Audiovox P-150 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

by AUDIOVOX
INSTALLATIONMANUAL
COMPACTDISCCHANGERSYSTEM
MODEL P-150

ملخص المحتوى في الصفحة رقم 2

PACKINGLIST MAINUNIT Changer INSTALLATIONPARTS Bracket (L) Bracket (R) Hexagonal bolt with washer 5 Meter Din Cable (M5 x 10) 1 pc. 1 pc. 4 pcs. 1 pc. Self-tapping screw Seals (A) Seals (B) (M5 x 12) 4 pcs. 1 pc. 1 pc. OTHERACCESSORIES CD Magazine Index seal sheet Installation Manual Owner'sguide 1 pc. 1 pc. 1 pc. 1 pc. 1

ملخص المحتوى في الصفحة رقم 3

BEFOREINSTALLINGTHEUNIT TransportLockScrews The mechanism in the CD changer is "locked" into place during shipment by the transport screws. Be sure to remove the screws prior to installation. Caution After removing the transport lock screws, place the supplied seals (A) over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction. InstallationandWiringPrecautions To prevent a short-circuit, 1 l Be sure to turn off the ignition and remove the negative (

ملخص المحتوى في الصفحة رقم 4

INSTALLATION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. CAUTION Aftersettingthebuilt-inanti-vibrationsprings,placethesuppliedSeals(B)overtheholes. Thesesealsareusedtokeepdust,whic

ملخص المحتوى في الصفحة رقم 5

PROCEDUREFORVERTICALINSTALLATION Note If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2. Set the 4 anti-vibration springs to position "V". Attachbracket(L)andbracket(R)toeachsideoftheunit, 1 2 using the hexagonal bolts with washer base (M5 x 8). NOTE: Use seals (A) to cover unused mounting holes on sides of unit. position "V" Bracket (L) Bracket (R) Hexagonal bolt with washer base (M5 x 8) Determine the mounting loca

ملخص المحتوى في الصفحة رقم 6

PROCEDURE FOR 45°ANGLE INSTALLATION Note If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2. Set the 4 anti-vibration springs to position "45°". Attachbracket(L)andbracket(R)toeachsideoftheunit, 1 2 using the hexagonal bolts with washer base (M5 x 8). NOTE: Use seals (A) to cover unused mounting holes on sides of unit. position "45°" Bracket (L) Bracket (R) Hexagonal bolt with washer base (M5 x 8) Determine the mount

ملخص المحتوى في الصفحة رقم 7

DIN cable (8-pin) VEHICLEWIRING Mating 8-pin DIN socket on rear of compatible radio chassis (see note 1 below). Car Stereo with CD Changer Controls CD changer NOTE: 1. Check with your Prestige car audio dealer to be sure your stereo is directly compatible with this CD changer. 2. Wiring instructions for use with FM Modulator/ Commander Systems are included with the P-MC3 and P-MCR4 accessories. 6

ملخص المحتوى في الصفحة رقم 8

© 1997 AUDIOVOX CORP., HAUPPAUGE, N.Y Printed in Korea Form No. 128-5203