ملخص المحتوى في الصفحة رقم 1
TM
HotWire 5030 POTS Splitter Customer Premises
Installation Instructions
Document Number 5030-A2-GN10-10
October 1997
Before You Begin
Verify that:
The local loop POTS service is connected to the POTS/DSL network at the
punchdown block or network interface device (NID).
New or existing unshielded twisted-pair wiring (CAT3 or better) is used with
this product. The CAT3 wiring must meet EIA/TIA-568 specifications with
24 AWG (.5 mm) or 26 AWG (.4 mm).
For RADSL (Rate Adaptive Digital Subscr
ملخص المحتوى في الصفحة رقم 2
What Does the POTS Splitter Do? The POTS splitter and HotWire Remote Termination Unit (RTU) are components in the RADSL Access System. This system provides high-speed Internet or corporate LAN access over traditional twisted-pair copper telephone wiring. The POTS splitter filters out the DSL signal and allows the POTS frequencies to pass through. The RADSL RTU and telephone can function simultaneously over the same pair of copper wires at the customer premises when a POTS splitter is used at bot
ملخص المحتوى في الصفحة رقم 3
Mounting the POTS Splitter Housing The POTS splitter can be placed: On the outside of the structure near the NID or punchdown block, or Inside the building. When mounted outside, the POTS splitter must be installed at or above the height of the NID, and should be a minimum of three feet above ground. At the front of the housing, align the housing to open from the right with the rubber grommet for cable access facing downward. Place the housing upright as shown. Use a Phillips-head or combina
ملخص المحتوى في الصفحة رقم 4
Preparing the POTS Splitter Procedure 1. Unscrew the closure screw and open Lever the housing by pressing on the lever on the right above the closure screw. 2. Remove the rubber grommet at the base of the POTS splitter. 3. Make a small diagonal cut in the rubber grommet to feed the wiring through. 4. Replace the rubber grommet at the base of the POTS splitter. Closure Screw 97-15437-01 Rubber Grommet P1 P2 P3 P4 Base of POTS Splitter 97-15256 4
ملخص المحتوى في الصفحة رقم 5
Installing the POTS Splitter Wiring The local loop ends at the punchdown block or NID. Wiring must be connected from the customer premises (CP) side of the punchdown block or NID to the DSL jack. Typically, the punchdown block is installed in commercial locations and the NID is installed in residential locations. The following is an example of a punchdown block. Punchdown Block Customer Premises Wiring to DSL Jack Demarcation Point Jumper Bridge Clip Wiring to POTS Splitter DSL/POTS ABC D for PO
ملخص المحتوى في الصفحة رقم 6
Telephone Network Interface Device (NID) Customer Premises Demarcation Point Tip T1 (Green) Ring R1 (Red) DSL/POTS Existing POTS From Local Wiring to Loop Ground Telephone 97-15502 3. Disconnect the POTS wiring to the telephone from the T1/R1 connectors on the customer premises side. 4. Feed the disconnected POTS wiring through the POTS splitter rubber grommet access opening created at the base of the POTS splitter. Connect the wiring to the right side labeled PHONE. Attach green to P3 and red t
ملخص المحتوى في الصفحة رقم 7
Reconnecting to the Local Loop Procedure 1. Feed new jumper wiring through the POTS splitter rubber grommet. Remove the insulation at the end of the wiring. 2. On the left side labeled LINE, attach red to terminal screw P1 and green to terminal screw P2. Tighten both terminal screws with a flat-blade screwdriver. POTS Splitter LINE PHONE P1 P2 P3 P4 Red Red Green Green New Wiring from To Punchdown Telephone Block or NID 97-15257-01 7
ملخص المحتوى في الصفحة رقم 8
3. Locate the T1/R1 connectors on the customer premises side of the punchdown block or NID where the existing POTS wiring was removed in Step 3 on page 6. Attach the jumper pair from P1/P2 labeled LINE in the POTS splitter to the T1/R1 connectors. Telephone Network Interface Device (NID) Customer Premises Demarcation Point Tip T1 (Green) Ring R1 (Red) Wiring to DSL Jack DSL/POTS From Local Jumper Wiring to Loop POTS Splitter Ground for POTS 97-15341 4. Snap the lever shut to close the POTS spl
ملخص المحتوى في الصفحة رقم 9
DSL Access Wiring Procedure 1. Attach new wiring to the T1/R1 connectors that will go to the DSL jack from the punchdown block or NID. 2. Tighten the T1/R1 terminal screws with a flat-blade screwdriver. POTS Splitter Customer Premises Punchdown Block or NID DSL Central RJ11 Office Jack POTS/DSL Local Loop Twisted Pair Wiring Demarcation Point 97-15485 You are now ready to run the specified wiring to the RTU location and install a DSL wall jack. To install an RTU, refer to the HotWire 5446 Remo
ملخص المحتوى في الصفحة رقم 10
5030 POTS Splitter Technical Specifications * Item Specification Height x Width x Depth 6.65″ x 5.44″ x 2.25″ (16.89 cm x 13.82 cm x 5.72 cm) Weight 10.2 ounces (289.2 grams) Approvals FCC Part 68 Refer to the equipment’s label for Registration Number. Safety Certifications Refer to the equipment’s label for approvals on product. Physical Environment Operating temperature –40°F to 140°F (–40°C to 60°C) Storage temperature –40°F to 158°F (–40°C to 70°C) Relative humidity 5% to 95% (noncondensing)
ملخص المحتوى في الصفحة رقم 11
Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. This product is intended to be connected to Listed/Certified telephone wiring with a minimum of 24 AWG (.5 mm) behind a Listed/Certified primary protector. 3. Do not attempt to install or service this product yourself, as opening or removing covers may expose you to dangerous high-voltage points or other risks. Refer all installation and servicing to qualified
ملخص المحتوى في الصفحة رقم 12
If the Model 5030 Telephone Line Filter causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that cou
