ملخص المحتوى في الصفحة رقم 1
Proof Sign-off:
R4CD380/E850
R
KOW M.Arai K.Nishi
Unpacking and Setup Guide
K.Nishi
NOC K.Lee
Rev.C
COVER1.FM A4 size
4/6/05
®
Unpacking and Setup Guide
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Checking the Contents. . . . . . . . . . . . . . . . . . . . . . 5
Unpacking and Assembling
EPSON Stylus Pro 9800/9400 . . . . . . . . . . . . 5
Unpacking and Assembling
EPSON Stylus Pro 7800/7400 . . . . . . . . . . . 11
Setting up the Printer . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 2
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C COVER2.FM A4 size 4/6/05 Printer Parts Front view roll paper cover roll paper spindles paper lever mounting control panel brackets paper basket ink cartridge compartment front cover Rear view IEEE1394 interface connector USB interface connector AC inlet Optional interface card slot cover All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or tran
ملخص المحتوى في الصفحة رقم 3
Proof Sign-off: R4CD380/E850 R KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 The power cord or plug is damaged; liquid has Safety Instructions entered the printer; the printer has been dropped or the cabinet damaged; the printer does not operate normally or exhibits a Read all of these instructions before using your distinct change in performance. printer. Also be sure to follow all warnings and instructions marked on the printer. ❏ The int
ملخص المحتوى في الصفحة رقم 4
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 ❏ Shake an ink cartridge well before installing it Green and yellow - Earth for best results. Blue - Neutral Brown - Live If you have to fit a plug: As the colours of the mains lead of this appliance may not match coloured markings used to identify the terminals in a plug, please proceed as follows: The green and yellow wire must be connected to the terminal in the p
ملخص المحتوى في الصفحة رقم 5
Proof Sign-off: R4CD380/E850 R KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 Checking the Contents Unpacking and Assembling EPSON Stylus Pro 9800/9400 A Choosing a Place for the Printer B ❏ Leave adequate room for easy operation, maintenance, and ventilation as shown below. (Values in the illustration below are the C minimum.) D E F For EPSON Stylus Pro 9800/9400 only ❏ Leave at least 30 cm between the back of the printer and the wall. ❏ Cho
ملخص المحتوى في الصفحة رقم 6
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 ❏ Avoid locations near potential sources of Parts: interference such as loud speakers or cordless phones. B A ❏ Avoid locations near TVs, radios, air conditioners, or humidifiers. ❏ Keep the printer away from combustible substances. Deciding Where to Unpack the Printer C Before unpacking, read the followings: ❏ Setup and assemble the printer near to the chosen place
ملخص المحتوى في الصفحة رقم 7
Proof Sign-off: R4CD380/E850 R KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 Tools: ❏ Do not fasten the screws too tight. Leave a room to adjust the position when you fasten the screw on the other base upright. F G G A H I 2. Referring to step 1, secure the other side of the strut to the base (B). 3. Fasten four screws on the both sides of the base upright securely. F: Hex wrench This completes assembly of the base unit. Before attaching the
ملخص المحتوى في الصفحة رقم 8
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 2. Lift the box up and away from the printer. 3. Mount the printer on the base unit as shown Remove all items from the hollow (A and B) below. on the rear side of the printer. Caution: c Do not attempt to lift the printer unit with fewer than four people. Note: When you place the printer on the base unit, match the right end square of the printer (shown as 4 in the i
ملخص المحتوى في الصفحة رقم 9
Proof Sign-off: R4CD380/E850 R KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 4. Fasten the bottom of the printer and base unit Caution: c with wing nut, spring washers, and washers Watch your fingers when opening and (H). closing the front cover. L M N H 5. Release the front casters and the stabilizer knobs and move the printer to the place of use (a short distance away). Lock the casters and extend the stabilizer knobs after moving. L: Prot
ملخص المحتوى في الصفحة رقم 10
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 2. Turning the stitch side downward, spread the 6. Hook both ends of the center shaft (O) on the paper basket on the floor. upper basket hooks. O 3. Holding the rear shaft, pass it under the horizontal struts. 7. Insert the lower shafts into the holes on the bottom of the base unit as shown below. 4. Rotate the rear paper basket joints to enfold the bar that is not a
ملخص المحتوى في الصفحة رقم 11
Proof Sign-off: R4CD380/E850 R KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 Note: ❏ If the printer is not used or if you want to move the Set five paper feed support films at even intervals printer, insert the upper basket hooks. Make sure in the order shown in the figure. the lower shafts are in the upward position, and hook the basket rings on the upper basket hooks as shown below. b a Reusing the Packaging If you need to transport your pr
ملخص المحتوى في الصفحة رقم 12
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 ❏ Place the printer on a desk. If you cannot place Deciding Where to Unpack the Printer the printer on a desk, you will need the Stand. If you place your printer on a desk, follow the Before unpacking, read the followings: guidelines listed below. ❏ Setup and assemble the printer near to the ❏ Choose a desk that can hold the printer chosen place of use, as moving th
ملخص المحتوى في الصفحة رقم 13
Proof Sign-off: R4CD380/E850 R KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 3. Lift the box up and away from the printer. Using the Stand Remove all the items from the hollow (A and B) on the rear side of the printer. Checking the contents of the package Before assembling the Stand, check the contents of the package to make sure that all of the items shown are included, and are not damaged. Parts: Note: The ink cartridges included with your
ملخص المحتوى في الصفحة رقم 14
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 Accessories: 2. Assemble the left leg and left base in the same way as step 1. H I K J L M 3. Insert the bottom horizontal strut into the right and left bases as shown. Use the hex H: Base bolts (4) wrench (G) to fasten the strut with collars (K) and strut bolts (I). I: Strut bolts (2) J: Hex socket head bolts with washers (10) Note: After assembling the bases and bo
ملخص المحتوى في الصفحة رقم 15
Proof Sign-off: R4CD380/E850 R KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 4. Insert the top horizontal strut into the right 2. Mount the printer on the printer mount as and left legs. Use a screw driver to fasten the shown. strut with hex socket head bolts with washers (J). J J J 3. Fasten the bottom of the printer and the printer mount with wing screws (L) and washers (M) 5. This completes assembly of the Stand. Make sure each part of th
ملخص المحتوى في الصفحة رقم 16
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 3. Rotate the front paper basket joints to enfold Attaching the Paper Basket the bar which is not attached to the fabric as shown (N). Then, snap the front paper basket 1. Insert the basket hooks into the slots on the joints onto the tips of the basket hooks at the rotary boards attached to the bottom front of the Stand. Make sure the joints are horizontal strut.
ملخص المحتوى في الصفحة رقم 17
Proof Sign-off: R4CD380/E850 R KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 3. Route the power cord through the clamps at Setting up the Printer the rear of the printer. The cord can be routed to either the left or right side. Connecting the Power Cord Note: Most illustrations shown in this section are for EPSON Stylus Pro 9800/9400, so they may vary in appearance from EPSON Stylus Pro 7800/7400. The instructions are the same, except as not
ملخص المحتوى في الصفحة رقم 18
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 ❏ Each slot can hold a particular color of ink. Be sure 2. Open the ink compartment cover, and make to install the ink cartridges in the correct slots sure that the ink lever is in the up position. according to the ink mode you choose. 1 2 3 4 5 6 7 8 3. Remove the package from an ink cartridge. No. EPSON Stylus Pro EPSON Stylus Pro 9800/7800 9400/7400 #1 Light Light
ملخص المحتوى في الصفحة رقم 19
Proof Sign-off: R4CD380/E850 R KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 6. After inserting all ink cartridges in their 2. Place the roll paper on a flat surface so that it corresponding slot, lower the ink levers. The unwinds in the direction shown. Slide the roll printer starts initial ink charging. paper onto the spindle and fully onto the fixed flange. 7. After a while, ink lever messages appear on the LCD. Raise or lower the ink leve
ملخص المحتوى في الصفحة رقم 20
Proof Sign-off: R4CD380/E850 L KOW M.Arai K.Nishi Unpacking and Setup Guide K.Nishi NOC K.Lee Rev.C ENGLISH.FM A4 size 4/6/05 6. Make sure that the Power light is not flashing, ❏ Adjust the feed strength by pressing the and then set the paper lever to the released Paper Feed buttons on the control panel. position. The LEVER RELEASED. LOAD PAPER When using thick, heavy, or curled paper, appears on the LCD panel. press the Paper Feed u button to increase the power. When using thin or light p
