ملخص المحتوى في الصفحة رقم 1
82 mm (3-1/4") MODEL Mi02
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPEC IF I CAT IONS
Planing width 1 Planing depth 1 No load speed i Overall length 1 Net weight
(RPM)
295 mm I1 1 518") 2 5 kg (5 5 lbsi
82 mm (3-114") 1 1 mm (1/32"1 16,000
* Manufacturer reserves the right to change specifications without notice
* Note Specifications may differ from country to country
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
ملخص المحتوى في الصفحة رقم 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don‘t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are t
ملخص المحتوى في الصفحة رقم 4
ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work area. 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- fore operation. 3. Handle the blades very carefully. 4. Be sure the blade installation bolts are securely tightened before operation. 5. Hold the tool firmly with both hands. 6. Keep hands away from rotating parts. 7. Before using the tool on an actual workpiece, let it run for a while. Watch for vib
ملخص المحتوى في الصفحة رقم 5
Removing or installing mini planer blades CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blade, loosen the three installation bolts with the socket wrench. it Remove the blade by carefully sliding from on the end of the drum. WARNING: Be extremely careful not to be cut by the sharp edges. To install the blade, slide it inward from the end of the drum into the gap between the drum and the set plate. Adjust t
ملخص المحتوى في الصفحة رقم 6
NOTE : A mini planer blade has a cutting edge on both sides, making it reversible for double blade life and greater convenience. CAUTION : Tighten the blade installation bolts carefully when attaching the blades to the tool. A loose installation bolt can be dangerous. Always check to see they are tightened securely. Blade adjustment using blade gauge Unscrew the three installation bolts. Remove the drum cover, the mini blade Heel of and the adjusting plate/set plate. Loosen adjusting
ملخص المحتوى في الصفحة رقم 7
For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the reat base. Below are some examples of proper and improper settings. (A) Front base (Movable shoe) (6) Rear base (Stationary shoe) Although this side view cannot show it, the edges of the blades run perfectly Correct 1 setting bzT parallel to
ملخص المحتوى في الصفحة رقم 8
Planing operation First, rest the tool front base flat upon the workpiece surface without the blades mak- ing any contact. Switch on and wait until the blades attain full speed. Then move the tool gently forward. Apply pressure on the front of tool at the start of planing, and at the back at the end of planing. Planing will be easier if you incline the workpiece in stationary fashion, so that you can plane somewhat downhill. The speed and depth of cut determine the kind of finish. The
ملخص المحتوى في الصفحة رقم 9
You may wish to add to the length of the fence by attaching an extra piece of wood. Convenient holes are provided in the fence for this purpose, and also for attaching an extension guide (optional accessory). I I NOTE : When planing, move the tool with the edge fence flush with the side of the workpiece. Otherwise uneven planing may result. Max. shiplapping depth is 9 mm (1 1/32"). Chamfering To make a cut as shown at the right, align the "V" groove in the front base with the edge of
ملخص المحتوى في الصفحة رقم 10
ACCESSORI ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Planer blade 0 Guide rule Part No. 191455-1 Part No. 793209-0 0 Screwdriver 0 Dust bag assembly Part No. 122269-7 Part No. 783002-8 0 Socket wrench 0 Blade gauge Part No. 798145-3
ملخص المحتوى في الصفحة رقم 11
Sep -17 -'87 US 82 mm (3-1/4") POWER PLANER Model MI02 Note The switch, noise suppressor and other part configurations may differ from country to country 11
ملخص المحتوى في الصفحة رقم 12
Sep.-17-'87 US ITEM A:D DESCRIPTION 'LtM DESCRIPTION MACHINE MACHINE ~ 1 1 Tapping Screw 81 4x40 28 2 Tapping Screw 8T 4x60 2 1 Chip Cover 29 1 Bracket 3 2 Tapping Screw BT 4x14 30 Tapping Screw BT 4x25 6 4 1 Rear Cover 31 1 V Pulley 4-2OL 5 1 Knob 46 32 1 Belt Cover 6 1 Scale Plats 33 1 Rubber Pin 4 7 1 Flat Washer 10 34 2 Tapping Screw BT 4x25 8 1 Main Frame 35 1 Poly V Belt 4-241 9 1 Name Plate 36 1 v Pulley 4-37 1 1 IO Cord Guard 37 Ball Bearing 600022 11 1 Cord 38 1 Rubber
