ملخص المحتوى في الصفحة رقم 1
SafewayTM Gate Model G20 for openings 24 3/4” to 43 1/2" wide
Optional 24” extension Model G24 for opening 43 1/2" to 66” wide
Only one extension recommended per gate
User Guide
ملخص المحتوى في الصفحة رقم 2
FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP THEM FOR FUTURE REFERENCE This gate is designed for children from 6 months to 36 months. Since each child’s skills develop at different ages, these age parameters should be monitored against your child’s own development. Gate may be used as a window barrier using the hardware provided. l This product will not necessarily l Intended for use with children prevent all accidents. Never from 6 months through 36 months. leave child unattended. l Check and t
ملخص المحتوى في الصفحة رقم 3
Hinge Side Hardware Locking Side Hardware 1 Stop pin (s) 2 Hinge bottoms (b) L4 1 Locking latch (k) 0 II 2 Hinge spindles with locknuts (c) 1 Locking latch bracket (I) 1 w 2 Springs (d) I 2 Latch spindles with locknut (m) v 2 Hinge caps (e) b 1 Botton locking bracket (p) l!l General Hardware 1 Gate section 8 Wood screws (q) I with 6 bars (h) 1 Protective plastic cover (r) u 1 Gate section with 7 bars (i) 4 Expansion screw sockets (f) u 1 Hinge sid; template (a) 4 Expansion screws (g) f Templates
ملخص المحتوى في الصفحة رقم 4
Important. Gate must be installed in a structurally sound opening. Hinge side of gate must be mounted to a rigid surface. Ensure mounting surface (wall, door frame, stairpost etc.) is strong, rigid and has an even surface. If using gate on a stairway, it must be placed either on top stair or on lowest stair at the bottom. Mounting Hinge Side Screws provided are for mounting directly into wood. If mounting into brick, drywall or other surfaces, use appropriate hard- ware. If installing into hardw
ملخص المحتوى في الصفحة رقم 5
Screw hinge spindles (c) into top and bottom rails of gate section (h) until they are exten- ded equally. These will be adjusted to the correct length at a later stage so do not tighten. Repeat process on gate section (i) using latch spindles (m). Mounting Locking Side Screws provided are for mounting directly into wood. If mounting into brick, drywall or other surfaces, use appropriate hard- ware. If installing into hardwood (i.e. oak), drilling a pilot hole may be necessary. Hold template (j)
ملخص المحتوى في الصفحة رقم 6
As an added safety measure, a stop pin has been provided. Insert stop pin (s) from behind locking latch bracket into hole oppo-site ope- ning direction. Using 2 screws, screw into upper set of screw holes. Correct width will be reached by adjusting gate sections and all four corner spindles. Each spindle adjusts individually and may be extended to varying lengths to allow for mol- ding, uneven walls, etc. Spindles may be extended a minimum of 1” but not more than 3” on each side. Adjust gate sec
ملخص المحتوى في الصفحة رقم 7
Center gate in opening. Gaps on each side should be equal. Place hinge spindles (c) over hinge bottom posts (b), dropping them into place. Adjust latch spindles (m) out until they fit securely into two locking brackets. Latch spindle at top must be adjusted so it clicks under locking latch when in closed position. Space between end of gate and mounting surface should be no less than 1” and not more 3” on each side. Min: 1” Check that gate can be easily opened and Max: 3” closed without catching.
ملخص المحتوى في الصفحة رقم 8
A protective plastic cover (r) is provided for top latch spindle. Cut cover, remove latch spindle and put cover on. Return spindle and adjust to correct length. I I 1 I I I I I I 8
ملخص المحتوى في الصفحة رقم 9
To open gate, press down on locking latch with thumb, lift gate and slide out of upper and lower locking brackets. Note. Gate should always be in locked position. If gate is open and excessive pressure is applied, hinge posts are desig- ned to break to prevent structural dama- ge. To lock gate, latch spindle at top must click under locking latch when in closed position. Bottom latch spindle must rest in bottom bracket. * No part of this gate requires lubrication. l Clean by sponging with warm wa
ملخص المحتوى في الصفحة رقم 10
KIDCO LIMITED WARRANTY Your KidCo product is warranted to be free from manufacturing defects for a period of one year from date of purchase under normal use and in compliance with the operating instruc- tions. This warranty extends only to the original retail purchaser and is only valid when sup- plied with proof of purchase. KidCo will either repair, or at our option replace, free of charge, any parts necessary to correct defects in material or workmanship during the warranty period. This warra
