ملخص المحتوى في الصفحة رقم 1
Model PRO 9171FT
InstallationManual
3 Channel Remote Car Starter
Installation Instructions
Forinstallationinvehicleswith12voltnegativegroundcircuits,
gasolineengines,withautomatictransmissiononly!
KITCONTENTS
(1) RemoteStartControlModule
(2) 3ButtonRFKeychainTransmitters
(2) WiringHarnesses
(1) PartsBagContaining
(2) Fuses
(2) FuseHolders
(1) ControlSwitch
(1) ProgrammingSwitch
(1) RingTerminal
(4) 1/2"LongScrews
(1) PinSwitch
(1) Accessory2PinConnector
(1) 2PinDoorLockHarness
(1) RemoteStartWar
ملخص المحتوى في الصفحة رقم 2
The PRO-9171FT is for Automatic Transmission vehicles only! Although it is a sophisticated system, with multiple built-in safety features, it must not be installed into vehicles with manual transmissions. Doing this can cause serious personal injury and property damage. IMPORTANT ! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE 12 PIN INPUT / OUTPUT HARNESS INTO THE REMOTE START CONTROL MODULE UNTIL ALL CONNECTIONS HAVE BEEN MADE TO THE VEHICLE. AFTER SELECTING YOUR TARGET WIRES AS DEFINED BE
ملخص المحتوى في الصفحة رقم 3
LIGHT GREEN Wire : Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch. This wire will show +12 Volts when the ignition key is turned to the RUN or ON position, and in some cases, the START or CRANK position. This wire will show 0 Volts when the key is turned to the OFF and ACCESSORY positions. NOTE: The PRO-9171FT ignition 2 output can be programmed to remain ON while the starter is cranking. The factory default setting for ignition 2 is to show 0
ملخص المحتوى في الصفحة رقم 4
This wire provides a 500 mA + 12 Volt transistorized output when the ignition key is turned to the ON position, and 0 Volts when the ignition key is OFF and when the vehicle is running under the control of the remote starter. This wire should be connected to the ignition input of the alarm system. The Yellow w/ Black wire output will allow you to remote start the vehicle while leaving the alarm armed. (2)WHITEWires:ParkingLightFlasher These wires are the COMMON and NORMALLY OPEN contacts of
ملخص المحتوى في الصفحة رقم 5
DARKGREENWire:TachSensorInput ThiswirewillcontinuallymonitorthetachratewhiletheengineisrunningunderpowersuppliedbytheRemoteStarter. This wire will be routed through the fire wall into the engine compartment. It is necessary to use an existing grommet when passing wires through the fire wall to prevent short circuiting. Connect this wire to the existing tach wire, or the negative side of the ignition coil in the vehicle. (See RF Program Settings). RedandGreen2PinWhiteConnector:DoorLockOutputs The
ملخص المحتوى في الصفحة رقم 6
1. RF Programmable Features: Default Feature Selection 1 Flash 2 Flashes 1 Second First 1 Second Door Locks 3.5 Second Door Locks 10 Minute Second 10 Minute Run Time 15 Minute Run Time Steady Third Park Lights Steady On Park Lights Flash Tach Fourth (No Function) Tach Operation ------------ Fifth (No Function) (No Function) Off During Crank Sixth Ignition 2 Off During Crank Ignition 2 On During Crank Off Seventh Diagnostics Off Diagnostics On ------------- Eighth (No Function) (No Function) Topr
ملخص المحتوى في الصفحة رقم 7
NEUTRALSTARTSAFETYTEST: The intent of the neutral start switch is to prevent the vehicle from starting while the gear selector is in any position other than Park, or Neutral. When installing a Remote Start Device, it is imperative that the Yellow Starter wire be connected to the ignition switch side of the Neutral Start Switch. Consideration for the placement of a starter inhibit relay is important as well, and should be connected to the ignition switch side of the Yellow Start Wire. To test the
ملخص المحتوى في الصفحة رقم 8
KEYINSENSORCIRCUITS: IfthevehicleyouareworkingondoesnothaveoryoucannotlocatetheECMreferencewire,therearetwo alternativesavailable. Althoughnotpreferred,thevehicleKeyInSensormaybereconfiguredtoallowamargin ofsafetyandwillpreventthevehiclewithaMechanicalNeutralStartSwitchfromstartingingear. AUDIOVOXADVISESTHATYOUMAINTAINTHEFACTORYCIRCUITWHENEVERPOSSIBLE. Thefollowing twocircuitsmaybeusedonlyiftheabovecircuitisnotavailable. NOTE: Whencompletinganinstallationusingeitherofthefollowingkeyinsensorcircu
ملخص المحتوى في الصفحة رقم 9
To connect to the key in sensor as shown in method 1: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. Cut this wire and connect the ignition cylinder side to terminal 30 of a P&B VF45F11 or equivalent relay. E. Connect the cathode (striped) side of a 4002 series diode to th
ملخص المحتوى في الصفحة رقم 10
NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, be certain to use a dual diode assembly as shown in the diagram above. AFTER THE CONNE
ملخص المحتوى في الصفحة رقم 11
WIRING THE 12 PIN INPUT / OUTPUT HARNESS 12PINCONNECTOR EXISTINGPARKINGLAMPWIRE WHITE PARKINGLAMP l SPLICE WHITE TO+12VOLTBATTERYFORPOSITIVESWITCHEDPARKINGLIGHTS TOCHASSISGROUNDFORNEGATIVESWITCHEDPARKINGLIGHTS SPLICE EXISTING l BROWNw/BLACK BRAKESWITCH l l BROWN m POSITIVE INHIBIT1 CONTROLSWITCH BLACKw/WHITE CHASSIS GROUND HOOD PINSWITCH GREY IGNITION3 LIGHTBLUE OR SHOCKBY-PASS GREYw/BLACK NEGATIVEINHIBIT2 BLACK TOCHASSIS GROUND DARKGREEN TACH YELLOW w/BLACK TO ALARM'S IGNITION INPUT- (YELLOWWIR
ملخص المحتوى في الصفحة رقم 12
© 1998 Audiovox Corporation, Hauppauge, NY 11788 128-5404
