ملخص المحتوى في الصفحة رقم 1
TOSHIBA REMOTE RECEIPT PRINTER
TRST-A10 SERIES
Owner's Manual
ملخص المحتوى في الصفحة رقم 2
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Warnung Dies ist ein Klasse A Produkt. In einer örtlichen Umgebung kann dieses Gerät Funkstörungen verursachen. ATTENTION Ce produit est de classe A. Dans un environnement domestique, il
ملخص المحتوى في الصفحة رقم 3
Safety Summary EO1-13019 Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual,
ملخص المحتوى في الصفحة رقم 4
Safety Summary EO1-13019 If foreign objects (metal When unplugging the power cords, Disconnect Disconnect fragments, water, liquids) enter be sure to hold and pull on the plug the plug. the plug. the machines, first turn off the portion. Pulling on the cord portion power switches and disconnect may cut or expose the internal wires the power cord plugs from the and cause fire or electric shock. outlet, and then contact your authorised TOSHIBA TEC representative for assistance.
ملخص المحتوى في الصفحة رقم 5
EO1-13019 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW ------------------------------------------------------------ 1-1 1.1 Introduction ----------------------------------------------------------------------------- 1-1 1.2 Features --------------------------------------------------------------------------------- 1-1 1.3 Accessory-------------------------------------------------------------------------------- 1-1 2. SPECIFICATIONS -------------------------------------------------
ملخص المحتوى في الصفحة رقم 6
EO1-13019 1. PRODUCT OVERVIEW 1.1 Introduction 1. PRODUCT OVERVIEW 1.1 Introduction Thank you for purchasing the TOSHIBA TRST-A10 Series Thermal Printer. This printer is a compact line thermal printer designed to be connected to a TOSHIBA POS terminal or used as a kitchen printer, etc. It prints both 80 mm-wide and 58 mm-wide receipts at the maximum print speed of 225mm
ملخص المحتوى في الصفحة رقم 7
EO1-13019 2. SPECIFICATIONS 2.1 Printer 2. SPECIFICATIONS 2.1 Printer Item Description Printing method Line thermal dot printing method Printing width 80 mm (576 dots) 58 mm (432 dots) Resolution 203.2 dpi x 203.2dpi Printing speed Max. 9 ips max (225 mm/sec) for 75W, 55W mode 2 color printing Max 50 mm/sec Printing columns 80 mm Paper 48 Column (at 16.9 cpi Standard Character) 64 Column (at 22.6 cpi Compress Character) 58 mm Paper 36 Column (at 16.9 cpi S
ملخص المحتوى في الصفحة رقم 8
EO1-13019 2. SPECIFICATIONS 2.2 Options 2.2 Options Option Model Description AC Adapter This AC adapter is for the exclusive use of the TRST-A10/A15 TOSHIBA KIT-A10-ACA-QM-R remote receipt printer. KIT-A10-ACB-QM-R KIT-A10-ACB type is conformed to Level 4 of the California Energy Commission (CEC). Parallel Interface Board This parallel interface board is for the KIT-A10-PIF-QM-R exclusive use of the TRST-A10/A15 TOSHIBA remote receipt printer. Partition This partition
ملخص المحتوى في الصفحة رقم 9
EO1-13019 2. SPECIFICATIONS 2.3 Receipt Roll 2.3 Receipt Roll W1 or W2 Paper type Thermal paper rolled with the print side facing outside Width (W1) 80 +/ -1.0 mm Width (W2) 58 +0/ -1.0 mm (With optional 58 mm paper guide) Outer diameter (D) 76 +/-2.0 mm Paper thickness (T) 0.065 +/- 0.005 mm 2 Weight 53 g/m Outer core diameter 21.5 mm Inner core diameter 12.5 +/- 0.5 mm Recommended thermal Only paper rolled onto a core is acceptable, how
ملخص المحتوى في الصفحة رقم 10
EO1-13019 3. APPEARANCE 3.1 Front/Rear View 3. APPEARANCE 3.1 Front/Rear View Front View Rear View Printer Cover LED Top Cover Feed Button Power Switch 3.2 LED and Feed Button POWER LED (Blue) Lights when the power is turned on. ERROR LED (Blinking Blue) The Error LED indicates an error by blinking FEED Button Used to feed receipt paper. A touch of this button causes one line feed. Pressing and holding it feeds the paper continuously. When the po
ملخص المحتوى في الصفحة رقم 11
EO1-13019 3. APPEARANCE 3. 2 LED and Feed Button Error Status Table Blue LED Blinking (Slow) Problem What to Do Where to Go Receipt paper is low See “Loading the There are about 4 ½ meters, ± 3 meters, Receipt Roll” in (15 feet, ± 10 feet) of paper left. Change chapter 5.3. the paper soon to avoid running out of paper part way through a transaction. Blue LED Blinking (Fast) Problem What to Do Where to Go Receipt paper is out Change the paper now. Do not run a See “Loa
ملخص المحتوى في الصفحة رقم 12
EO1-13019 3. APPEARANCE 3. 3 Connectors 3.3 Connectors CAUTION! 1.The drawer interface connector is exclusively for connecting the drawer. Do not connect a phone line or any other cables than the drawer cable to this connector. Doing so may cause a failure of the phone line and this printer. 2.To the DC24V connector (socket connector), do not connect anything other than the built-in AC adapter. 3.The built-in AC adapter is exclusively for this printer. Do not use it for any other
ملخص المحتوى في الصفحة رقم 13
EO1-13019 4. SET UP PROCEDURE 4.1 Requirements for Operation 4. SET UP PROCEDURE 4.1 Requirements for Operation This printer has the following requirements: Serial Interface Type The TOSHIBA POS terminal or Personal Computer to be connected must have a serial port. To communicate with the TOSHIBA POS terminal or Personal Computer, an RS-232C interface cable is required. RS-232C cable....... 9 pins USB Interface Type The TOSHIBA POS terminal or Perso
ملخص المحتوى في الصفحة رقم 14
EO1-13019 4. SET UP PROCEDURE 4.1 Requirements for Operation RS-232C cable pin configuration TRST – A10 9 Pin Female 9 Pin Female 4-2
ملخص المحتوى في الصفحة رقم 15
EO1-13019 4. SET UP PROCEDURE 4.1 Requirements for Operation USB cable connector 2 1 34 Printer View End Parallel Interface Type (Option) IEEE 1284-B receptacle PIN No. Signal 1 /STROBE 2-9 PD1-8 10 /ACK 11 BUSY 12 PERROR 13 SELECT 14 /AUTOFD 31 /INIT 32 /FAULT 36 /SELECTIN 19-30 GND 15-18 N.C. 33-35 N.C. 4-3
ملخص المحتوى في الصفحة رقم 16
EO1-13019 4. SET UP PROCEDURE 4.2 Setting up the Printer 4.2 Setting up the Printer CAUTION! 1. Place the printer on a flat, stable surface. 2. Do not place the printer close to a heater or where it may be exposed to direct sunlight. 3. Avoid locations where the printer may be exposed to high temperature, high humidity or dust. 4.Care must be taken that no condensation occurs in the printer. If it should, however, do not turn ON the power until the condensation is dried. 5. Use
ملخص المحتوى في الصفحة رقم 17
EO1-13019 5. INSTALLATION PROCEDURE 5.1 Connecting the Power Cord and Interface Cable 5. INSTALLATION PROCEDURE WARNING! 1. Since the power cord and the interface cable are not provided with this unit, please locally purchase ones which meet the specifications. For detail specifications, please contact your nearest authorized TOSHIBA TEC representative. 2. Before connecting the power cord and cables to the printer, turn the power of the POS terminal and printer OFF. 3. Do not pull
ملخص المحتوى في الصفحة رقم 18
EO1-13019 5. INSTALLATION PROCEDURE 5.1 Connecting the Power Cord and Interface Cable 5.1 Connecting the Power Cord and Interface Cable CAUTION! 1. Be sure to hold the connector when plugging in or unplugging the AC adapter cable. 2. Insert the AC adapter cable and the power cord firmly. 1) Turn the printer power OFF. 2) Insert the power cord into the AC inlet. 3) Connect and secure the interface cable to the interface connector in the correct orientation. Serial
ملخص المحتوى في الصفحة رقم 19
EO1-13019 5. INSTALLATION PROCEDURE 5.1 Connecting the Power Cord and Interface Cable 4) Connect the interface cable to the TOSHIBA POS terminal or Personal Computer, and then plug in the power cord to the AC outlet. Interface cable 5-3
ملخص المحتوى في الصفحة رقم 20
EO1-13019 5. INSTALLATION PROCEDURE 5.2 Connecting the Drawer 5.2 Connecting the Drawer 1) Turn the printer power OFF. 2) Connect the drawer cable to the drawer interface connector in the correct orientation. [Drawer interface connector] (6-pin modular connector) A Drawer cable which connects the printer to a drawer is connected to this connector. To this connector, a TOSHIBA drawer can be connected. Do not connect anything other than the
