ملخص المحتوى في الصفحة رقم 1
R
LCD Projector Commercial Use
Operating Instructions
Model No. PT-LB30NTU
PT-LB30U
POWER
INPUT
VIDEO RGB
AUTO
MENU
SETUP
ENTER
FREEZE SHUTTER
STD
VOLUME D.ZOOM
INDEX
WINDOW
PROJECTOR
Before operating this product, please read the instructions carefully and save this
manual for future use.
TQBJ 0170
ENGLISH
ملخص المحتوى في الصفحة رقم 2
Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-LB30NTU / PT-LB30U Serial number: IMPORTANT SAFETY NOTICE WARNING:
ملخص المحتوى في الصفحة رقم 3
CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the Do not remove purpose of the grounding plug. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The
ملخص المحتوى في الصفحة رقم 4
WARNING: BNot for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. BFor permanently connected equipment, a readily accessible disconnect device shall be incorporated in the building installation wiring; BFor pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. Declaration of Conformity Model Number: PT-LB30NTU/PT-LB30U Trade Name: Panasonic Responsible party
ملخص المحتوى في الصفحة رقم 5
Contents TV-SYSTEM, STILL MODE, Preparation SIGNAL MODE, Projecting sRGB- IMPORTANT SAFETY NOTICE ...2 compatible pictures Precautions with regard to Adjusting the position...............41 safety .........................................6 POSITION, DOT CLOCK, CLOCK PHASE, ASPECT, RESIZING, Accessories ...............................10 FRAME LOCK Before use ..................................11 Changing the display language...44 Location and function of each Option settings .....................
ملخص المحتوى في الصفحة رقم 6
Precautions with regard to safety WARNING If you notice smoke, strange smells or noise coming from the projector, disconnect the power cord plug from the wall outlet. BDo not continue to use the projector in such cases, otherwise fire or electric shocks could result. BCheck that no more smoke is coming out, and then contact an Authorized Service Center for repairs. BDo not attempt to repair the projector yourself, as this can be dangerous. Do not install this projector in a place which is not st
ملخص المحتوى في الصفحة رقم 7
Do not do anything that might damage the power cord or the power cord plug. BDo not damage the power cord, make any modifications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle. BIf the power cord is used while damaged, electric shocks, short-circuits or fire may result. BAsk an Authorized Service Center to carry out any repairs to the power cord that might be necessary. Do not handle the power cord plug wit
ملخص المحتوى في الصفحة رقم 8
During a thunderstorm, do not touch the projector or the cable. BElectric shocks can result. Do not use the projector in a bath or shower. BFire or electric shocks can result. Do not look into the lens while the projector is being used. BStrong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes. BBe especially careful not to let young children look into the lens. In addition, disconnect the power cord plug when you are away from the
ملخص المحتوى في الصفحة رقم 9
Always disconnect all cables before moving the projector. BMoving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur. Do not place any heavy objects on top of the projector. BFailure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury. Do not short-circuit, heat or disassemble the batteries or place them into water or fire. BFailure to observe this may cause the batteries to
ملخص المحتوى في الصفحة رقم 10
NOTICE: BThis product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: Accessories Check that all of the accessories shown below have been included with your projector. Card remote con
ملخص المحتوى في الصفحة رقم 11
Before use Caution when moving the projector Be sure to attach the lens cover before moving the projector. The projection lens is extremely susceptible to vibration and shocks. When moving the projector, use the accessory carrying bag. When placing the projector inside the carrying bag, position it so that the lens is facing upward. Do not put anything else in the bag other than the projector and the cables. Cautions regarding setting-up Avoid setting up in places which are subject to vibration
ملخص المحتوى في الصفحة رقم 12
Location and function of each part Projector #$% & ' * ) ' ( #Projector control panel (page 16) $Zoom ring (page 25) %Focus ring (page 25) &Security lock This can be used to connect a commercially-available theft-prevention cable (manufactured by Kensington). This security lock is compatible with the Microsaver Security System from Kensington. 'Leg adjuster buttons (L/R) (page 25) These buttons are used to unlock the front adjustable legs. Press to adjust the angle of til
ملخص المحتوى في الصفحة رقم 13
Projector $% # ( ' & #Connector panel (page 14) $Air outlet port Do not cover this port. %Speaker &Front adjustable legs (L/R) (page 25) 'Air inlet port, Air filter (page 54) Do not cover this port. (Lamp unit cover (page 55) NOTE: BDuring projection of an image, the cooling fan will operate, emitting a small noise as it operates. This noise may change depending on the ambient temperature. Turning the lamp on or off will cause this noise to increase a little. BBy using the “OPT
ملخص المحتوى في الصفحة رقم 14
Connector panel #$% & ' ( , + * ) #SERIAL connector (pages 20, 21, 22 and 64) This connector is used to connect a personal computer to the projector in order to control the projector externally. (RS-232C compatible) $RGB1 IN connector (pages 20 and 21) This connector is used to input RGB signals and YPBPR signals. %RGB2 IN/1 OUT connector (pages 20, 21 and 46) This connector is used to input or output RGB signals and YPBPR signals. Adjust “RGB2 SELECT” in the “OPTION” menu to select whether you
ملخص المحتوى في الصفحة رقم 15
*AUDIO OUT connector (pages 20, 21, and 22) This connector is used to output the audio signals which are input to the projector. If audio equipment is connected to this connector, no sound will be output from the built-in speakers. +RGB AUDIO 1IN/2IN connectors (pages 20 and 21) These connectors are used to input audio signals, and they correspond to the RGB1 IN/2 IN connectors respectively. ,Power input socket (AC IN) (page 24) The accessory power cord is connected here. Do not use any power co
ملخص المحتوى في الصفحة رقم 16
Projector control panel Menu operation #$% & ' ( * ) +, Remote control unit ' POWER INPUT ( ) VIDEO RGB * + AUTO MENU SETUP , - ENTER . / FREEZE SHUTTER 0 STD VOLUME D.ZOOM INDEX WINDOW 1 2 PROJECTOR #RGB INPUT indicator This indicator illuminates when a signal is being input to the connector (RGB1 IN or RGB2 IN) selected using the input select buttons. $LAMP indicator (page 53) This indicator illuminates when it is time to replace the lamp unit. It flashes if a cir
ملخص المحتوى في الصفحة رقم 17
the projector or around it. If the temperature rises above a certain level, the power supply will be turned off automatically and the indicator will flash. &Illumination sensor (page 39) This sensor detects the luminance when the “DAYLIGHTVIEW” function is operating. Do not cover the projector and do not place any object on the projector when using it. 'POWER button (pages 24, 26 and 27) This button is used to turn the power on and off. This button on the projector illuminates red when the proje
ملخص المحتوى في الصفحة رقم 18
ملخص المحتوى في الصفحة رقم 19
ملخص المحتوى في الصفحة رقم 20
Connections Notes on connections B Read the instruction manual for each peripheral device carefully before connecting it. B Turn off the power supply for all peripheral devices before making any connections. B If the cables necessary for connection are not included with the peripheral device or available as an option, you may need to prepare a proper cable for the device concerned. B If there is a lot of jitter in the video signal, the projected image may flicker. In such cases, it will be neces
