ملخص المحتوى في الصفحة رقم 1
INSTALLATION INSTRUCTIONS FOR PART 99-9105
APPLICATIONS
Audi A4 2000-2001
(Symphony Radio Only)
99-9105
KIT FEATURES
• DIN radio provision with pocket
• ISO radio provision with pocket
• Double DIN radio provision
KIT COMPONENTS
A) Radio Housing • B) Pocket • C) Trim Plate • D) ISO Brackets • E) Double DIN Trim Plate
• F) Double DIN Brackets
C
D
A
B
F
E
TOOLS REQUIRED:
* 86-9001 Head Unit Removal Tool • Flat Blade Screwdriver Or Panel Removal Tool
Note: Two sets of the he
ملخص المحتوى في الصفحة رقم 2
99-9105 TABLE OF CONTENTS Dash Disassembly - Audi A4 2000-2001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 3 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..5
ملخص المحتوى في الصفحة رقم 3
DASH DISASSEMBLY 99-9105 AUDI A4 2000-2001 1 Disconnect the negative battery A terminal to prevent an accidental short circuit. 2 Insert Metra’s 86-9001 into the slots in the factory radio and pull the radio from the dash. (Figure A) CD LOAD AS 3 Disconnect the wiring. FM MENU AM TONE SAT RDS Continue to kit assembly. TAPE SCAN 1
ملخص المحتوى في الصفحة رقم 4
KIT ASSEMBLY 99-9105 DIN RADIO PROVISION WITH POCKET A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) Slide the aftermarket radio into the 2 cage and secure. (Figure B) 3 Snap the pocket into the Radio Housing until secure. (Figure C) Continue to final assembly. B C 2
ملخص المحتوى في الصفحة رقم 5
KIT ASSEMBLY 99-9105 ISO RADIO PROVISION WITH POCKET 1 Mount the ISO Brackets to the A radio with the screws supplied with the unit. (Figure A) 2 Slide the radio into the radio opening until the side clips engage. (Figure B) 3 Snap the ISO Trim Plate into the Radio Housing. (Figure C) 4 Snap the pocket into the radio B housing. (Figure C) Continue to final assembly. C 3
ملخص المحتوى في الصفحة رقم 6
KIT ASSEMBLY 99-9105 DOUBLE DIN RADIO PROVISION A 1 Cut and remove center divider from radio housing. (Figure A) Snap the Double DIN brackets to the 2 inside edge of the radio housing. (Figure B) 3 Slide the Double DIN radio into the Double DIN bracket/radio housing assembly and secure the unit to the kit using the screws supplied with the radio. (Figure C) B 4 Snap the Double DIN trim-plate onto the housing/radio assembly. (Figure D) Continue to final assembly. D C 4
ملخص المحتوى في الصفحة رقم 7
FINAL ASSEMBLY 99-9105 FINAL ASSEMBLY A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Snap radio housing assembly into factory radio opening. 3 FINAL WI
ملخص المحتوى في الصفحة رقم 8
99-9105 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/17/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-9105
