ملخص المحتوى في الصفحة رقم 1
Installation Above the
Instructions Cooktop Oven
JVM1600 Series
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• Note to Consumer – Keep these instructions
for future reference.
•
IMPORTANT – Save these
• Skill level – Installation of this appliance requires
instructions for local inspector’s use.
basic mechanical and electrical skills.
•
IMPORTANT – Observe all • Proper installation is the responsi
ملخص المحتوى في الصفحة رقم 2
Installation Instructions Recirculating ........................................ 19–22 C CONTENTS Attach Mounting Plate to Wall ............19 General information Preparation of Top Cabinet ................19 Important Safety Instructions .................................. 3 Adapting Blower for Electrical Requirements .......................................... 3 Recirculation ................................20, 21 Hood Exhaust ...................................................... 4, 5 Mount th
ملخص المحتوى في الصفحة رقم 3
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. You should have the wall receptacle and circuit checked The installer must perform a ground continuity check by a qualified electrician to make sure the receptacle is on the power outlet box before beginning the properly grounded. installation to insure that the outlet box is properly Where a standard two-prong wall receptacle is grounded. If not properly grounded, or if the outlet enco
ملخص المحتوى في الصفحة رقم 4
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. x (1) = 24 Ft. 12 Ft. Straight Duct 12 Ft. x (1) = 12 Ft. (6″ Round) Rectangular-to-Round 5 Ft. x (1) = 5
ملخص المحتوى في الصفحة رقم 5
Installation Instructions NOTE: If you need to install ducts, note that the total Maximum duct length: 1 duct length of 3 ⁄4″ x 10″ rectangular or 6″ diameter For satisfactory air movement, the total duct length of round duct should not exceed 120 equivalent feet. 1 3 ⁄4″ x 10″ rectangular or 6″ diameter round duct should Outside ventilation requires a HOOD EXHAUST DUCT. not exceed 120 equivalent feet. Read the following carefully. Elbows, transitions, wall and roof caps, NOTE: It is importa
ملخص المحتوى في الصفحة رقم 6
Installation Instructions PARTS INCLUDED DAMAGE – SHIPMENT/ INSTALLATION ADDITIONAL PARTS • If the unit is damaged in shipment, return the PART QUANTITY unit to the store in which it was bought for repair or replacement. Top Cabinet 1 Template • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must Rear Wall 1 be made by arrangement between customer
ملخص المحتوى في الصفحة رقم 7
Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure and straight edge Pencil Carpenter square # 1 and #2 Phillips screwdriver (optional) Tin snips (for cutting damper, if required) Scissors 3 7 3 Electric drill with ⁄16″, ⁄16″, ⁄8″, (to cut template, if necessary) 1 5 ⁄2″ and ⁄8″ drill bits Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Stud finder or Hammer (opti
ملخص المحتوى في الصفحة رقم 8
Installation Instructions 1 PLACEMENT OF THE MOUNTING PLATE A. REMOVING THE OVEN FROM B. FINDING THE WALL STUDS THE CARTON/REMOVING THE MOUNTING PLATE Remove the turntable, installation instructions, 1 filters, exhaust adaptor, damper, shelf and the small hardware bag. Do not remove the Styrofoam Wall protecting the front of the oven. Studs Fold back all 4 carton flaps fully against carton 2 sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in Cen
ملخص المحتوى في الصفحة رقم 9
At least 30″, up to 36″ Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET C. Plate position – beneath framed recessed Plate position – beneath flat bottom cabinet bottom cabinet Mounting Plate Tabs Mounting Plate Tabs Touching the Cabinet Touching the Back Bottom Frame 30″ to Cooktop Plate position – beneath recessed bottom Your cabinets may have decorative trim that interferes cabinet with front overhang with the oven installation. Remove the decorative trim to i
ملخص المحتوى في الصفحة رقم 10
Installation Instructions D. ALIGNING THE WALL PLATE Hole B Draw a Vertical Line on Wall Hole A from Center of Top Cabinet Hole C Hole D Area E CAUTION: Wear gloves NOTE: Appearance and to avoid cutting fingers on shape of the mounting sharp edges. plate may vary from your model. NOTE: Holes C and D are inside area E. If neither Draw a vertical line on the wall at the center of the 30″ 1 C nor D is in a stud, find a stud somewhere in area E wide space. and draw a fifth circle to line up with t
ملخص المحتوى في الصفحة رقم 11
Installation Instructions 2 INSTALLATION TYPES (Choose A, B or C) This oven is designed for adaptation to the following three NOTE: This oven is shipped assembled for Outside Top types of ventilation: Exhaust (except for non-vented models). Select the type of ventilation required for your installation and proceed A. Outside Top Exhaust (Vertical Duct) to that section. B. Outside Back Exhaust (Horizontal Duct) C.Recirculating (Non-Vented Ductless) OUTSIDE TOP EXHAUST OUTSIDE BACK EXHAUST A B (
ملخص المحتوى في الصفحة رقم 12
Installation Instructions A OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Install Adapter A4. Mount Oven A5. Adjust Exhaust Adaptor A6. Connect Ductwork To use toggle bolts: A1. ATTACH THE MOUNTING Spacing for Toggles PLATE TO THE WALL More Than Wall Thickness Toggle Wings Mounting Toggle Plate Bolt Wall Bolt End Place the mounting plate against the wall and 3 insert the toggle wings into the holes in the wall to Attach
ملخص المحتوى في الصفحة رقم 13
Installation Instructions A4. A2. USE TOP CABINET TEMPLATE MOUNT THE OVEN FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to
ملخص المحتوى في الصفحة رقم 14
Installation Instructions MOUNT THE OVEN (continued) A5. ADJUST THE EXHAUST A4. ADAPTOR Cabinet Front Open the top cabinet and adjust the exhaust adaptor Cabinet Bottom Shelf to connect to the house duct. Filler Block Damper Equivalent to Depth of Cabinet Recess Back of Self-Aligning Screw Oven Oven Top Attach the oven to the top cabinet by inserting 3 3 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Be sure to keep power cord tight. Be careful not
ملخص المحتوى في الصفحة رقم 15
Installation Instructions B OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Attach Exhaust Adaptor to Wall Plate B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Oven B1. PREPARING THE REAR WALL ATTACH THE EXHAUST B2. FOR OUTSIDE BACK EXHAUST ADAPTOR TO THE OVEN REAR You need to cut an opening in the rear wall for PANEL outside exhaust. 1 Unscrew and remove the exhaust adaptor assembly from the top of the oven. Ex
ملخص المحتوى في الصفحة رقم 16
Installation Instructions B4. USE TOP CABINET TEMPLATE B3. ATTACH THE MOUNTING FOR PREPARATION OF TOP PLATE TO THE WALL CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1 Remove the toggle wings from the bolts. 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and r
ملخص المحتوى في الصفحة رقم 17
Installation Instructions 5 Place the blower unit back into the opening. B5. ADAPTING BLOWER FOR OUTSIDE BACK EXHAUST AFTER: Fan Blade Openings 1 Remove the two screws that hold the blower plate Facing Back and remove the screw holding the blower motor to the oven. Slide blower plate from under its retaining flange. Retaining Flange Blower Plate CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match e
ملخص المحتوى في الصفحة رقم 18
Installation Instructions Cabinet Front B6. MOUNT THE OVEN Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE Oven Top INSTALL THIS OVEN. 3 Attach the oven to the top cabinet by inserting IMPORTANT: Do not grip or use handle 3 self-aligning screws through outer top cabinet during installation. holes. Turn two full turns on each screw. Be sure to keep power cord tight. Be careful
ملخص المحتوى في الصفحة رقم 19
Installation Instructions RECIRCULATING (Non-Vented Ductless) C INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter 3 Place the mounting plate against the wall and C1. ATTACH THE MOUNTING insert the toggle wings into the holes in the wall to mount the plate. PLATE TO THE WALL NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet wh
ملخص المحتوى في الصفحة رقم 20
Installation Instructions 4 Roll the blower unit 90° so that fan blade openings C3. ADAPTING BLOWER are facing toward the front of the oven. FOR RECIRCULATION BEFORE: Fan Blade NOTE: The exhaust adaptor with damper is not Openings Facing Up needed for recirculating models. You may want to save them for possible future use. 1 Remove and save screws that hold blower plate and blower unit to the oven. Blower Plate Screws Blower Plate Roll Back of Oven Blower Motor Screw Slide the blower plate from
