ملخص المحتوى في الصفحة رقم 1
OPERATING INSTRUCTIONS AND PARTS LIST
INSTRUCCIONES DE OPERACIÓN Y LISTA DE PIEZAS
MC18
Concrete Saw
MODELS: MC1809R (9 HP ROBIN)
MC1809H (9 HP HONDA)
MC1813R (13.5 HP ROBIN)
MC1813H (13 HP HONDA)
MC1805G (5 HP GAST)
MC1805B (5 HP BALDOR)
Model:
Serial Number:
Engine Serial No.:
Purchase Date:
17400 West 119th Street
Olathe, Kansas 66061
Customer Service ..... 800-288-5040
Corp. Office ...............913-928-1000
Cust. Service FAX ....800-825-0028
0A7859
Corp. Office FAX .......913-438-7951
Cop
ملخص المحتوى في الصفحة رقم 2
EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. EACH MACHINE IS SUPPLIED WITH A COPY OF THIS MANUAL. OPERATORS OF THIS EQUIPMENT MUST READ AND BE FAMILIAR WITH THE SAFETY WARNINGS. FAILURE TO OBEY WARNINGS MAY RESULT IN INJURY OR DEATH. FOLLOW INSTRUCTIONS STRICTLY TO ENSURE LONG SERVICE IN NORMAL OPERATION. CONTENTS Symbol Definitions .................................................................................................................................4 - 6 Decal De
ملخص المحتوى في الصفحة رقم 3
NOTE: NOTA: 3
ملخص المحتوى في الصفحة رقم 4
Symbol Definitions Definición De Simbolos • Please Read The Instructions For Use Prior To Operating The Machine For The First Time. • Antes De La Puesta En Marcha, Lea Detenidamente Las Instrucciones Y Familiaricese Con La Máquina. • Mandatory • Obligatorio • Indication • Indicación • Prohibition • Prohibición • Warning Triangle • Triángwulo De Advertencia • Wear Eye Protection • Usar Gafas De Protección • Wear Head Protection • Usar Casco De Protección • Wear Breathing Protection • Usar Másca
ملخص المحتوى في الصفحة رقم 5
• Do Not Use In Flammable Areas • No Usar In Áreas Inflamables • Machinery Hazard, Keep Hands And Feet Clear • Máquina Peligrosa - Mantenga Manos Y Pies Alejados De La Máquina • Danger, Poison Exhaust Gas • Peligro, Gas De Escape Venenoso • No Non-working Personnel In Area • Prohibido Para Personas Ajenas A La Obra • No Smoking • No Fumar • Do Not Operate Without All Guards In Place • No Operar Sin Todas Las Protecciones In Su Sitio • Always Keep the Blade Guards In Place • Mantenga Siempre Las
ملخص المحتوى في الصفحة رقم 6
• Repairs Are To Be Done By An Authorized Dealer Only • Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado • Diamond Blade • Sierra Diamantada • Blade Diameter • Diámetro De La Hoja • Pulley Diameter • Diámetro De La Correa • Number of Revolutions Per Minute, Rotational Speed • N° De Revoluciones Por Minuto, Velocidad De Rotación • Blade Flange Diameter • Diámetro De La Brida De La Hoja • Machine Mass (lbs) • Masa De La Máquina (lbs) • Electric Motor • Motor eléctric
ملخص المحتوى في الصفحة رقم 7
DECAL DESCRIPTIONS AND LOCATIONS DECRIPCIÓN DE CALCAMONIAS Y UBICACIONES P/N 189732 Location: Front of Frame (All Models) Quantity: 1 P/N 189731 Location: Blade Guard (All Models) Quantity: 1 P/N 174993 Location: Belt Guard (All Models) P/N 187691 Quantity: 1 Location: Frame (All Models) Quantity: 1 P/N 174998 Location: Top of Screw Feed Bracket (Screw Feed Model Only) Quantity: 1 P/N 139633 Location: Front of Handle Support (E-Z Tilt Model Only) Quantity: 1 P/N 177588 Location: Top of Bel
ملخص المحتوى في الصفحة رقم 8
NOTE: NOTA: 8
ملخص المحتوى في الصفحة رقم 9
MC 18 Specifications Power Source Gas Pneumatic Electric MC 18 Model MC 18 9R MC 18 9H MC 18 13.5R MC 18 13H MC 18 5A MC 18 5E Horsepower 9 HP 9 HP 13.5 HP 13 HP 5 HP 5 HP (230 V) Standard Model C00094 C00084 C00098 C00086 C00088 C00090 C00095 Screw Feed Model C00085 C00099 C00087 C00089 C00091 ALL SAWS FEATURE: Max. Blade Cap. in. (mm) 18 (450) 18 (450) 18 (450) 18 (450) 18 (450) 18 (450) Max. Depth of Cut 4-5/8"-6-5/8" (117.5-168.3mm) Blade Shaft RPM 2,600 2,600 2,600 2,600 2,500 1,800 Weight
ملخص المحتوى في الصفحة رقم 10
SAFETY FIRST! WARNINGS DO’s and DO NOT’s WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. DO DO read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. DO keep all guards in place and in good condition. DO wear safety approved hearing, eye, head and respiratory protection. DO read and understand all warnings and instructions on the machine. DO read and underst
ملخص المحتوى في الصفحة رقم 11
SAFETY FIRST! WARNINGS DO’s and DO NOT’s WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. DO NOT DO NOT operate this machine unless you have read and understood this operator’s manual. DO NOT operate this machine without the blade guard, or other protective guards in place. DO NOT stand behind or in front of the blade path while the engine/motor is running. DO NOT leave this machine unattended while the engine/motor is
ملخص المحتوى في الصفحة رقم 12
FIGURE 1 FIGURE 2 2H 2B 2 I 2F 2A 2D 2E 2A. BLADE SHAFT NUT: Use to tighten the outer flange against the diamond blade. 2B. OUTER FLANGE: Use to hold the diamond blade in position. 2C. NOT USED 2D. LOCKING PIN: Use to prevent the diamond blade from rotating on the shaft during operation. 2E. DIAMOND BLADE: Use as the cutting tool for concrete and asphalt surfaces. 2F. INNER FLANGE: Inside support used to hold the dia- mond blade in position. 2G. NOT USED 1A. WATER VALVE: Use to contr
ملخص المحتوى في الصفحة رقم 13
PRE OPERATION CHECKLIST Before leaving our factory, every machine is thoroughly tested. Follow our instructions strictly and your machine will give you long service in normal operating conditions. Before starting up the machine, make sure you read this entire operations manual and are familiar with the operation of the machine. WITH MACHINE COLD AND SETTING LEVEL: 1. Check engine oil. Fill to full mark on dip stick with 10W30 oil. DO NOT OVERFILL!! • Gas Models: Class MS, SD, SE or better. 2
ملخص المحتوى في الصفحة رقم 14
INDICATION 2 Assembly MANDATORY INFORMATION INSTRUCTION • The Handle must be attached. Place Handle in position and securely tighten Knobs. PROHIBITION • Check the engine oil level. Service before using. Refer WARNING to the engine operation manual for detailed information. 3 General Instructions These signs will give advice for your safety Remove the Blade (2E) before transport. Before leaving our factory every machine is thoroughly tested. WARNING: DO NOT operate without the proper blade
ملخص المحتوى في الصفحة رقم 15
6 Starting The Power Source 4 Check Before Starting Always pay extreme care and attention to the preparation of the machine before starting. Remove all wrenches and tools from the floor and the machine. Take into account the working conditions from the health and safety point of view. Always keep blade guard and transmission guard in place. FUEL: Check the engine maintenance manual. * Gas Models: Unleaded gasoline is recommended. • Check that the engine oil level is correct. Because the On Gas
ملخص المحتوى في الصفحة رقم 16
Test for adequate water supply [2-1/2 to 5 gal/ WARNINGS!!! min (10 to 20 lit./min)]. Low water flow will cause damage to diamond blades. DO turn the “ON/OFF” switch to the “OFF” position prior If water supply is interrupted, stop cutting to connecting the machine to the power source. immediately. DO make sure electric powered machines are plugged into a properly grounded circuit. Screw Feed Version: DO make sure power cords are the proper size and in • Lower the blade into the cut by pulling u
ملخص المحتوى في الصفحة رقم 17
10 Maintenance BLADE SHAFT V-BELTS: This concrete saw is equipped with “3VX” premium V-belts. Before performing any maintenance, ALWAYS These belts are properly tensioned at the factory. Severe park the machine on a level surface with the damage or breakage of the crankshaft can occur if the belts Engine OFF and the Engine Switch in the "OFF" are tensioned too tightly. Check the belt tension as set on position. the new saw and NEVER set belts beyond the original tension. Not enough tension wil
ملخص المحتوى في الصفحة رقم 18
12 Governor Speed 13 Repairs It is critical that the Governor and throttle on all internal We carry out all repairs in the shortest possible time and at combustion engines be adjusted properly. The engine speed the most economical prices. (See front page for our address is preset at the factory for the proper sawing speed. It is and phone numbers.) NOT normally necessary to change this setting. It should be periodically verified after the saw is placed into service. To 14 Service Parts change
ملخص المحتوى في الصفحة رقم 19
NOTE: NOTA: 19
ملخص المحتوى في الصفحة رقم 20
Diagram 1 – Frame & Axle 20
