ملخص المحتوى في الصفحة رقم 1
Quick Start Guide
FOR MODEL NUMBERS:
iCAM4000
iCAM4000R
iCAM4010-E1
iCAM4010R-E1
iCAM4010-H1
iCAM4010R-H1
COPYRIGHT © 2007 LG ELECTRONICS USA INC, ALL RIGHTS RESERVED.
LG IrisAccess™ 4000: iCAM4000 Quick Start Guide
The content of this document is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by LG Electronics USA
Incorporated. LG Electronics USA Incorporated assumes no responsibility or liability for any errors or inaccur
ملخص المحتوى في الصفحة رقم 2
Packing List 1 What’s in the box • iCAM4000 - IrisCamera • Power Adapter Input: 110~240V AC - 1.5AMP 50/60Hz Output: 12V DC - 5.0AMP • Power Cable for 110V • CAT5 Ethernet Cable • Quick Start Guide • Security Screw Wrench Required Equipment (not included with iCAM4100) • Server Computer (refer to the Hardware Manual for details) • Ethernet Switch • Ethernet Wiring • Uninterruptible Power Supply
ملخص المحتوى في الصفحة رقم 3
iCAM4000 in the IrisAccess System 2 The iCAM4000 is a two-eye iris camera used to capture the iris images of the user. The iCAM includes an alignment indicator behind the mirror and voice prompts to assist the user. When used in a typical access control application, the iCAM will be placed near the secured portal and provides the means for the system to identify the user requesting entry. The iCAM can be used in enrollment mode using the IrisEnroll application (included with EAC software)
ملخص المحتوى في الصفحة رقم 4
Installation Requirements 3 bottom of mirror 61” 56” (155mm) (142mm) floor • The recommended mounting height for the iCAM4000 is 142cm (56 inches) from the floor to the bottom of the unit. This mounting height can be adjusted to accommodate the height of the average user at the installed location. • High amounts of ambient light must be avoided. Intense light sources such as sunlight or halogen lamps may reduce the image capture performance of the iCAM, this may result in an
ملخص المحتوى في الصفحة رقم 5
iCAM4000 Installation 4 1. Remove the two security screws (use included security bit wrench) from the bottom of the iCAM 2. While gently pulling the cover upward on the back plate, pull forward. 3. Position the iCAM back plate on the desired wall near the secured door and mark the holes as the figure below illustrates. The recommended height from the floor to bottom of unit is 142cm (56”), however the installation height can be adjusted depending on average user height.
ملخص المحتوى في الصفحة رقم 6
iCAM4000 Installation (cont’d) 5 4. When recessed mounting, leave 6mm (1/4”) of extra space above the marked hole so when mounting the back plate it allows the iCAM to slide down onto the installation plate tabs. 5. Route the power line, network line, and other necessary cables through the back plate hole. 6. Use the appropriate fasteners for the material in which the iCAM will be mounted, secure the back plate. 7. Attach the wires from the 12VDC power supply to the screw termin
ملخص المحتوى في الصفحة رقم 7
iCAM4000 Configuration 6 Changing the IP Address of the iCAM * Note: The IP Address of each iCAM must be changed individually. Do not connect more than one un-configured iCAM to the network at any one time to avoid IP Address conflicts. Any computer with a web browser which supports graphics (ex. Internet Explorer) can be used to configure the iCAM4000/4100. 1. Set the computer to the static IP of 192.168.5.1 - subnet 255.255.255.0 2. Open the web brows
ملخص المحتوى في الصفحة رقم 8
iCAM4000 Configuration (cont’d) 7 5. Select Network Settings. 6. Enter the new IP address for the iCAM (default = 192.168.5.100) 7. Enter the new Subnet Mask for the iCAM (default = 255.255.255.0) 8. Enter the new Broadcast Address for the iCAM (default = 192.168.5.255) 9. Enter the new Default Gateway for the iCAM. (default = 192.168.5.254) 10. Click OK to save changes and to open network settings verify screen. If the new iCAM IP address is still on the same subnet as the computer:
ملخص المحتوى في الصفحة رقم 9
iCAM4000 Configuration (cont’d) 8 Once all iCAMs have been configured Once all iCAMs have been configured, the computer IP Address can then be changed back to its original IP Address or to the new IP Address as required to communicate to the rest of the IrisAccess™ system. SmartCard Integration • The iCAM4010-E1 and iCAM4010R-E1 have a built-in Integrated Engineering Smart ID smart card reader, and the iCAM4010-H1 and iCAM4010R-H1 have a built-in HID iClass smart card reader. • Th
ملخص المحتوى في الصفحة رقم 10
Technical Support 9 Technical Support Additional information and Technical assistance is available on the LG Electronics – Iris Technology Division’s support web site at www.lgiris.com, click on Support & Service then Technical Support.
