ملخص المحتوى في الصفحة رقم 1
This product can be set up
DI-804HV
using any current web browser,
4-Port Broadband
i.e., Internet Explorer 6 or
Netscape Navigator 6.2.3.
VPN Router
Before You Begin
1. If you purchased this router to share your high-speed Internet connection with other
computers, you must have either an Ethernet-based Cable or DSL modem with an
established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for configuring
the DI-804HV
ملخص المحتوى في الصفحة رقم 2
Connecting The DI-804HV VPN Router To Your Network A. First, connect the power adapter to the receptor at the back panel of the DI-804HV and then plug the other end of the power adapter to a wall outlet or power strip. The Power LED will turn ON to indicate proper operation. B. 1. Power off your Cable or DSL modem; some devices may not have a on/ off switch and will require you to unplug the power adapter. Now, the DI-804HV should be powered on and the Cable / DSL modem should be turned off. 2
ملخص المحتوى في الصفحة رقم 3
Restart Your Computer Connecting Additional Computers To The DI-804HV Using additional Ethernet (CAT5 UTP) cables, connect your Ethernet-equipped computers to the remaining Ethernet LAN ports on the back panel of the DI-804HV. WAN LED – a solid light indicates connection on the M1 LED – will flash COM LED – a solid WAN port. This consistently to indicate light indicates a proper LED blinks during that the DI-804HV is connection to a dial-up data transmission. working properly. modem. LOCAL NETW
ملخص المحتوى في الصفحة رقم 4
When you have completed the steps in this Quick Installation Guide, your connected network should look similar to this: Using The Setup Wizard Open your Web browser and type “http://192.168.0.1” into the URL address box. Then press the Enter or Return key. The logon pop-up screen will appear. Type “admin” for the username and leave the password field blank. Click OK 4
ملخص المحتوى في الصفحة رقم 5
The Setup Wizard (continued) Once you have logged in, the Home screen will appear. Click Run Wizard You will see the following screens Click Next Set up your new password. You have the option to establish a password. Click Next 5
ملخص المحتوى في الصفحة رقم 6
The Setup Wizard (continued) Choose your time zone from the drop down list. Click Next Select your Internet Connection. You will be prompted to select the type of Internet connection for your router. If you are unsure of which setting to select, please contact your Internet Service Provider. Click Next Select Others only if you use PPTP in Europe or Big Pond Cable in Australia. 6
ملخص المحتوى في الصفحة رقم 7
The Setup Wizard (continued) If you selected Dynamic IP Address, this screen will appear: (Used mainly for Cable Internet service.) Click the “Clone MAC Address” button to automatically copy the MAC address of the network adapter in your computer. You can also manually type in the MAC address. What is a MAC address? Each network adapter has a discrete Media Access Control (MAC) address. Note that some computers and peripherals may already include built-in network adapters. Click Next If your ISP
ملخص المحتوى في الصفحة رقم 8
The Setup Wizard (continued) If your ISP uses PPPoE (Point-to-Point Protocol over Ethernet), and this option is selected, then this screen will appear: (Used mainly for DSL Internet service.) Please be sure to remove any existing PPPoE client software installed on your computers. Enter in the username and password provided to you by your ISP. Click Next Configure this section only if you have an analog dial-up account. Otherwise click Next to skip. Click Next 8
ملخص المحتوى في الصفحة رقم 9
Your Setup is Complete! Click Restart Test Internet Connection. You will be returned to the Home tab. Click to Exit Then relaunch your Web browser (i.e., Internet Explorer or Netscape Navigator), to link to your favorite Web site to test your Internet connection. For additional settings or information, refer to the Advanced, Tools, or Status tabs on the web-management interface; or to the Manual located on the CD. 9
ملخص المحتوى في الصفحة رقم 10
APPENDIX (continued) To connect to the network, make sure the network adapter in your computer is configured properly. Here’s how to configure the network adapter to obtain an IP address automatically for the DI-804HV Broadband Router. For Microsoft Windows XP: Go to Start > right click on My Network Places > select Properties > Double-click on the Network Connection associated with the Ethernet adapter (i.e., D-Link DFE-530TX+). Click Internet Protocol (TCP/IP) Click Properties Select Obtain an
ملخص المحتوى في الصفحة رقم 11
For Apple Macintosh OS X: Go to the Apple Menu Click on Network and Select Click on System Preferences Network Select Built-in Ethernet in the show pull down menu Select Using DHCP in the Configure pull down menu Click on Apply Now The IP address information, the Subnet Mask, the Router’s IP address and the Ethernet adapter address will appear 11
ملخص المحتوى في الصفحة رقم 12
Technical Support You can find the most recent software and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States for the duration of the warranty period on this product. U.S. customers can contact D-Link technical support through our website or by phone. D-Link Technical Support over the Telephone: (877) 453-5465 24 hours a day, seven days a week D-Link Technical Support over the Internet: http://support.dlink.com 12
