALWAYS TO BE EFFECTIVE AND ACCURATE, OR WITHOUT ERROR. YOU USE THE FINGERPRINT TECHNOLOGY AUTHENTICATION AT YOUR OWN RISK.
ملخص المحتوى في الصفحة رقم 10
Manufacturer PFU LIMITED International Sales Dept., Imaging Business Division, Products Group Solid Square East Tower, 580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Japan Phone: (81-44) 540-4538 All Rights Reserved, Copyright© PFU LIMITED 2004-2009 About Maintenance The user must not perform repairs on this device. Contact the store where you purchased it or an authorized FUJITSU Image Scanner service provider to have repairs done on this product. Warning Indications Used In This
ملخص المحتوى في الصفحة رقم 11
Screen Examples In This Manual The screen examples in this manual are subject to change without notice in the interest of product improvement. If the actual displayed screen differs from the screen examples in this manual, operate by following the actual displayed screen while referring to the User's Manual of the device application you are using. The screenshots in this manual were captured from the FUJITSU TWAIN32 device driver, ScandAll 21 Image Capturing Utility Software, fi-5000N Softwa
ملخص المحتوى في الصفحة رقم 12
■Safety Precautions Do not damage the AC cable. A damaged AC cable may cause fire or electric shock. Do not place heavy objects on AC cables, or pull, bend, twist, heat, damage or modify AC cables. Do not use damaged AC cables or power plugs, or install any cables or power plugs to loose wall sockets. Use only specified AC cables and connector cables. Use only specified AC cables and connector cables. Failure to use the correct cables might cause electric shock and/or equipment failure. Do n
ملخص المحتوى في الصفحة رقم 13
Turn the device OFF if it is damaged. If the device is damaged for any reason, turn the device off and unplug the power cable. Contact the store where you purchased the device. Do not put liquids inside the device. Do not insert or drop metal objects in/on to the device. Do not splash or allow the device to get wet. If foreign objects (water, small metal objects, liquids, etc.) get inside the device, imme- diately turn off the device and disconnect the power plug from the power outlet. Then,
ملخص المحتوى في الصفحة رقم 14
Do not install the device on unstable surfaces. Make sure that the device is installed on a flat, level surface and that none of its parts extend beyond the surface top, such as a desk or table. Do not install the device on unstable surfaces. Install the device on a level surface that is free of vibration to prevent it from falling. Install the device on a strong surface that will support the weight of the device and other devices. Do not place heavy objects or stand on top of the devic
ملخص المحتوى في الصفحة رقم 15
Disconnect the power plug from the power outlet when the device is not used for a long period of time. When the device is not going to be used for a long period of time, be sure to disconnect the power plug from the power outlet. Do not install the device in direct sunlight. Do not install the device under direct sunlight or near heating apparatus. Doing so might cause excessive heat to build up inside the device, which can cause device trouble or even fire. Install the device in a well-vent
ملخص المحتوى في الصفحة رقم 16
xiv
ملخص المحتوى في الصفحة رقم 17
Chapter 1 Overview of fi-5000N 1 1.1 Overview ............................................................................................................. 2 1.2 Features .............................................................................................................. 3 1.3 Examples of Operation ...................................................................................... 4 fi-5000N Operator’s Guide 1
ملخص المحتوى في الصفحة رقم 18
1.1 Overview The function of the fi-5000N is to connect a fi-series scanner to a computer through the network. This framework is shown in the diagram below. This framework is referred to as the fi-5000N sys- tem hereinafter. Scanner fi-5000N Network Computer This device connected to a fi-series scanner through the USB interface, can transmit scanned images to a computer over networks. The fi-5000N makes it possible to scan documents without touching a computer at sites where scanning documen
ملخص المحتوى في الصفحة رقم 19
Overview of fi-5000N 1.2 Features 1.2 Features 1. Simple and secure operator identification with fingerprint authentication With the fingerprint authentication technology, the user can be easily identified by a touch of a finger. There is no need for special hardware or personal identification numbers that in the majority of cases. 1 2. High-speed scanning and transmission of data via network High speed scanning and high speed data transmission via a network becomes a reality with the utiliza
ملخص المحتوى في الصفحة رقم 20
1.3 Examples of Operation There are two ways to perform scanning documents using fi-5000N. 1. Pull mode scanning Computer with scanning application scan the documents from the scanner on the network and capture the image data. This is called Pull mode because the image data is pulled from the scanner to the computer via the network. In this mode, you can specify if user authentica- tion process is enabled. If enabled, fi-5000N enter into user authentication waiting state when scanning is init
