ملخص المحتوى في الصفحة رقم 1
1
7 ⁄4" CIRCULAR SAW
MODEL G9906
INSTRUCTION MANUAL
COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA
ملخص المحتوى في الصفحة رقم 2
1 G9906 7 ⁄4" Circular Saw -2-
ملخص المحتوى في الصفحة رقم 3
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. Remember that safety messages by them- selves do not eliminate danger and are not a substitute for proper accident pre- vention measures. Indica
ملخص المحتوى في الصفحة رقم 4
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD 14. MAINTAIN TOOLS WITH CARE. for the tool. Make sure your exten- Keep tools sharp and clean for best sion cord is in good condition. and safest performance. Follow Conductor size should be in accor- instructions for lubricating and dance with the chart below. The changing accessories. amperage rating should be listed on 15. DISCONNECT TOOLS before ser- the motor or tool nameplate. An vicing and changing accessories, undersized cor
ملخص المحتوى في الصفحة رقم 5
INTRODUCTION Commentary We are proud to offer the Grizzly Model The specifications, details, and pho- G9906 Circular Saw. The Model G9906 is tographs in this manual represent the part of a growing Grizzly family of fine Model G9906 as supplied when the manu- power tools. When used according to the al was prepared. However, owing to guidelines set forth in this manual, you can Grizzly’s policy of continuous improve- expect years of trouble-free, enjoyable ment, changes may be made at any time ope
ملخص المحتوى في الصفحة رقم 6
OPERATIONS Before You Start Setting the Edge Guide 1. Loosen the edge guide set knob Please take the time to familiarize yourself with the controls of your new saw. Below located on the top leading edge of are listed the names of controls and fea- the saw base. tures found on the saw. Please refer to 2. Insert the edge guide in the slot just Fig. 1 below the retaining screw. 3. Slide the edge guide until it is insert- ed through a slot provided on the left FIG 1 hand side of the saw base. Dust
ملخص المحتوى في الصفحة رقم 7
OPERATIONS, CONT’D Guide Notches Operating the Saw 1. Ensure the blade is secure. The saw is provided with two guide notch- es for either 45° or 90° cuts. These are 2. Grasp the hand grip with one hand. located on the leading edge of the saw Use the hand you would use most base. The notches are used for following a often: if you are right handed use the line through a cut. It should be noted that right. these are provided for one blade thickness. 3. Grasp the stabilizing hand grip with Blades w
ملخص المحتوى في الصفحة رقم 8
OPERATIONS, CONT’D Changing Blades MAKE SURE SAW IS UNPLUGGED! 1. Rotate the blade guard clockwise to reveal the blade. 2. While holding the blade guard open, place the saw onto a secure surface engaging the blade teeth onto the surface. 3. While maintaining downward pres- sure on the saw, remove the retaining screw and washer from the center of the blade. 4. Note the orientation of the teeth. They are pointed toward the leading edge base of the saw. Be careful to avoid touching the saw teeth a
ملخص المحتوى في الصفحة رقم 9
OPERATING TIPS AND MAINTNENACE Guidelines and Tips Maintenance Avoid overloading the saw. Always use Keep the saw free from dirt and grease. sharp saw blades. Do not apply excessive pressure to the saw while using. If the speed drops abnormally, decrease pressure immediately. If Disassembly and improper reassem- the blade stops abruptly or becomes bly of this device can result in electri- jammed, release the trigger at once. cal shock danger. Always have this Ensure the safety of the workplace
ملخص المحتوى في الصفحة رقم 10
NOTES
ملخص المحتوى في الصفحة رقم 11
NOTES 1 G9906 7 ⁄4" Circular Saw -9-
ملخص المحتوى في الصفحة رقم 12
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are here- by limited to
ملخص المحتوى في الصفحة رقم 13
WARRANTY CARD Name__________________________________________________________ Street__________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ Model # G9906 Circular Saw Order #_______________________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is strictly c
ملخص المحتوى في الصفحة رقم 14
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE 1 -12- G9906 7 ⁄4" Circular Saw
