ملخص المحتوى في الصفحة رقم 1
CHAPTER 3
Getting Started
This chapter describes the typical tasks you should complete to start using the Cisco 12000/10720
Router Manager application. See Figure 3-1 on page 3-2 for further details.
This chapter provides the following information:
• Cisco 12000/10720 Router Manager Workflow
� Starting Cisco EMF and Cisco 12000/10720 Router Manager
� Deployment
Cisco 12000/10720 Router Manager Workflow
Figure 3-1 outlines the steps involved in installing, configuring and using the Cisco 1200
ملخص المحتوى في الصفحة رقم 2
Chapter 3 Getting Started Cisco 12000/10720 Router Manager Workflow Figure 3-1 Workflow for Cisco 12000/10720 Router Manager Install Cisco EMF software Install C12000/10720M software Start CEMF Start a Cisco EMF session Deploy objects Enter username and password Perform Subchassis discovery Review deployment Layer 3 QoS and check for alarms Chassis Module Interface ATM Management Management Management Connections Fault VLAN Management Sub-interface Change Management Cisco 12000/10700 v3.
ملخص المحتوى في الصفحة رقم 3
Chapter 3 Getting Started Starting Cisco EMF and Cisco 12000/10720 Router Manager Starting Cisco EMF and Cisco 12000/10720 Router Manager The Cisco 12000/10720 Router Manager application is viewed through the Cisco Element Management Framework (Cisco EMF). It is important to understand how Cisco EMF works before you use the Cisco 12000/10720 Router Manager application (refer to the Cisco Element Management Framework User Guide for further details). Cisco 12000/10720 Router Manager aut
ملخص المحتوى في الصفحة رقم 4
Chapter 3 Getting Started Starting Cisco EMF and Cisco 12000/10720 Router Manager The Login window (see Figure 3-2) appears. Figure 3-2 Login Window Step 2 Enter a valid user name and password. Step 3 Click Ok to proceed. When an unknown user name or password is entered, an error is displayed. Click Ok, then enter a valid user name and password. Note You have three attempts to enter a valid user name and password.After the third failed attempt the session does not start and the Login
ملخص المحتوى في الصفحة رقم 5
Chapter 3 Getting Started Starting Cisco EMF and Cisco 12000/10720 Router Manager Launchpad The icons displayed in the CEMF Manager and Event Manager panels on the Launchpad represent the applications provided by this Cisco EMF installation. Extra icons may appear when additional packages are installed. The icons (see Figure 3-3) represent the standard Cisco EMF tools. Figure 3-3 Launchpad Viewer icon - Launches MapViewer Groups icon - Launches the Object Group Manager Access icon - La
ملخص المحتوى في الصفحة رقم 6
Chapter 3 Getting Started Starting Cisco EMF and Cisco 12000/10720 Router Manager Map Viewer (Viewer) MapViewer allows complete flexibility in viewing, building, and monitoring your network using graphical representations of network elements. MapViewer is the primary entry point into the Cisco 12000/10720 Router Manager. When the MapViewer application is launched, a window appears corresponding to the highlighted map icon in the hierarchy pane. You can easily monitor the status of all
ملخص المحتوى في الصفحة رقم 7
Chapter 3 Getting Started Starting Cisco EMF and Cisco 12000/10720 Router Manager Notification Profiles An important aspect of a monitoring system which captures and reacts to events on the network is when and how a network operator is informed of these events. The Event Manager uses notifications for this. For example, when the temperature of a line card rises 10 degrees above normal an e-mail might be sent to the network operator warning of a potential problem and a minor event migh
ملخص المحتوى في الصفحة رقم 8
Chapter 3 Getting Started Deployment PreFilter Event pre-filtering allows any event generated by the network which matches the criteria established in the filter to be “filtered out”, and thus not saved into the database. Pre-filtering offers you the capability to eliminate unwanted or undesired events from entering the management system altogether. Pre-filtering is managed through the PreFilter application or from the Event Browser. The PreFilter application is launched via the PreFi
ملخص المحتوى في الصفحة رقم 9
Chapter 3 Getting Started Deployment You can also deploy either of the following logical objects: � SVC—See “Deploying an SVC Object” section on page 12-22 � PVC—See “Deploying a PVC Object” section on page 12-18 � VLAN Domain, VLAN and VLAN sub-interface—See “Deploying VLAN objects” section on page 13-4 Tip WRED (Weighted Random Early Detection) and CAR (Committed Access Rate) objects are not created using the deployment wizard. For details on creating these objects manually, see Cha
ملخص المحتوى في الصفحة رقم 10
Chapter 3 Getting Started Deployment Figure 3-4 Deployment Process Workflow IP Auto-discovery of Cisco 12000/10720 series chassis Stage 1: Manually Stage 2: Chassis OR deploy a generic object level deployment Manual deployment of the Cisco 12000/10720 series chassis Stage 3: Sub-chassis level deployment Sub-chassis Discovery Optional AND/OR Manually deploy Sub-chassis objects 1. The first deployment stage is to manually deploy a Generic (Site) object. A Site object can be looked upon as
ملخص المحتوى في الصفحة رقم 11
Chapter 3 Getting Started Deployment Table 3-1 Generic Object Deployment Templates Object to be Deployed Deployment Templates Available Generic Bay IP Device Region SNMP Agent SNMP MIB-2 Agent SNMP Proxied Device Site This section provided an example that shows how to deploy a Site object. The deployment process differs slightly for other types of generic object. To deploy a Generic (Site) object, proceed as follows: Step 1 Place the cursor over a relevant object to determine the object
ملخص المحتوى في الصفحة رقم 12
Chapter 3 Getting Started Deployment Figure 3-6 Deployment Wizard - Templates Window Step 4 Select the generic object that you wish to deploy from the list supplied. In this example (shown in Figure 3-6) shows the deployment profile for a Site object is selected. The Deployment Wizard steps through a series of windows that prompt you for the information required to deploy the Site object. Step 5 Click Forward. Cisco 12000/10700 v3.1.1 Router Manager User Guide 3-12 OL-4455-01
ملخص المحتوى في الصفحة رقم 13
Chapter 3 Getting Started Deployment The Deployment Wizard - Object Parameters window appears (see Figure 3-7). Figure 3-7 Deployment Wizard - Object Parameters Window (1 of 2) Step 6 Enter the number of Sites required. A single site was entered in this example. Step 7 Click Forward. Cisco 12000/10700 v3.1.1 Router Manager User Guide OL-4455-01 3-13
ملخص المحتوى في الصفحة رقم 14
Chapter 3 Getting Started Deployment Figure 3-8 Deployment Wizard - Object Parameters Window (2 of 2) Step 8 Enter a Site name. Each Site must have a unique name. In this example the site is called Site-srp. Step 9 Click Forward. Cisco 12000/10700 v3.1.1 Router Manager User Guide 3-14 OL-4455-01
ملخص المحتوى في الصفحة رقم 15
Chapter 3 Getting Started Deployment The Deployment Wizard - Views window appears. Figure 3-9 Deployment Wizard—Views Window Step 10 Click Select, to select a physical view. Cisco 12000/10700 v3.1.1 Router Manager User Guide OL-4455-01 3-15
ملخص المحتوى في الصفحة رقم 16
Chapter 3 Getting Started Deployment The Object Selector Window appears. Figure 3-10 Object Selector Step 11 Select the object where you wish to place the Site object. Step 12 Click Apply. The Deployment Wizard - Views window re-appears with the selection displayed. Cisco 12000/10700 v3.1.1 Router Manager User Guide 3-16 OL-4455-01
ملخص المحتوى في الصفحة رقم 17
Chapter 3 Getting Started Deployment Figure 3-11 Deployment Wizard—Views Window Step 13 Click Forward. Note You are prompted to repeat Steps 8 to 13 if you are deploying more than one Site. The Deployment - Wizard Summary window appears. The Summary window provides details of the object you are about to deploy. Cisco 12000/10700 v3.1.1 Router Manager User Guide OL-4455-01 3-17
ملخص المحتوى في الصفحة رقم 18
Chapter 3 Getting Started Deployment Figure 3-12 Deployment Wizard—Summary Window Step 14 Click Finish (when the Deployment Summary information is correct) to complete deployment and close the Deployment Wizard - Summary window. The new Site object (that is, Site-srp) is created and displayed in the Map Viewer window. Figure 3-13 Example Showing the Newly Deployed Site-srp Object Cisco 12000/10700 v3.1.1 Router Manager User Guide 3-18 OL-4455-01
ملخص المحتوى في الصفحة رقم 19
Chapter 3 Getting Started Deployment Note This deployment procedure can be applied to the deployment of any of the generic objects although all of the steps may not apply to the particular generic object that you are deploying. IP Auto Discovery of the Cisco Chassis Auto discovery is the application that discovers existing Cisco 12000/10720 Routers, saving time and effort. The auto discovery window can be opened from the Viewer or Discovery icon in the Launchpad. For further informat
ملخص المحتوى في الصفحة رقم 20
Chapter 3 Getting Started Deployment Figure 3-14 Example of Auto Discovery Manually Deploying a Cisco 12000/10720 Chassis Tip It is recommended that you ping the Cisco 12000/10720 Router you intend to deploy to ensure the device can be contacted. To deploy a chassis, proceed as follows: Step 1 In the Map Viewer, right click on the site object under which you wish to deploy the chassis, then choose Deployment>Cisco 12000/10720 Manager>12008 or 12012 or 12016 or 12404 or 12406 or 12410 o
