Kohler K-4346 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Installation & User Guide
Dual-Flush Toilet
K-3735 K-3736
K-19896 K-4346
1102602-A2-A

ملخص المحتوى في الصفحة رقم 2

Tools and Materials Thank You For Choosing Kohler Company We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start installation. If you encounter any installation or performance problems, please don’t hesitate to contact us. Our phone numbers are listed on the back cover. Thanks again for choosing Kohler Company. Before You Begin CAUTION: Risk of personal injury or product damage. Handle with care. Vitreous china can break or chip if the p

ملخص المحتوى في الصفحة رقم 3

Installation 1 Remove the existing toilet: Turn off the water supply and flush the toilet, then sponge out all remaining water from the cistern. Disconnect the supply shut-off valve (if present), and remove the old pan and cistern. CAUTION: Risk of hazardous gases. If the new toilet is not installed immediately, temporarity stuff a rag in the closet flange. 2 Define the position of connector: Place the connector onto the pan, position between outlet and waste pipe. Case 1 Finished Case 2 Fini

ملخص المحتوى في الصفحة رقم 4

Installation 4 Drill 3/8” (10 mm) mounting hole 5 Install the washer and insert the hexagon between the mark locations on the screw into the bracket then tighten the floor and insert the anchor. screw. Hexagon Lag Screw Bracket Washer Anchor Anchor 6 Install the sleeves, 7 Position the cistern on the pan by centering the gasget tighten the screw on the pan inlet. Assemble the retaining washer and and attach the sealing washer to the screw. Securely tighten the caps. screws so the cistern is leve

ملخص المحتوى في الصفحة رقم 5

Installation 8 Connect the supply shut-off valve to the supply hose and connect supply hose to toilet supply shank. Water Supply Hose Water Supply Hose Bottom Inlet Type Rear Inlet Type 9 In cistern. Rear Water Inlet Bottom Water Inlet K-19896 K-3736 Stop Valve Tank Hose Bottom Water Inlet Rear Water Inlet Optional 148794A-NA K-3735, K-4346 Kohler Co. 5 1102602-A2-A

ملخص المحتوى في الصفحة رقم 6

Install the Push Buttons 1 Remove the tape and protective pad. 2 Press down on the large button. protective pad. Tank Cover 3 Pull out and remove the small button. 4 Pull out and remove the large button. 5 Press the large button on to the black 6 Press the small button on to the green rod. rod. Small Button Large Button Green Rod Black Rod 7 Insert the rod into the holes in the push 8 Press down on the push buttons until button housing. they click into place. 1102602-A2-A 6 Kohler Co.

ملخص المحتوى في الصفحة رقم 7

Install Flush Valve 1 Release flush valve by turn right and pull straight up on the canister. 2 1 2 Assembly flush valve by push straight down into the canister and turn left. 1 2 Kohler Co. 7 1102602-A2-A

ملخص المحتوى في الصفحة رقم 8

New Zealand Kohler New Zealand Ltd. Phone: 64 9 980 6888, 0 800 100 382 Fax: 64 9 980 6899 Australia Kohler Co. Phone: 61 1300 362 284 Fax: 61 1300 652 284 © 2008 Kohler Co. 1102602-A2-A