ملخص المحتوى في الصفحة رقم 1
okilogo.jpg
global logo.jpg
OKIPOS 425D
o425_72.jpg
Developer’s Guide
59336301
ملخص المحتوى في الصفحة رقم 2
Document Title and Part Number OKIPOS 425D Developer’s Guide P/N 59336301 Disclaimer Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki Data assumes no responsibility for the results of errors or omissions beyond its control. Oki Data also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this document will not affect the applicability of the information in it. Mention of so
ملخص المحتوى في الصفحة رقم 3
Contents 1. Setting Up the Printer....................................................................................................................................... 6 1.1. Select a Location ...................................................................................................................................................................6 1.2 Where to install your printer ........................................................................................................
ملخص المحتوى في الصفحة رقم 4
4. Troubleshooting and Repair.......................................................................................................................... 58 4.1 Alarm Indication for a Failure .............................................................................................................................................58 4.1.1 Details of Alarm Indications ................................................................................................................................
ملخص المحتوى في الصفحة رقم 5
6. Command Description.................................................................................................................................... 95 6.1 Control Code List ................................................................................................................................................................95 6.1.1 OEM — Standard Model ...............................................................................................................................
ملخص المحتوى في الصفحة رقم 6
1. Setting Up the Printer 1.1. Select a Location · Firm, level surface capable of supporting approximately 7kg (15.4 lbs). · Clearance to open cover · At least 100mm (4 inches) additional clearance on both sides for adequate ventilation · Nearby power source · Room temperature: 5° to 40° C (41° to 104° F) · Relative humidity: 20 to 80% · Away from direct sunlight · Do not place the printer near a heater. · Do not place it in a location with abrupt temperature changes. · Do not let condensation
ملخص المحتوى في الصفحة رقم 7
1.3 Unpacking Getting Started Check the contents: 1 Printer 2 Ribbon Cartridge If anything is missing or damaged, contact your dealer immediately. o425_72.jpg and o425_07.jpg 1 2 Developer’s Guide: English 7 |
ملخص المحتوى في الصفحة رقم 8
1.4 Installing the Printer Getting to Know the OKIPOS 425D 2 o425_72.jpg 1 4 5 3 1 Printer Cover 2 Control Panel 3 Paper Guide 4 Cover Open Bar 5 ON/OFF Switch OKIPOS 425D 8 |
ملخص المحتوى في الصفحة رقم 9
1.4.1 Remove the Shipping Restraints Important! Save the shipping restraints and packing materials in case you ever need to ship the printer. 1. Remove the five pieces of shipping tape. o425_30.jpg 2. Press the Cover open bar and open the printer cover. o425_31.jpg and o425_32.jpg 3. Remove the two printhead shipping restraints and red rubber, and detach the two pieces of tape. o425_33.jpg 2 1 3 4 1 Printer Cover 2 Shipping Restraint 3 Control Panel 4 Red Rubber Developer’s Guide: English 9 |
ملخص المحتوى في الصفحة رقم 10
1.4.2 Setting the Interface Board Assembly 1.4.2.1 Setting the DIP Switches (RS-232C) A25001.doc Switch Setting DIP SW Function ON OFF 1 Selects the data bit length 7 bits 8 bits 2 Selects between the presence and Present Absent absence of parity bits. 3 Selects the parity Even Parity Odd parity 4 Selects the protocol XON / XOFF Ready / Busy D 5 6 7 Signaling Speed (BPS) I OFF OFF OFF 1200 P Selects the signaling spee
ملخص المحتوى في الصفحة رقم 11
1.4.2.2 Installing the Interface Board Assembly (1) Insert the Interface Board Assembly in the direction of the arrow. o425_84.jpg (2) Secure the Interface Board Assembly with 2 screws. o425_28.jpg Developer’s Guide: English 11 |
ملخص المحتوى في الصفحة رقم 12
1.4.3 Connecting the Computer This printer supports either Parallel Interface or RS232C when the interface board is installed in the printer. To install the interface board, refer to Section 1.4.2.2. 1. Check to be sure that the printer’s power is OFF. 2. Connect the interface cable to the connector shown below. A) Parallel Interface B) Serial Interface o425_24.jpg and o425_82.jpg B A 3. Secure the connector by its latches or screws. 1.4.4 Connecting the Cash Drawer 1. Check to be sure tha
ملخص المحتوى في الصفحة رقم 13
1.4.7 Installing the Ribbon Cartridge 1. Make sure the printer is turned OFF. 2. Press the Cover open bar and open the printer cover. o425_31.jpg and o425_32.jpg 3. Center the printhead. o425_86.jpg Developer’s Guide: English 13 |
ملخص المحتوى في الصفحة رقم 14
4. Unpack the ribbon cartridge. Important! Do NOT remove the ribbon shield from the ribbon! 2 1 o425_07.jpg 3 1 Ribbon Shield 2 Take-up Knob 3 Grip Points 5. Install the new ribbon cartridge. 1) Hold the ribbon cartridge as shown below. o425_87.jpg 2) Fit the grooves in the flat end of the cartridge over the posts on the ribbon plate. OKIPOS 425D 14 |
ملخص المحتوى في الصفحة رقم 15
3) Lower the front of the cartridge over the printhead until it snaps into place. o425_87.jpg and o425_88.jpg 4) Turn the knob (1) in the direction of the arrow on the cartridge to take up the ribbon slack. o425_86.jpg 1 Developer’s Guide: English 15 |
ملخص المحتوى في الصفحة رقم 16
1.5 Installing the Paper Paper Specifications Maximum thickness: 0.3 mm (0.012 inches) A25002.doc Media Type Width Length Weight Number Thickness Diameter of copies - 2 Cut-Sheet Single part 105 to 215.9mm 70 to 297mm 52 to 105 g/m - 0.065 to 0.13 Paper (slip) (4.13” to 8.5”) (2.76” to 11.7”) (14 to 28lb) mm (Sip/ (0.0026” to Validation) 0.005”) Note 1 2 Single part 105 to 215.9mm 70 to 297mm 65 to 81 g/m - 0.08 to - (validation) (4.13” to 8.5”) (2.76” to 11.7”) (17 to 2
ملخص المحتوى في الصفحة رقم 17
1.5.1 Roll paper 1.5.1.1 Adjusting the Roll Paper Guide (Receipt) 1. Adjust paper guide A (1) to the paper width. Paper width: 2.75 inches (69.5 mm) or 3.00 inches (76.2 mm) Adjustment must be made for both Receipt and Journal. 1) When the printer is shipped, the paper width is set for wide roll paper (3 inch or 76.2 mm width) o425_89.jpg 1 2) To use narrow roll paper (2.73 inch or 69.5 mm width), hold up the roll paper guide and move it to the left to insert into the hole (1) at the lower fra
ملخص المحتوى في الصفحة رقم 18
1.5.1.2 Loading the Roll Paper (Receipt) Use roll paper that matches the specifications. Note: The printer must be turned on before installing the roll paper. 1. Fold the paper so it is exactly straight and even (1), and will not tear off jaggedly (2). OP425_01b.eps 2 1 2 2. Turn on the printer and open the printer cover. 3. Insert the roll paper as shown below. o425_55.jpg 4. Insert the tip of the paper into the paper inlet as far as it will go, and feed the roll paper until the paper comes ou
ملخص المحتوى في الصفحة رقم 19
5. Cut the roll paper. o425_92.jpg 6. Close the printer cover. Developer’s Guide: English 19 |
ملخص المحتوى في الصفحة رقم 20
1.5.1.3 Adjusting the Roll Paper Guide (Journal) 1. Adjust paper guide B (1) to the paper width. Paper width: 2.75 inches (69.5 mm) or 3.00 inches (76.2 mm) Adjustment must be made for both Receipt and Journal. 1) When the printer is shipped, the paper width is set for wide roll paper (3 inch or 76.2 mm width) o425_89.jpg 1 2) To use narrow roll paper (2.73 inch or 69.5 mm width), hold up the roll paper guide and move it to the right to insert into the hole (1) at the lower frame. o425_89.jpg 1
