ملخص المحتوى في الصفحة رقم 1
110 mm (4-318") MODEL 1911B
INSTRUCTION MANUAL
DOUBLE
IIYSUL ATION
No load speed Overall length Net weight
Planing width Planing depth
IRPMI
110 mm 14 3/8"1 2 mm (1116"l 16,000 355 mm 114") 4 2 kg (9 3 Ibs)
* Manufacturer reserves the right to change specifications without notice
Note Specifications may differ from country to country
ملخص المحتوى في الصفحة رقم 2
I M PO RTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presen
ملخص المحتوى في الصفحة رقم 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don‘t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are t
ملخص المحتوى في الصفحة رقم 4
ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work area. 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- fore operation. 3. Handle the blades very carefully. 4. Be sure the blade installation bolts are securely tightened before operation. 5. Hold the tool firmly with both hands. 6. Keep hands away from rotating parts. 7. Before using the tool on an actual workpiece, let it run for a while. Watch for vib
ملخص المحتوى في الصفحة رقم 5
Removing or installing planer blades CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the blade. The blade is secured with four bolts. Re- move the inner two bolts entirely with the socket wrench and loosen the outer two bolts two turns each. Fig. 1 Press down on the pin in the middle of the drum with one end of the socket wrench handle. The blade can be pushed and so as to be removed. (If the jiggled out blade becomes so short that
ملخص المحتوى في الصفحة رقم 6
Align the blade edge with the mark and make the drum stationary by means of the stopper pin. Place the leveller over the rear Stopper pin base and blade, and press the leveller down slightly. Release the stopper pin. When released When secured ~ Fig. 4 I Turn the drum in the direction of the arrow (Fig. 6) to check the blade protru- Leveller sion, holding the leveller flush against the - blade and rear base. The blade edge should just contact the underside of the leveller. When
ملخص المحتوى في الصفحة رقم 7
For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base. Below are some examples of proper and improper settings. (A) Front base (Movable shoe) (B) Rear base (Stationary shoe) Although this side view cannot show it, the edges of the blades run perfectlv parallel to the rear base surface.
ملخص المحتوى في الصفحة رقم 8
Planing operation First, rest the tool front base flat upon the workpiece surface without the blades mak- ing any contact. Switch on and wait until the blades attain full speed. Then move the tool gently forward. Apply pressure on the front of tool at the start of planing, and at the back at the end of planing. Planing will be easier if you incline the workpiece in stationary fashion, so that you can plane Fig. 9 somewhat downhill. The speed and depth of cut determine the kind of fin
ملخص المحتوى في الصفحة رقم 9
First, loosen the two wing nuts on the holder and insert the blades (A) and (B) so that they contact the sides (C) and (D). I Wing nut Then tighten the wing nuts. Side (C) Fig. 1 Immerse the dressing stone in water for 2 or 3 minutes before sharpening. Hold the holder so that the blades both contact the dressing stone for simultaneous sharpening at the same angle. Fig. Id MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform
ملخص المحتوى في الصفحة رقم 10
ACC ESSO R I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Planer blade Planer blade Width : 110 mm (4-3/8") (Material : Tungsten-carbide) Part No. 793008-8 Width: 110 mm (4-3/8") Part No. 793009-6 Dressing stone 0 Guide rule Part No. 7940
ملخص المحتوى في الصفحة رقم 11
Dec.-10-'87 EN 110 mm (4-3/8") POWER PLANER Model 1911B Note: The switch. noise suppressor and other part configurations may differ from country to country. 11
ملخص المحتوى في الصفحة رقم 12
Mar -31-89 US ITEM A:D DESCRIPTION MB 11 Cord 33 1 ARMATURE ASSEMBLY 21 1 Cord Guard IWith Items 28 & 32 - 361 Strain Relief 34 1 Fan 68 Pan Head Screw M4x18 IWith Washerl 35 1 Dust Seal 10 51 1 Switch 36 1 Ball Bearing 6200LLB Handle Cover 37 1 Bracket Pan Head Screw M4x40 IWilh Washer1 38 6 Pan Head Screw M4x30 (With Washer1 Pan Head Screw M4x30 (With Washerl 39 1 V Pulley 4-24L 10 1 Name Plate 40 1 Poly VBelf 4-272 11 4 Rivet 0-5 41 1 Belt Cover 12 2 Brush Holder 42 1 Pan Head Sc
