ملخص المحتوى في الصفحة رقم 1
Read
Cooper Bussmann
and Retain
BU-905U-L-T Transmitter
for Future
Quick Start Guide
Reference
Version 1.8
3A1577Rev1.8
ملخص المحتوى في الصفحة رقم 2
Cooper Bussmann BU-905U-L-T Transmitter Quick Start Guide About this Document This document is the Cooper Bussmann BU-905U-L-T Wireless I/O Transmitter Unit Quick Start Guide and contains the following sections: Section Read this section if you want to … Basic steps for using your unit Learn the basic steps for installing and using your unit. Factory default configuration Understand how the transmitter sends information to the receiver. Unit components Understand the different parts of your unit
ملخص المحتوى في الصفحة رقم 3
Cooper Bussmann BU-905U-L-T Transmitter Quick Start Guide Unit Components and Connections Your BU-905U-L-T Transmitter unit has the following components and terminal connections: IMPORTANT ELECTRICAL SAFETY INFORMATION In order to comply with Electrical Safety Regulations, this module must be installed in an Electrical AND Fire enclosure. This enclosure may be a single or multiple enclosures. Access to the module is to be made by a Service Person only. 3A1577Rev1.8 www.cooperbussmann.com/Bussman
ملخص المحتوى في الصفحة رقم 4
Cooper Bussmann BU-905U-L-T Transmitter Quick Start Guide Front Panel Components SMA Antenna Connector at Top of Unit Indicator LEDs RS232 Configuration Port Rotary Switch for Setpoint Settings The triangle on the rotary switch indicates the current position, for example: NOTE: To avoid damaging the rotary switch, use a screwdriver to change the position. The rotary switch uses the following setpoint levels: Position Lower Level (mA) Upper Level (mA) 1 4.8 6.4 2 6.4 8.0 3 8.0 9.6 4 9.6 11.2 5 11
ملخص المحتوى في الصفحة رقم 5
Cooper Bussmann BU-905U-L-T Transmitter Quick Start Guide The LEDs on the front panel indicate the unit status: LED Status Indicates None No power supply. OK LED Green Current status of the unit OK. OK LED Red Fault condition detected in unit. TX LED Flashes Transmitting Message. PG LED on Configuration Cable Connected. Input LED ON Input LEDs (i.e., D1,D2, SP, AZ.) light when the corresponding input is active. D1 Digital Input 1 is active (Low). D2 Digital Input 2 is active. SP Analog Setpoint
ملخص المحتوى في الصفحة رقم 6
Cooper Bussmann BU-905U-L-T Transmitter Quick Start Guide Resetting Your Unit to Factory Defaults To reset the default factory configuration: 1. Set the RSSI rotary switch to position 0 using a screwdriver. 2. Power on the BU-905U-L-T transmitter. 3. The BU-905U-L-T transmitter flashes all LEDs at medium flash (i.e., 1.6Hz). NOTE: If the LEDs do not flash, you must repeat steps 1 and 2 until the LEDs flash before continuing. 4. Set the RSSI rotary switch to another position (i.e. position 1) wit
ملخص المحتوى في الصفحة رقم 7
Cooper Bussmann BU-905U-L-T Transmitter Quick Start Guide Industry Canada: BU-905U-L Wireless I/O Module RSS-119 - This device has been type accepted for operation by Industry Canada in accordance with RSS-119 of the Industry Canada rules. See the label on the unit for the specific Industry Canada certification number and any other certification designations. NOTE: Any changes or modifications not expressly approved by Cooper Bussmann P/L could void the user’s authority to operate this equipment
ملخص المحتوى في الصفحة رقم 8
Customer Assistance Customer Satisfaction Team Application Engineering Available to answer questions regarding Cooper Technical assistance is available to all customers. Bussmann products & services Monday-Friday, Staffed by degreed engineers, this application support 8:00 a.m. – 4:30 p.m. for all US time zones. is available Monday-Friday, 8:00 a.m. – 5:00 p.m. CT Contact: Contact: Toll-free phone: 855-287-7626 (855-BUSSMANN) Phone: 636-527-1270 Toll-free fax: 800-544-2570 Fax: 636-527-1607
