Crown Boiler BWC300 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

ملخص المحتوى في الصفحة رقم 2

ملخص المحتوى في الصفحة رقم 3

ملخص المحتوى في الصفحة رقم 4

ملخص المحتوى في الصفحة رقم 5

Table 1.1: Summary of PPs Flex Venting Options VENT OPTION # 9 10 PPs FLEX PPs FLEX CLASSIFICATION USED IN THIS MANUAL (MASONRY) (MASONRY) ILLUSTRATED IN FIGURE 1.0 1.0 VENT PIPE PENETRATION THROUGH STRUCTURE CHIMNEY CAP CHIMNEY CAP AIR INTAKE PENETRATION THROUGH STRUCTURE CHIMNEY CAP CHIMNEY CAP 6” DIA 7” DIA MIN CHASE ID (ROUND) 6” x 6” 7” x 7” MIN CHASE ID (RECTANGULAR) 80 mm 100mm NOMINAL PPs FLEX LINER SIZE 80/125 100/150 CONCENTRIC VENT/INTAKE CONNECTOR SIZE BWC070 51ft BWC090 51ft

ملخص المحتوى في الصفحة رقم 6

WARNING Failure to ensure that the chimney is clean, leak tight, water tight, and structurally sound could result in severe corrosion damage to the boiler, damage to the vent system, restriction of combustion air supply, or the entry of flue products into the structure which in turn could cause unreliable operation, property damage, personal injury, or loss of life. 4) Installation of this kit will require an opening at the base of the chimney (at the level of the horizontal vent connection)

ملخص المحتوى في الصفحة رقم 7

ملخص المحتوى في الصفحة رقم 8

ملخص المحتوى في الصفحة رقم 9

ملخص المحتوى في الصفحة رقم 10

ملخص المحتوى في الصفحة رقم 11

ملخص المحتوى في الصفحة رقم 12

6) Remove the rope or pull tool from the end of the vent. 7) Verify that the Male Adaptor is undamaged. Lubricate the brown gasket in the female end of the Elbow with a few drops of water and insert the Male Adaptor fully into the Elbow. 8) Mount the bottom end of the PPs Flex Liner with the Elbow onto the Elbow Support Bracket installed in Step #2 using the Male Adapter Clamp as shown in Figure 1.9. 9) The cap provided with this kit is designed for installation over chimney crowns wit

ملخص المحتوى في الصفحة رقم 13

ملخص المحتوى في الصفحة رقم 14

20) Lubricate the gasket in the female side of the Concentric Adaptor with a few drops of water. Apply a bead of sealant to the Concentric Adaptor flange and secure to the Exterior Wall Plate using the four #6 stainless steel sheet metal screws provided. If the Exterior Wall Plate is omitted as described in Step 17, secure the Concentric Adaptor directly to the exterior wall using four masonry anchors, or other appropriate fasteners, capable of supporting at least 40lbs each. 21) If there i

ملخص المحتوى في الصفحة رقم 15

ملخص المحتوى في الصفحة رقم 16

Manufacturer of Hydronic Heating Products P.O. Box 14818 3633 I. Street Philadelphia, PA 19134 PN: 980079 Rev. 0 07/10 Tel: (215) 535-8900 • Fax: (215) 535-9736 • www.crownboiler.com