ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2013 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclai
ملخص المحتوى في الصفحة رقم 3
IN8606HD User’s Manual Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information. N
ملخص المحتوى في الصفحة رقم 4
Preface Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees. In addition, the projector should not be installed in any other way except desktop and ceiling mount positions. Otherwise lamp life could decrease dramatically, and may lead to other unpredictable damage. Allow at least 50 cm (16.69 inch) clearance around the exhaust vent. (19.69 inch) (19.69 inch) (19.69 inch) (3.94 inch)
ملخص المحتوى في الصفحة رقم 5
IN8606HD User’s Manual Power Safety Only use the supplied power cord. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. Remove the batteries from the remote control when storing or not in use for a prolonged period. Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 36 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug
ملخص المحتوى في الصفحة رقم 6
Preface Table of Contents GETTING STARTED...........................................................................................................................................................1 PACKING CHECKLIST........................................................................................................................................................... 1 VIEWS OF PROJECTOR PARTS..............................................................................................
ملخص المحتوى في الصفحة رقم 7
IN8606HD User’s Manual SPECIFICATIONS.............................................................................................................................................................46 SPECIFICATIONS................................................................................................................................................................. 46 PROJECTION DISTANCE VS. PROJECTION SIZE..................................................................................
ملخص المحتوى في الصفحة رقم 8
IN8606HD User’s Manual GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: DLP PROJECTOR WITH LENS CAP REMOTE CONTROL HDMI CABLE POWER CORD (BATTERIES NOT INCLUDED) CD-ROM QUICK START GUIDE WARRANTY CARD (THIS USER’S MANUAL) Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is recommended that you keep the original packing material in case you
ملخص المحتوى في الصفحة رقم 9
IN8606HD User’s Manual Views of Projector Parts Front-right View 12 34 5 ITEM LABEL DESCRIPTION SEE PAGE IR receiver Receive IR signal from remote control 1. Lens Projection Lens 2. Focus ring Focuses the projected image 3. 16 Zoom ring Enlarges the projected image 4. See Top view—On-screen Display (OSD) buttons Function keys 5. 3 and LEDs. Important: Do not block ventilation openings. Locate the projector in a well-ventilated area without obstructions to intake or exha
ملخص المحتوى في الصفحة رقم 10
IN8606HD User’s Manual Top view—On-screen Display (OSD) buttons and LEDs 1 2 3 ITEM LABEL DESCRIPTION SEE PAGE Turns the projector On and Off 1. Red Lamp Failure LAMP LED 2. Blinking Red Error code Projector is in standby or is fully Blue 42 powered on (lamp is lit). POWER LED 3. Projector is initializing or cooling down. It Blinking Blue can also indicate an error code when blinking in conjunction with the Lamp LED. – 3 –
ملخص المحتوى في الصفحة رقم 11
IN8606HD User’s Manual Rear view 12 3 45 6 7 8 9 10 16 15 13 11 14 12 ITEM LABEL DESCRIPTION SEE PAGE AC IN Connect a POWER cable 1. 11 Connect the 3D IR glasses transmitter 3D SYNC 2. (Note: For Specific 3D IR glasses only) HDMI 1 Connect an HDMI cable from a HDMI device 3. HDMI 2 Connect an HDMI cable from a HDMI device 4. Service use only. 5. (USB) VGA IN Connect a RGB cable from a computer 6. RS-232C Connect a RS-232 serial port cable for remote control 7. COM
ملخص المحتوى في الصفحة رقم 12
IN8606HD User’s Manual DC12V Trigger Note: To use this feature, you must plug in the connector before turn on/off the projector. Screen controllers are supplied and supported by screen manufacturers. Do not use this jack for anything other than intended use. Connectivity Note: If your video equipment has multiple connection options, please note that HDMI provides the highest quality image, followed by Component and then S-video. Composite provides the least quality image. Warn
ملخص المحتوى في الصفحة رقم 13
IN8606HD User’s Manual Bottom view 40.8mm(1.61inch) 173.9mm (6.85inch) 4.5mm (0.18inch) 146.0mm (5.75inch) 68.7mm (2.70inch) ITEM LABEL DESCRIPTION SEE PAGE Contact your dealer for information on mounting the projector on a 1. Ceiling support holes ceiling Tilt adjustor Rotate adjuster lever to adjust angle position. 2. 15 Note: If you are installing the projector on the ceiling, we strongly recommend using InFocus approved ceiling mounts for proper fitting, ventilation and i
ملخص المحتوى في الصفحة رقم 14
IN8606HD User’s Manual Remote Control Parts 12 3 15 4 14 13 5 12 11 6 7 10 9 8 Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3.
ملخص المحتوى في الصفحة رقم 15
IN8606HD User’s Manual ITEM LABEL DESCRIPTION SEE PAGE: Up Navigates up and changes settings in the OSD 1. 17 2. Enter Changes settings in the OSD Power Turns the projector on or off 3. 11 Right Navigates to the right and changes settings in the OSD 4. Volume + Increases volume 5. 16 Volume - Decreases volume 6. Mute Mutes the built-in speaker 7. 8. Freeze Freeze/unfreezes the on-screen picture Source Selects the input device 9. Auto Auto adjustment for frequenc
ملخص المحتوى في الصفحة رقم 16
IN8606HD User’s Manual Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.
ملخص المحتوى في الصفحة رقم 17
IN8606HD User’s Manual SETUP AND OPERATION Inserting the Remote Control Batteries Remove the battery compartment 1. cover by sliding the cover in the direction of the arrow (A). Pull out the cover (B). Insert the battery with the positive 2. side facing up. Replace the cover. 3. Caution: 1. Only use a 3V lithium battery (CR2025). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the batteries when not using the projector for prolong
ملخص المحتوى في الصفحة رقم 18
IN8606HD User’s Manual Turning the projector on and off Connect the power cord to the 1. projector. Connect the other end to a wall outlet. The POWER LED on the projector light. Turn on the connected devices. 2. Ensure the POWER LED is not 3. flashing. Then press the POWER button to turn on the projector. The projector splash screen displays and connected devices are detected. See Setting an Access Password (Security Lock) on page 13 if the security lock is enabl
ملخص المحتوى في الصفحة رقم 19
IN8606HD User’s Manual To turn the projector off, press the 5. POWER button. When the “Power Off? Press Power again” message appears, press the POWER button. The projector turns off. Caution: 1. Be sure to remove the lens cap before starting projector. 2. Do not unplug the power cord until the POWER LED stops flashing–indicating the projector has cooled down. –12 –
ملخص المحتوى في الصفحة رقم 20
IN8606HD User’s Manual Setting an Access Password (Security Lock) You can use the four arrow buttons on the remote to set a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the projector. (See Navigating the OSD on page 17 and Setting the OSD Language on page 18 for help on using OSD menus.) Important: Keep the password in a safe place. Without the password, you will not be able to use the projector. If you lose the pas
