Hans Grohe ShowerArc 26396001 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Installation Instructions / Warranty
ShowerArc
26396001

ملخص المحتوى في الصفحة رقم 2

ShowerArc 26396001 Minimum ceiling height – 90 1/2” 2

ملخص المحتوى في الصفحة رقم 3

Installation Considerations • For best results, Hansgrohe recommends on the left and the cold supply must enter that this unit be installed by a licensed, the valve on the right. If the valve is cross- professional plumber. connected, it cannot function correctly. • Please read over these instructions thor- • The difference in water pressure between oughly before beginning installation. the hot and cold supplies should not Make sure that you have all tools and sup- exceed 10 psi or the the

ملخص المحتوى في الصفحة رقم 4

Installation in 90º corner: Instructions begin on page 5 Wall-to-wall installation Requires 26397000 installation kit (included): Instructions begin on page 13. Roughing-in The ShowerArc requires 1/2” NPT female fittings, recessed 3/8” behind the surface of the finished wall, for the hot and cold water supplies for the thermostatic mixing valve. 4

ملخص المحتوى في الصفحة رقم 5

Installation in 90º corner Only one set of supplies is required – do not install two sets of supplies. The thermostatic mixing valve may be installed on either wall. This diagram shows both possible positions for the installation. 5

ملخص المحتوى في الصفحة رقم 6

Installation in 90º Corner Seal the wall around the supplies with waterproof sealant. Failure to seal the wall can lead to possible water damage. 1 2 3 4 6

ملخص المحتوى في الصفحة رقم 7

5 6 7 8 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 7

ملخص المحتوى في الصفحة رقم 8

9 10 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 11 Be careful not to drill into water lines! 12 6 mm 8

ملخص المحتوى في الصفحة رقم 9

13 14 15 16 9

ملخص المحتوى في الصفحة رقم 10

17 18 19 20 1 2 6 mm 10

ملخص المحتوى في الصفحة رقم 11

21 22 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 24 23 2 1 6 mm 11

ملخص المحتوى في الصفحة رقم 12

25 26 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. Turn to page 22 to continue the installation. 12

ملخص المحتوى في الصفحة رقم 13

Wall-to-Wall Installation Only one set of supplies is required – do not install two sets of supplies. The thermostatic mixing valve may be installed on either wall. The diagram shows both possible positions for the installation. 13

ملخص المحتوى في الصفحة رقم 14

Wall-to-Wall Installation Seal the wall around the supplies with waterproof sealant. Failure to seal the wall can lead to possible water damage. 1 2 3 4 14

ملخص المحتوى في الصفحة رقم 15

5 6 7 8 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 15

ملخص المحتوى في الصفحة رقم 16

9 10 11 12 2 Seal the wall around the anchors with waterproof 6 mm sealant. Failure to seal the wall can lead to possible water damage. 1 Be careful not to drill into water lines! 16

ملخص المحتوى في الصفحة رقم 17

13 14 Install the 26397000 mounting set 15 16 17

ملخص المحتوى في الصفحة رقم 18

17 18 90 20 19 XX = XX 18

ملخص المحتوى في الصفحة رقم 19

21 22 1 2 6 mm 23 24 M6x8 SW 3 mm 19

ملخص المحتوى في الصفحة رقم 20

25 26 2. M6x8 1. 3. SW 3 mm M6x60 Install the 26397000 mounting set 27 28 2 Seal the wall around the an- 1 chors with waterproof sealant. 6 mm Failure to seal the wall can lead to possible water damage. 20