ملخص المحتوى في الصفحة رقم 1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
Power Planer
1911B
001602
DOUBLE INSULATION
IMPORTANT: Read Before Using. 1
ملخص المحتوى في الصفحة رقم 2
ENGLISH (Original instructions) SPECIFICATIONS Model 1911B Planing width 110 mm Planing depth 2 mm -1 No load speed (min) 16,000 Overall length 355 mm Net weight 4.3 kg Safety class /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003 END201-5 ENG222-2 Vibration Symbols The vibration total value (tri-axial
ملخص المحتوى في الصفحة رقم 3
And are manufactured in accordance with the following 6. Do not expose power tools to rain or wet standards or standardised documents: conditions. Water entering a power tool will EN60745 increase the risk of electric shock. The technical documentation is kept by our authorised 7. Do not abuse the cord. Never use the cord for representative in Europe who is: carrying, pulling or unplugging the power tool. Makita International Europe Ltd. Keep cord away from heat, oil, sharp edges or Michi
ملخص المحتوى في الصفحة رقم 4
Power tool use and care could give the operator an electric shock. 18. Do not force the power tool. Use the correct 3. Use clamps or another practical way to secure power tool for your application. The correct and support the workpiece to a stable platform. power tool will do the job better and safer at the Holding the work by hand or against your body rate for which it was designed. leaves it unstable and may lead to loss of control. 19. Do not use the power tool if the switch does 4. Rags
ملخص المحتوى في الصفحة رقم 5
To stop the tool from the locked position, pull the switch FUNCTIONAL DESCRIPTION trigger fully, then release it. For tool with lock-off button To prevent the switch trigger from being accidentally CAUTION: pulled, a lock-off button is provided. • Always be sure that the tool is switched off and To start the tool, depress the lock-off button and pull the unplugged before adjusting or checking function on switch trigger. Release the switch trigger to stop. the tool. Adjusting depth
ملخص المحتوى في الصفحة رقم 6
Place the blade on the gauge base so that the blade 1. Adjust plate edge is perfectly flush with the inside edge of the gauge 2. Screws 5 plate. Place the adjust plate on the blade, then simply 3. Heel of adjust plate press in the heel of the adjust plate flush with the back 6 7 4. Back side of 1 side of the gauge base and tighten two screws on the gauge base 2 adjust plate. Now slip the heel of the adjust plate into the 5. Blade edge drum groove, then fit the drum cover on it. Tighten
ملخص المحتوى في الصفحة رقم 7
For European countries only Chamfering When you wish to perform clean planing operation, To make a cut as shown in the figure, align the ''V'' connect a Makita vacuum cleaner to your tool. Install the groove in the front base with the edge of the workpiece nozzle on the tool using the screws. Then connect a hose and plane it as shown in the figure. of the vacuum cleaner to the nozzle as shown in the figures. 1. Vacuum cleaner 1 001609 004951 1. Align the (Y) groove with the O
ملخص المحتوى في الصفحة رقم 8
NOTE: 1. Wing nut 1 • Some items in the list may be included in the tool 2. Blade (A) package as standard accessories. They may differ 3. Blade (B) from country to country. 4. Side (C) 5. Side (D) 4 2 5 3 001611 Immerse the dressing stone in water for 2 or 3 minutes before sharpening. Hold the holder so that the both blades contact the dressing stone for simultaneous sharpening at the same angle. 001612 To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspe
ملخص المحتوى في الصفحة رقم 9
9
ملخص المحتوى في الصفحة رقم 10
10
ملخص المحتوى في الصفحة رقم 11
11
ملخص المحتوى في الصفحة رقم 12
Makita Corporation Anjo, Aichi, Japan 12 883098F226 www.makita.com
