ملخص المحتوى في الصفحة رقم 1
M Mo od de ell 2 24 49 92 27 7
➤O Ow wn ne er r’’s s//IIn ns stta alllla attiio on n G Gu uiid de e
ملخص المحتوى في الصفحة رقم 2
lliim miitte ed d lliiffe ettiim me e c co on ns su um me er r w wa ar rr ra an ntty y Directed Electronics (hereinafter "Directed") promises to the original purchaser to repair or replace with a comparable reconditioned Directed DIY remote start unit if this Directed DIY remote start unit (hereinafter "Unit"), excluding without limitation, any remote transmitters or associated accessories, proves defective in materials or workman- ship under normal use for the life of the vehicle which the U
ملخص المحتوى في الصفحة رقم 3
OR IN CONNECTION WITH THE INSTALLATION, USE, IMPROPER USE, OR INABILITY TO USE, THE PRODUCT, EVEN IF THE PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR CON- SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA. I IM MP PO
ملخص المحتوى في الصفحة رقم 4
tta ab blle e o off c co on ntte en ntts s lli im mi it te ed d lli if fe et ti im me e c co on ns su um me er r w wa ar rr ra an nt ty y.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. i i I In ns st ta allll G Gu ui id de e .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
ملخص المحتوى في الصفحة رقم 5
© 2006 Directed Electronics 2
ملخص المحتوى في الصفحة رقم 6
Install Guide what is included Control Module 6-Pin Main H1 Harness 8-Pin H2 Secondary Harness Heavy Gauge Wires Antenna and cable Two 5-button remotes Crash code card 3-pin Keyless Entry harness Combination Momentary Switch and LED Hood Pin Switch Hardware Kit DVD—Do-It-Yourself Installation Video Additional parts may be required (such as relays or bypass). installation tools Digital Multi-Meter Drill 1 /4 Drill Bit (for hood pin switch) Screwdrivers (Phillips and Flathead) Wire Stripper Solde
ملخص المحتوى في الصفحة رقم 7
important information Congratulations on the purchase of your remote start keyless entry system. This system will allow convenient access to your vehicle with the push of a button, as well as remote start and other optional features. Properly installed, this system will provide years of trouble-free operation. Please take the time to carefully read this User’s Guide in its entirety and watch the READY REMOTE Do-It-Yourself Installation Video (DVD) prior to installing your system. You can print a
ملخص المحتوى في الصفحة رقم 8
fcc/id notice ➜ This device complies with Part 15 of FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. warning! safety first The following safety warnings must be observed a
ملخص المحتوى في الصفحة رقم 9
TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this user’s guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. After t
ملخص المحتوى في الصفحة رقم 10
Wiring Quick Reference Guide © 2006 Directed Electronics 7 Heavy Gauge Wires BLUE WHITE (+) PINK PINK YELLOW GREEN (+) output to ign/acc2 circuit Fused light flash jumper Black (-) Heavy guage MOMENTARY SWITCH PORT ground wire H1 ANTENNA CABLE PORT YELLOW (+/-) parking light output BROWN/WHITE (-) factory alarm disarm output SENSOR PORT VIOLET (-) negative hood pin shutdown output YELLOW/RED (-) lock or (+) unlock output WHITE/RED (-) unlock or (+) lock output ORANGE (+) brake input WHITE/BLACK
ملخص المحتوى في الصفحة رقم 11
H1 Harness - 6 pin connector ___ YELLOW (+/-) parking light output H H1 1/ /1 1 ___ BROWN/WHITE (-) factory disarm output H H1 1/ /2 2 ___ VIOLET (-) hood pin shutdown input H H1 1/ /3 3 ___ ORANGE (+) brake switch shutdown input H H1 1/ /4 4 ___ H H1 1/ /5 5 WHITE/BLACK (-) 400mA status output ___ H H1 1/ /6 6 RED/WHITE (-) remote start activation input Pin # Color Note H1/1 Selectable positive or negative parking light output Yellow H1/2 Use this wire if the vehicle is equipped with a Brown/Wh
ملخص المحتوى في الصفحة رقم 12
H2 Harness - 8 pin connector ___ GREEN Tachometer input H H2 2/ /1 1 ___ BLUE (-) 400mA horn/siren output H H2 2/ /2 2 ___ RED/BLACK (-) wait-to-start input H H2 2/ /3 3 ___ YELLOW/GREEN (+) ignition output H H2 2/ /4 4 ___ GREEN/WHITE (-) 400mA trunk release output H H2 2/ /5 5 ___ BROWN (-) 400mA RAP, Domelight, Starter Kill H H2 2/ /6 6 ___ YELLOW/BROWN (-) 400mA headlight output H H2 2/ /7 7 ___ H H2 2/ /8 8 GRAY/BLACK (-) door trigger input Pin # Color Note H2/1 Use this wire if the vehic
ملخص المحتوى في الصفحة رقم 13
H3 harness - 3 pin connector ___ YELLOW/RED (-) lock/(+) unlock H H3 3/ /1 1 ___ EMPTY H H3 3/ /2 2 ___ WHITE/RED (-) unlock/(+) lock H H3 3/ /3 3 relay heavy gauge wires ___ GREEN (+) Ign2 or Acc2 output 1 1 ___ PINK (+) 12 volt input 2 2 ___ BLUE (+) ignition 1 output 3 3 ___ WHITE (+) accessory output 4 4 ___ PINK (+) 12 volt input 5 5 ___ 6 6 YELLOW (+) starter output BLACK (-) ground © 2006 Directed Electronics 10
ملخص المحتوى في الصفحة رقم 14
Installation Overview Be sure to read this section thoroughly and view the Do-It- Yourself Installation DVD video in its entirety before starting the installation. Pay special attention to all warnings to prevent per- sonal injury or damage to your vehicle. Visit our 24-hour technical web site (www.readyremote.com) to get a vehicle-specific wiring guide prior to starting this installa- tion. Have your crash code number handy when contacting tech support or visiting the web site. During the insta
ملخص المحتوى في الصفحة رقم 15
Step 1, Heavy Gauge Wire Connections Ground Wire The BLACK wire connects to the pin next to the light flash jumper fuse. First strip back a ¾-inch section of the insulation off the BLACK wire and crimp a ring terminal (not provided) to that wire. Locate a clean, paint-free metal surface in the drivers kick panel (do not ground on dash). Using a self-tapping screw, drill the screw with the ring terminal to the kick panel. Once screwed down, pull on the wire to ensure a good connection.
ملخص المحتوى في الصفحة رقم 16
Once the lower dash panel has been removed, locate the ignition harness at the back of the key cylinder. This is usually a group of heavy gauge wires (approximate 14ga.). Place the black lead of the LED tester to a clean metal surface in the kick panel area and secure it. Probe one of the thicker gauge wires. The ignition wire colors of your specific vehicle can be obtained at www.readyremote.com. note! More problems are attributed to poor ground connections than any other cause. Take extra ca
ملخص المحتوى في الصفحة رقم 17
With the key in the off position, test the suspect wire. The constant power wire will read 12V on the multimeter. Once the constant power wire has been identified, solder the two heavy gauge 12 VOLT wires (PINK) from the control module to it and wrap the connection with electrical tape. note! If the vehicle has more than one constant power wire, utilize two of them. Connect one of the heavy gauge PINK wires to one of the constant power wires and the other heavy gauge PINK wire to the other cons
ملخص المحتوى في الصفحة رقم 18
If your vehicle requires more than two ignitions, an additional relay (not provided) is required. Refer to the diagram below. +12 VDC CONSTANT (FUSED 20A) nd 2 IGNITION RELAY (NOT PROVIDED) nd 87 TO 2 IGNITION GROUND 86 87A 85 30 nd TO 2 IGNITION +12 VDC CONSTANT (FUSED 20A) rd 3 IGNITION RELAY (NOT PROVIDED) GREEN (+) OUTPUT nd 87 TO 2 IGNITION GROUND 85 86 87A 30 rd TO 3 IGNITION © 2006 Directed Electronics 15
ملخص المحتوى في الصفحة رقم 19
Accessory and Starter wires The starter and accessory wires will be located in the same harness as the ignition and constant power. To find the accessory wire leave the multimeter’s black lead connected to ground. Take the red lead and probe the wire suspected to be the accessory wire. With the key off, your multi- meter should read 0 volts. Turn the key to the on position the multimeter should read 12 volts. Now turn the key to the crank position. If you have the correct accessory wire the mul
ملخص المحتوى في الصفحة رقم 20
If the GREEN wire is being used for ign2 an additional relay (not provided) is required for a 2nd accessory. Refer to the diagram below. +12 VDC CONSTANT (FUSED 20A) ACCESSORY RELAY (NOT PROVIDED) 87 TO ACCESSORY GROUND 86 85 87A 30 TO ACCESSORY +12 VDC CONSTANT (FUSED 20A) nd 2 ACCESSORY RELAY (NOT PROVIDED) WHITE (+) 30A OUTPUT TO 87 ACCESSORY CIRCUIT GROUND 86 85 87A 30 nd TO 2 ACCESSORY Now that the accessories have been located, find the suspected starter wire according to the web informat
