ملخص المحتوى في الصفحة رقم 1
K
L
E
T
I
R
S
SWR - SWC - SWD
Swing Gate Operator
Installation Guide
CM
C US
Operator models contained in this manual
conform to UL325 standard for use in
Class I, II, III, and IV applications
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
T
E
E
T
D
N
I
ملخص المحتوى في الصفحة رقم 2
Table of Contents Pre-installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Open Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Before You Begin... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Reverse Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Always Check the Gate’s Action . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Sh
ملخص المحتوى في الصفحة رقم 3
Pre-installation Information Safety Information and Warnings THE FOLLOWING FORMATS ARE USED FOR SAFETY NOTES Before You Begin... IN THESE INSTRUCTIONS. Before unpacking, inspect the carton for exterior damage. If CAUTION you fi nd damage, advise the delivery carrier of a potential This type of warning note is used to claim. Inspect your package carefully. You can check your indicate the possibility of damage to the accessory box parts with the enclosed packing slip for your gate or gate o
ملخص المحتوى في الصفحة رقم 4
MODEL SWR POWER WIRING Wiring Specifi cations MAXIMUM DISTANCE (FEET) VOLTS & HP WIRE GAUGE Refer to the following steps for details on power and SINGLE DUAL 316 158 12 accessory wiring for the operator. 502 251 10 115 VOLTS 800 400 8 WARNING 1/2-HP 1272 636 6 ALL AC ELECTRICAL CONNECTIONS TO THE POWER SOURCE AND 2022 1011 4 THE OPERATOR MUST BE MADE BY A LICENSED ELECTRICIAN 764 382 12 1218 609 10 AND MUST OBSERVE ALL NATIONAL AND LOCAL ELECTRICAL 230 VOLTS 1936 968 8 CODES. 1/2-HP 3076 1538
ملخص المحتوى في الصفحة رقم 5
Mounting Pad Installation WARNING The operator is intended for installation only on gates used for The gate operator mounts bolted to a custom poured vehicles. Pedestrians must be supplied with a separate access concrete mounting pad. The pad supports the operator and opening. The pedestrian access opening shall be designed to prevents it from twisting during operation. promote pedestrian usage. Locate the gate such that persons An optional post mount kit is also available (P/N 2120-483)
ملخص المحتوى في الصفحة رقم 6
GEAR Operator Preparation REDUCER Vent Plug Installation In order to keep gear oil from spilling out during shipping, REMOVE THE SOLID PLUG gear reducers used in gate operators have either a solid WITH AN ALLEN plug, or a sealed vent plug, installed at the factory. WRENCH For operators with a solid plug, replace the solid plug with the vent plug provided (see Figure 2). With the vent plug installed, remove the vent plug’s breather pin to allow the gear box to vent (see Figure 2). INSTALL THE
ملخص المحتوى في الصفحة رقم 7
Gate Arm Installation (Cont.) GATES SHOWN OPEN Choosing Good Harmonics Good harmonics are necessary to minimize wear and tear on the operator. The gate will have smoother starts and stops GOOD BAD when the arm is installed with good harmonics. Figure 5 HARMONICS HARMONICS! shows an example of good and bad arm harmonics. Installing the Gate Arm on the Operator The hex cap screws (see Figure 6) in the side of the crank assembly are shipped loose for placement on the operator drive shaft. Once
ملخص المحتوى في الصفحة رقم 8
Operator Setup LIFT UP ON TAB Controller Access The Controller in models SWR, SWC and SWD is hinged for access and can be removed without taking off the operator’s CONTROLLER SWINGS DOWN cover. It swings down for installation, programming, and troubleshooting access (see Figure 8). Under most circumstances you will not need to remove the Controller. To access the Controller, lift the metal tab below the AC power switch and swing the Controller down. The Controller is protected by a plastic
ملخص المحتوى في الصفحة رقم 9
Operator Setup (Continued) LIMIT Limit Cam Rough Adjustment SWITCHES (2) RIGHT-HAND INSTALLATION The limit cams are not preset at the factory and must TOP CAM - OPEN LIMIT be adjusted for each installation. The limit switches are BOTTOM CAM - CLOSE LIMIT activated by two rotating limit cams attached to the drive shaft (see Figure 10). The Controller is factory set for right LEFT-HAND INSTALLATION hand installations. The top cam is for OPEN and the bottom TOP CAM - CLOSE LIMIT cam is for CLO
ملخص المحتوى في الصفحة رقم 10
Controller Features WHIP ANTENNA ANTENNA CONNECTOR OPERATION AND POWER OPERATION PROGRAMMING INDICATORS BUTTONS INDICATORS DISPLAY PROGRAMMING SOLAR BUTTONS PANEL TERMINALS INPUT POWER MOTOR TERMINALS BOARD COVER ACCESSORY POWER BATTERY TERMINALS TERMINALS RESET BUTTON TERMINALS PLUG-IN LOOP PRIMARY/ DETECTOR SECONDARY CONNECTORS COMM LINK TERMINALS SINGLE INPUT TERMINALS FIRE DEPT INPUT TERMINALS OPEN INPUT TERMINALS 3-BUTTON SHADOW/RESET STATION TERMINALS AUXILIARY OPEN AND CLOSE REVERSE LOOP
ملخص المحتوى في الصفحة رقم 11
Indicator Descriptions INDICATOR DEFINITION INDICATION WHEN LIT INDICATION WHEN LIT DURING NORMAL OPERATION DURING PROGRAMMING OPERATION PROGRAMMING 24 VOLT INPUT LOW VOLTAGE AC POWER IS PRESENT POWER 24 VOLT DC LOW VOLTAGE DC POWER IS PRESENT ACCY POWER OPEN SIGNAL PRESENT FROM THE INTERNAL OPEN RECEIVER OR AN EXTERNAL DEVICE CONNECTED TO THE OPEN INPUT TERMINAL CLOSE SIGNAL IS PRESENT FROM A DEVICE CLOSE CONNECTED TO THE CLOSE INPUT TERMINAL STOP INPUT TERMINAL IS OPEN AND STOP NOT CONNE
ملخص المحتوى في الصفحة رقم 12
Terminal Descriptions TERMINAL GROUP FUNCTION AC N FACTORY CONNECTED TO 24 VAC FROM TRANSFORMER OR 24 VOLT INPUT 24 VDC FROM CONTINUOUS DUTY DC SUPPLY. AC DC - ACCESSORY POWER PROVIDES 24 VOLT DC POWER FOR ACCESSORIES. DC + RESET RESET BUTTON FACTORY CONNECTED TO THE CONTROLLER’S RESET BUTTON. COMMON C B COMM LINK FOR 3-WIRE NETWORK CONNECTION TO SECOND OPERATOR IN DUAL GATE INSTALLATIONS. A COMMON CONNECT TO NORMALLY OPEN SWITCH FOR SINGLE BUTTON OPERATION. ALTERNATES SINGLE BUTTON INPUT BETW
ملخص المحتوى في الصفحة رقم 13
Operator Accessory Connections 3-BUTTON STATION PHOTOEYE FOR REVERSE TELEPHONE ENTRY KEYPAD PHOTOEYE FOR CLOSE OBSTRUCTION KEYSWITCH FIRE ACCESS SWITCH SOLENOID LOCK EXTERNAL POWER PHOTOEYE FOR OPEN OBSTRUCTION SINGLE-CHANNEL RADIO RECEIVER MAGLOCK GATE EDGE SENSOR FOR REVERSE TWO-CHANNEL RADIO RECEIVER WARNING STROBE OR AUDIBLE SOUNDER CHANNEL #1 WIRELESS GATE EDGE SENSOR OPEN/CLOSE MGT TRANSMITTER Figure 13. Operator Accessory Connections SWR • SWC • SWD Swing Gate Operator Installation Guide
ملخص المحتوى في الصفحة رقم 14
Basic Controller Programming Programming Overview PROGRAM The Controller can be programmed with various options for the operator. INDICATOR The programming fi elds are defi ned as “functions” that have “options”. DOWN AND UP To make setup easier for the installer, the Controller’s programming is divided into two groups: basic and advanced. The basic programming PRESS DOWN AND UP PROGRAM INDICATOR group contains the functions commonly used in most swing gate BUTTONS TOGETHER WILL LIGHT WHEN SYS
ملخص المحتوى في الصفحة رقم 15
Basic Controller Programming (Cont.) FUNCTION OPTIONS Run Alarm and Pre-start Alarm RUN ALARM OFF "RP" The factory default is Run Alarm on and a 3-second Pre-start Alarm. The PRE-START ALARM OFF operator’s beeper will sound 3 seconds before the operator starts. The options are: RUN ALARM ON PRESS UP OR PRE-START ALARM OFF DOWN TO CYCLE � Run Alarm Off and Pre-start Alarm Off THROUGH OPTIONS � Run Alarm On and Pre-start Alarm Off RUN ALARM ON PRESS ENTER TO � Run Alarm On and Pre-start Alarm On
ملخص المحتوى في الصفحة رقم 16
Advanced Controller Programming FUNCTION OPTIONS Entering Advanced Programming Mode ADVANCED PROGRAMMING FUNCTIONS "AD" To access and program the Advanced Programming functions, for each WILL NOT BE DISPLAYED programming session, Advanced Programming must be enabled. ADVANCED PROGRAMMING OPTIONS After exiting programming, the Advanced Programming functions WILL BE DISPLAYED will be available on the programming display during the next programming session unless the operator has run 50 or more
ملخص المحتوى في الصفحة رقم 17
Advanced Controller Programming (Cont.) FUNCTION OPTIONS Auxiliary Relay Mode AUXILIARY RELAY DISABLED "AR" The Auxiliary Relay has normally open and normally closed contacts. The factory setting disables the Auxiliary Relay. The relay can be set for: AUXILIARY RELAY USED FOR MAGLOCK CONTROL � Maglock: The relay will energize during any pending or actual gate PRESS UP OR DOWN TO CYCLE motion (open only), to deactivate a magnetic or solenoid gate lock. AUXILIARY RELAY USED FOR THROUGH OPTIONS T
ملخص المحتوى في الصفحة رقم 18
Advanced Controller Programming (Cont.) FUNCTION OPTIONS Soft Start/Stop Duration SOFT START DISABLED "SS" This function is only used with DC swing gate Model SWD. This function causes the operator to start and stop the DC motor slowly reducing gate wear and tear (at the full open or closed positions only). SET SOFT START DURATION TIME FROM 1 TO 10 SECONDS The factory default sets the Soft Start/Stop Duration to 3 seconds. The Soft Start/Stop Duration can be set from 1 to 10 seconds. PRESS UP
ملخص المحتوى في الصفحة رقم 19
Advanced Controller Programming (Cont.) FUNCTION OPTIONS Radio Enable "RA" INTERNAL RADIO RECEIVER DISABLED ® The Controller contains a built-in MegaCode radio receiver to allow activation from up to 40 access control transmitters and two Model MGT (gate edge) transmitters. The factory default enables the internal radio INTERNAL RADIO RECEIVER ENABLED receiver. Alternately, the internal receiver can be disabled. PRESS UP OR Antenna Installation DOWN TO CYCLE THROUGH OPTIONS The Controller is
ملخص المحتوى في الصفحة رقم 20
Loop Layout Illustration SWR • SWC • SWD Swing Gate Operator Installation Guide - 18 - 227965 Revision X13 3-28-2008 2" MAX. USE RELIEF CUTS 3/8" AT CORNERS WALL PARTIALLY TWIST WIRE FROM END OF SHOWN FOR CLARITY LOOP LOOPS BACK TO OPERATOR SEALANT AT LEAST SIX TIMES PER FOOT 2" MULTIPLE TURNS REFER TO LOOP INSTALLATION NOTES FOR DETAILS 6 FT. OPEN GATE PARTIALLY SHOWN NOTE: POSITION SHADOW LOOP APPROXIMATELY HALF WAY BETWEEN ENTRY AND EXIT REVERSING LOOPS. THE DISTANCE BETWEEN THE SHADOW LOOP A
