ملخص المحتوى في الصفحة رقم 1
Dell OptiPlex 9010 All-In-One
Owner's Manual
Regulatory Model: W04C
Regulatory Type: W04C001
ملخص المحتوى في الصفحة رقم 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2012 Dell Inc. ™ ™ ™ ™ ™ ™ Trademarks used in this text: Dell , the Dell logo, Dell Precision , OptiPlex , Latitude , PowerEdge , PowerVault , ™ ™ ™ ™ ™ ™ ™ ™ Pow
ملخص المحتوى في الصفحة رقم 3
Contents Notes, Cautions, and Warnings...................................................................................................2 1 Working on Your Computer.......................................................................................................7 Before Working Inside Your Computer.....................................................................................................................7 Turning Off Your Computer...................................................
ملخص المحتوى في الصفحة رقم 4
Removing the Input/Output Board Shield...............................................................................................................24 Installing the Input/Output Board Shield................................................................................................................27 Removing the Power-Button Board........................................................................................................................27 Installing the Power-Button Board......
ملخص المحتوى في الصفحة رقم 5
7 Contacting Dell .........................................................................................................................65
ملخص المحتوى في الصفحة رقم 6
6
ملخص المحتوى في الصفحة رقم 7
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse orde
ملخص المحتوى في الصفحة رقم 8
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components. Turning Off Your Computer CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1. Shut down the operating system: – In Windows 7: Click
ملخص المحتوى في الصفحة رقم 9
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe Removing the VESA Stand 1. Follow the procedures in Before Working Inside Your Computer. 2. Place the computer on a flat surface, display side facing downwards. 3. Using a plastic scribe, release t
ملخص المحتوى في الصفحة رقم 10
5. Remove the screws that secure the VESA stand to the computer and lift the VESA stand away from the computer. Installing the VESA Stand 1. Align and place the VESA stand on the back of the computer. 2. Tighten the screws to secure the VESA stand to the computer. 3. Place and press the VESA cover on the computer, till it clicks into place. 4. Follow the procedures in After Working Inside Your Computer. Removing the Back Cover 1. Follow the procedures inBefore Working Inside Your Computer. 2. Re
ملخص المحتوى في الصفحة رقم 11
4. Lift the cover and remove it from the computer using the notches near the input/output panel. Installing the Back Cover 1. Place the cover on the back of the computer using the notches near the input/output panel. 2. Tighten the screws to secure the back cover to the computer. 3. Install the VESA stand. 4. Follow the procedures in After Working Inside Your Computer. Removing the Memory 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) VESA stand b) back cover
ملخص المحتوى في الصفحة رقم 12
3. Lift the memory shield outwards. 4. Pry the retention clips away from the memory module until it pops up. Lift and remove the memory module from its connector. Installing the Memory 1. Align the notch on the memory-card with the tab in the system-board connector. 2. Press down on the memory module until the release tabs spring back to secure them in place. 3. Place the memory shield back into its place. 4. Install the: a) back cover b) VESA stand 5. Follow the procedures in After Working Ins
ملخص المحتوى في الصفحة رقم 13
Installing the VESA Mount Bracket 1. Align and place the bracket on the back of the computer. 2. Tighten the screws to secure the VESA mount bracket to the computer. 3. Install the: a) back cover b) VESA stand 4. Follow the procedures in After Working Inside Your Computer. Removing the Converter Board 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) VESA stand b) back cover 3. Disconnect the backlight and converter cables from the converter board. Remove the scr
ملخص المحتوى في الصفحة رقم 14
Installing the Converter Board 1. Place the convertor board into its place. 2. Tighten the screws that secure the converter board to the computer. 3. Connect the backlight and converter cables to the converter board. 4. Install the: a) back cover b) VESA stand 5. Follow the procedures in After Working Inside Your Computer. Removing the System-Board Shield 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) VESA stand b) back cover c) VESA mount bracket 3. Remove th
ملخص المحتوى في الصفحة رقم 15
Removing the Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) VESA stand b) back cover c) system-board shield 3. Press the release latch away from the battery. The battery pops out from the socket, lift the coin-cell battery out of the computer. Installing the Coin-Cell Battery 1. Place the coin-cell battery into its slot on the system board. 2. Press the coin-cell battery downward until the release latch springs back into place and secures it
ملخص المحتوى في الصفحة رقم 16
4. Slide the optical drive outwards. Disconnect the optical-drive cable. 5. Lift the optical drive from the computer. 6. Remove the screws that secure the optical-drive bracket to the optical drive. Remove the optical-drive bracket from the optical drive. 16
ملخص المحتوى في الصفحة رقم 17
Installing the Optical Drive 1. Place the optical-drive bracket on the optical drive. 2. Tighten the screws that secure the optical-drive bracket to the optical drive. 3. Align and slide the optical drive into its slot. 4. Connect the optical-drive cable. 5. Tighten the screws that secure the optical drive to the computer. 6. Install the: a) VESA mount bracket b) back cover c) VESA stand 7. Follow the procedures in After Working Inside Your Computer. Removing the Hard Drive 1. Follow the procedu
ملخص المحتوى في الصفحة رقم 18
4. Remove the screw that secures the hard-drive bracket to the system board. Slide and lift the hard-drive bracket away from the computer. 5. For a 2.5–inch hard drive, remove the screws that secure the hard drive to the hard-drive bracket. Slide the hard drive from the hard-drive bracket. Remove the screws that secure the hard-drive case to the hard drive. 6. For a 3.5–inch hard drive, remove the screws that secure the hard drive to the hard-drive bracket. Slide the hard drive from the hard-
ملخص المحتوى في الصفحة رقم 19
a) VESA mount bracket b) back cover c) VESA stand 6. Follow the procedures in After Working Inside Your Computer. Removing the Intrusion Switch 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) VESA stand b) back cover c) VESA mount bracket d) system-board shield 3. Disconnect the intrusion cable from the connector on the system board. Unthread the cable from the notches on the computer. 4. Remove the screws that secure the intrusion switch to the chassis. Lift
ملخص المحتوى في الصفحة رقم 20
Installing the Intrusion Switch 1. Place the intrusion switch on the computer and tighten the screw to secure it to the chassis. 2. Thread the cable along the notches on the chassis and connect the intrusion switch to the connector on the system board. 3. Install: a) system-board shield b) VESA mount bracket c) back cover d) VESA stand 4. Follow the procedures in After Working Inside Your Computer. Removing the Wireless Local Area Network (WLAN) Card 1. Follow the procedures in Before Working I
