ملخص المحتوى في الصفحة رقم 1
Model PRO 9644
Owner’s Manual
3 Button Remote Security System with Starter Disable
IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this
system is equipped with selectable manual override circuitry. It is possible that you will need to
manually override your security system if the transmitter becomes lost, or inoperative due to
battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is
necessary to fully understand the procedure requir
ملخص المحتوى في الصفحة رقم 2
YOUR " ANTI CODE GRABBING " TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and re-transmit at a later time to disarm your system. Your anti code grabbing transmitters will change their signal every tim
ملخص المحتوى في الصفحة رقم 3
If the horn beeps three times, then you have left a door, trunk, or hood lid ajar. Simply close the opened entry point to provide full protection. Doors Lock - Optional Headlight Illumination - Optional The vehicle’s headlights turn on for approximately 30 seconds, illuminating the path as you leave the vehicle. ARMING THE SYSTEM - PASSIVE ( AUTOMATIC ) 1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid, and trunk lid. Red dash mounted LED begins to flash rapi
ملخص المحتوى في الصفحة رقم 4
Optional - Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. DISARMING THE SYSTEM 1. As you approach the vehicle, press and release the Unlock button on the keychain trans- mitter. Red dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is re arming automatically. Open any door to suspend the automatic arming. Parking Lights flash t
ملخص المحتوى في الصفحة رقم 5
flashing rapidly, indicating that the system is re-arming automatically. Open any door to suspend the automatic arming. Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. Siren will not sound. If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNIN
ملخص المحتوى في الصفحة رقم 6
to a light activated entry point if the alarm was installed using the voltage sensing feature. If the LED is flashing three times...pause...three times...pause...etc., then an intrusion attempt was made through one of the vehicle’s doors. These intrusion warning indicators are stored in the system’s memory, and will only be erased when the ignition key is turned on. VALET SWITCH The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter
ملخص المحتوى في الصفحة رقم 7
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the pushbutton switch from 1 up to 9 times. 5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on. 6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing the pushbutton switch from 1 up to 9 times. 7. Finish by turning the ignition switch to the off position. If the new code was accepted, the unit will report back the newly entered code, by f
ملخص المحتوى في الصفحة رقم 8
MANUALLY OVERRIDING YOUR SYSTEM: USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed, and the default override code of 11 is in the system's memory. 1. Enter the vehicle and turn the ignition switch to the on position. NOTE: The siren will sound. 2. Within 5 seconds, press and release the pushbutton switch 1 time. 3. Within 5 seconds, turn the ignition switch off then on. 4. Within 5 seconds, press and release the pushbutton switch 1 time. 5. Turn the igniti
ملخص المحتوى في الصفحة رقم 9
OPTIONAL DEVICE OUTPUT (CHANNEL 3) Controlled By: Option Button, Both Lock & Unlock Button, Both Option & Lock Button, or Both Option and Unlock Button. This security system is equipped with an output which will activate when the appropriate transmitter button is depressed for four seconds. Optional devices that may be connected to this channel are: Remote Electric Trunk Release Remote Car Starter Remote Window Closure Remote Garage Door Interface NOTE: In addition there may be a
ملخص المحتوى في الصفحة رقم 10
PRO 9644 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN AND / OR HORN CHIRP INDICATORS 1 CHIRP * = ARM 2 CHIRPS * = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH = ARM 2 FLASHES = DISARM 3