ملخص المحتوى في الصفحة رقم 1
Dell OptiPlex 3010 Desktop
Owner's Manual
Regulatory Model: D07D
Regulatory Type: D07D001
ملخص المحتوى في الصفحة رقم 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2012 Dell Inc. ™ ™ ™ ™ ™ ™ Trademarks used in this text: Dell , the Dell logo, Dell Precision , OptiPlex , Latitude , PowerEdge , PowerVault , ™ ™ ™ ™ ™ ™ ™ ™ Pow
ملخص المحتوى في الصفحة رقم 3
Contents Notes, Cautions, and Warnings...................................................................................................2 1 Working on Your Computer.......................................................................................................7 Before Working Inside Your Computer.....................................................................................................................7 Turning Off Your Computer...................................................
ملخص المحتوى في الصفحة رقم 4
Installing The Power Supply...................................................................................................................................29 Removing the System Board...................................................................................................................................30 Installing the System Board....................................................................................................................................31 Removing The PSU T
ملخص المحتوى في الصفحة رقم 5
Memory address line failure at address, read value expecting value ............................................................51 Memory allocation error..................................................................................................................................51 Memory data line failure at address, read value expecting value...................................................................51 Memory double word logic failure at address, read value expecting value..........
ملخص المحتوى في الصفحة رقم 6
6
ملخص المحتوى في الصفحة رقم 7
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse orde
ملخص المحتوى في الصفحة رقم 8
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components. Turning Off Your Computer CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1. Shut down the operating system: – In Windows 7: Click
ملخص المحتوى في الصفحة رقم 9
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Removing the Cover 1. Follow the procedures in Before Working Inside Your Computer. 2. Pull up the cover-release latch at the side of the computer. 3. Lift the cover upward to a 45–degree angle and remove it from the computer. Related Links Installing the Cover Installing The Cover 1. Place the computer cover on the chassis. 2. Press down on the computer
ملخص المحتوى في الصفحة رقم 10
Removing the Front Bezel 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Pry the front bezel retention clips away from the chassis. 4. Rotate the bezel away from the computer to release the hooks on the opposite edge of the bezel from the chassis. Related Links Installing The Front Bezel Installing The Front Bezel 1. Insert the hooks along the bottom edge of the front bezel into the slots on the chassis front. 2. Rotate the bezel towards the computer to e
ملخص المحتوى في الصفحة رقم 11
4. Pull the release lever away from the PCIe x16 card to release the securing tab from the dent in the card. Then, ease the card up and out of its connector and remove it from the computer. 5. Lift the PCIe x1 expansion card (if any) up and out of its connector and remove it from the computer. 6. Lift the PCI expansion card (if any) up and out of its connector and remove it from the computer. 7. Lift the PCI x4 expansion card (if any) up and out of its connector and remove it from the computer.
ملخص المحتوى في الصفحة رقم 12
Related Links Installing the Expansion Card Installing The Expansion Card 1. Insert the PCIe x4 card into the connector on the system board and press down to secure it in place. 2. Insert the PCIe card (if any) into the connector on the system board and press down to secure it in place. 3. Insert the PCIe x1 card (if any) into the connector on the system board and press down to secure it in place. 4. Insert the PCIe x16 card (if any) into the connector on the system board and press down to secur
ملخص المحتوى في الصفحة رقم 13
Related Links Installing The Optical Drive Installing The Optical Drive 1. Slide down the optical-drive latch and push the optical drive from the front towards the back of the computer. 2. Connect the data cable and power cable to the optical drive. 3. Install the front bezel. 4. Install the cover. 5. Follow the procedures in After Working Inside Your Computer. Related Links Removing The Optical Drive Removing the Hard Drive 1. Follow the procedures in Before Working Inside Your Computer. 2. Rem
ملخص المحتوى في الصفحة رقم 14
5. Flex the hard-drive bracket and then remove the single 3.5 inch hard drive or two 2.5 inch hard drives from the bracket. 6. Turn over the hard-drive bracket and release the screws that secure the 2.5 inch hard drive to the underside of the bracket. 7. Flex the hard-drive bracket and then remove the two 2.5 inch hard drives from the bracket. 8. Release the screws that secure the 2.5 inch hard drive to the top of the hard-drive bracket. 14
ملخص المحتوى في الصفحة رقم 15
9. Release the screws that secure the 2.5 inch hard drive to the underside of the hard drive bracket. Related Links Installing The Hard Drive Installing The Hard Drive 1. Tighten the screws to secure the 2.5 inch hard drive(s) to the hard-drive bracket. 2. Flex the hard-drive bracket and then insert the single 3.5 inch hard drive or the two 2.5 inch hard drives into the bracket. 3. Press the hard-drive bracket latch towards the hard drive and insert it into the chassis. 4. Connect the data cabl
ملخص المحتوى في الصفحة رقم 16
4. Lift the memory modules out of the connectors on the system board. Related Links Installing The Memory Installing The Memory 1. Insert the memory modules into the connectors on the system board. Install the memory module in the order of A1 > B1 > A2 > B2. 2. Press down on the memory modules until the retention clips spring back to secure them in place. 3. Install the cover. 4. Follow the procedures in After Working Inside Your Computer. Related Links Removing The Memory Removing the Chassis
ملخص المحتوى في الصفحة رقم 17
4. Slide the intrusion switch toward the chassis bottom and remove it from the system board. Related Links Installing The Intrusion Switch Installing The Chassis Intrusion Switch 1. Insert the intrusion switch into the chassis rear and slide it toward the chassis top to secure it. 2. Connect the intrusion-switch cable to the system board. 3. Install the cover. 4. Follow the procedures in After Working Inside Your Computer. Related Links Removing The Intrusion Switch Removing The Speaker 1. Follo
ملخص المحتوى في الصفحة رقم 18
4. Unthread the speaker cable from the chassis clip. 5. Press down the speaker-securing tab and slide the speaker upwards to remove it. Related Links Installing The Internal Speaker Installing The Speaker 1. Press the speaker-securing tab and slide the speaker downward to secure it. 2. Thread the speaker cable into the chassis clip. 3. Connect the speaker cable to the system board. 4. Install the cover. 5. Follow the procedures in After Working Inside Your Computer. Related Links Removing The In
ملخص المحتوى في الصفحة رقم 19
Removing The Heat Sink and Processor NOTE: Your system board may not have a heat sink on the chipset, and may look different from the images described here. 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Disconnect the heat-sink assembly cable from the system board. 4. Loosen the captive screws in the order: 1, 2, 3 and 4. 5. Lift the heat sink assembly upwards, and remove it from the computer. Lay the assembly with the fan facing downwards, and with t
ملخص المحتوى في الصفحة رقم 20
7. Lift the processor cover. 8. Lift the processor to remove it from the socket and place it in an antistatic package. Installing The Heat Sink and Processor 1. Insert the processor into the processor socket. Ensure that the processor is properly seated. 2. Lower the processor cover. 3. Press the release lever down and then move it inward to secure it with the retention hook. 4. Place the heat sink assembly into the chassis. 5. Tighten the captive screws to secure the heat sink assembly to the s
