ملخص المحتوى في الصفحة رقم 9
ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing the bit 002651 To remove the bit, first pull the locator out of the locking sleeve. 2 1 1. Locator 2. Locking sleeve 002658 Hook the neck of the bit with one of the holes on the locator and pull. The bit is thus easily removed. 1 2 1. Locator hole 2. Bit neck 002659 To install the bit, insert it as far as it will go through the open- ing in the soft rubb
ملخص المحتوى في الصفحة رقم 10
Fit the screw on the point of the bit and place the point of the OPERATION screw on the surface of the workpiece to be fastened. Apply pressure to the tool and start it. Withdraw the tool as soon as the clutch cuts in. Then release the switch trigger. CAUTION: • When fitting the screw onto the point of the bit, be careful not to push in on the screw. If the screw is pushed in, the clutch will engage and the screw will rotate suddenly. This could damage a workpiece or cause an injury. • Make sure
ملخص المحتوى في الصفحة رقم 11
ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Phillips bit 2 - 45 11
ملخص المحتوى في الصفحة رقم 12
Memo 12
ملخص المحتوى في الصفحة رقم 13
Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold 13 Cut
ملخص المحتوى في الصفحة رقم 14
Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Magazine/Newspaper Catalog Tool Distributor Other ( ) From dealer Other ( ) Store display 2. Use of the product is intended for? 4. Most favored points are? Construction trade Home maintenance Design Makita Brand Industrial maintenance Other ( ) Features Power Size
ملخص المحتوى في الصفحة رقم 15
Factory Service Centres Head Office: 1950 Forbes St., Whitby, Ontario, L1N 7B7 (905) 571 - 2200 1-800-263-3734 Regional Office: 11771 Hammersmith Way, Richmond B.C. V7A 5H6 (604) 272 - 3104 1-800-663-0909 Regional Office: 6389 boul, Couture, St. Leonard, Quebec (Montreal) H1P 3J5 (514) 323 - 1223 1-800-361-7049 Dartmouth: 202 Brownlow Avenue Dartmouth, N.S., B3B 1T5 (902) 468 - 7064 1-888-625-4821 Ville St. Laurent: 1140 Rue Bégin, Ville St. Laurent, Quebec (Montreal) H4R 1X1 (514) 745 -
ملخص المحتوى في الصفحة رقم 16
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres. If inspection shows the trouble is caused by defective workmanship or material, M
ملخص المحتوى في الصفحة رقم 1
Drywall Screwdriver
MODEL 6812
002602
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ملخص المحتوى في الصفحة رقم 2
SPECIFICATIONS Model 6812 Self drilling screw 5 mm (3/16”) Capacities Drywall screw 5 mm (3/16”) No load speed (RPM) 1,500 - 4,500/min. Overall length 294 mm (11-5/8”) Net weight 1.3 kg (2.9 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire
ملخص المحتوى في الصفحة رقم 3
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
ملخص المحتوى في الصفحة رقم 4
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
ملخص المحتوى في الصفحة رقم 5
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD201-2 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current 5
ملخص المحتوى في الصفحة رقم 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002610 Depth adjustment A The depth can be adjusted by turning the locking sleeve. Turn it in “A” direction for less depth and in “B” direction for more depth. One full turn of the locking sleeve equals 1.5 mm (1/16”) change in depth. B 1 1. Locking sleeve 002615 Adjust the locking sleeve so that the distance between the tip of the locator and the screw
ملخص المحتوى في الصفحة رقم 7
002626 Switch action 1 CAUTION: 2 • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. 1. Lock button For continuous operation, pull the switch trigger and then 2. Switch trigger push in the lock button. To stop the tool from the locked position, pull the switch trig- ger fully, then release it. NOTE: • Even with the switc
ملخص المحتوى في الصفحة رقم 8
002639 Refer to the figure for the relationship between the number (rpm) settings on the adjusting dial and the kind of work. 4500 A range: C For work that requires a subtle speed control such as center- B 1500 A ing or final fastening. 12 3 4 5 B range: Dial setting Use when screws/drywall boards might be damaged with C range speed. C range: For regular fastening work. NOTE: • The above figure shows standard applications. They may differ under certain conditions. CAUTION: • If the tool is opera
