ملخص المحتوى في الصفحة رقم 1
ATTO Technology, Inc.
Ô Ô
ATTO FibreBridge
Installation & Operations
Manual
FibreBridge 2100R, 2200R/D and 3200R
© 2000 ATTO Technology, Incorporated. All rights reserved. All brand or product names are trademarks of their respective holders.
No part of this manual may be reproduced in any form or by any means without the express written permission of ATTO
Technology, Incorporated.
Rev. D 1/01 Document Control Nu mber: PRMA-0220-000
ملخص المحتوى في الصفحة رقم 2
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual ATTO Technology, Inc. - i -
ملخص المحتوى في الصفحة رقم 3
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual CHAPTER 1: INTRODUCTION..............................................................................................................................................1 FIBREBRIDGE PRODUCT MODULE DESCRIPTION....................................................................................................................1 FC RACK SYSTEM PRODUCT DESCRIPTION .......................................................................
ملخص المحتوى في الصفحة رقم 4
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual SCSI TERMINATION .................................................................................................................................................................. 21 FIBRE CHANNEL CABLING........................................................................................................................................................ 22 GBICS................................................................
ملخص المحتوى في الصفحة رقم 5
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual APPENDIX B: RADIO AND TELEVISION INTERFERENCE...................................................................................46 APPENDIX C: CIRCUIT BOARD DIMENSIONS & IMPORTANT JUMPER LOCATIONS..........................48 APPENDIX D: FIBRE CHANNEL RESOURCES...........................................................................................................51 APPENDIX E: FIBRE CHANNEL ACCESSORIES .....................
ملخص المحتوى في الصفحة رقم 6
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual Chapter 1: INTRODUCTION This manual will provide an overview of the various ATTO FibreBridge products and product modules as well as describe how to install and configure the bridge for optimal operation. The following products will be discussed: • FibreBridge 2100R – Rackmount bridge module • FibreBridge 3200R – Rackmount bridge module • FibreBridge 2200R/D – Rackmount or Desktop bridge • FC Rack System – Rack enclosure to
ملخص المحتوى في الصفحة رقم 7
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual Fibre Channel Technology Fibre Channel is a serial communications interface designed for the transfer of large amounts of data between a variety of hardware systems over long distances. It is becoming a key technology for applications that require shared, high bandwidth access to storage. Fibre Channel provides a logical point-to point serial channel for the transfer of data between a buffer at a source device and a buffer a
ملخص المحتوى في الصفحة رقم 8
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual ™ Chapter 2: ATTO FibreBridge Benefits and Features The different ATTO FibreBridge Product Modules come with a variety of features in an effort to offer users a choice of cost-effective as well as high end solutions for including native SCSI devices into a Fibre Channel Storage Area Network (SAN). Below is a list of some of the key features available, followed by a table identifying which features are offered in the differe
ملخص المحتوى في الصفحة رقم 9
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual can support F_Ports or FL_Ports and automatically configure itself. ATTO Technology recommends that this mode of operation not be used. It is better to force the port to the desired mode. When connecting the bridge to a F_Port device, set the port connection mode to “Point-to-Point.” When connecting to a FL_Port device, set the port connection mode to “Loop”. The port connection mode of the bridge can be set using the RS-
ملخص المحتوى في الصفحة رقم 10
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual Chapter 3: ATTO FC Rack Enclosure and Power Modules This chapter provides an overview of the ATTO FC Rack System and the Power Modules, as well the installation process for the Power Modules. The main enclosure of the ATTO FC Rack System houses all ™ the FibreBridge Product Modules and Power Modules. There are two bays for FibreBridge Product Modules and two bays for Power Modules. Physical Dimensions Figure 3.1 Rear view w
ملخص المحتوى في الصفحة رقم 11
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual Figure 3.3 Side view with hole dimensions in inches (mm in parentheses) Environmental The ATTO FC Rack System is designed to operate in an environment that is 0°-40° C, 0-90% humidity and non-condensing. Cooling Airflow Each Power Module provides a total of 16 CFM of airflow. A system that has two Power Modules installed will have a total of 32 CFM of airflow. Air enters through the sides of the enclosure and is exhausted out
ملخص المحتوى في الصفحة رقم 12
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual Internal Power Distribution The ATTO FC Rack System provides a redundant power scheme with two "hot swappable" Power Supply Modules. Each Power Supply Module feeds 12V to the backplane. From there, the power is distributed to the bridge modules and the fans. A failure of one power supply will not affect the functionality of the bridge modules or the cooling system since the second supply is still supplying power to the backp
ملخص المحتوى في الصفحة رقم 13
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual • Power Draw: The maximum power draw is 2 Amps @ 110 Volts for the entire ATTO FC Rack System. When the ATTO FC Rack System has two Power Modules, the entire unit will still draw only 2 Amps @ 110 Volts. LED Indicator The green LED indicator on the Power Module will light when the module is correctly installed and the switch is turned on. This LED indicates that power is being drawn from this module and is available on the b
ملخص المحتوى في الصفحة رقم 14
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual Step 5. Turn the power switch on the power module to the on position. Verify that the green LED is illuminated. The correct method for removal of a power module is as follows: Step 1. The power switch on the rear of the power module must be in the off position. Make sure the power LED is NOT illuminated. Step 2. Disconnect the power cord from the power module as well as the AC power source. Step 3. Loosen the two thumb
ملخص المحتوى في الصفحة رقم 15
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual ™ Chapter 4: ATTO FibreBridge Product Module Integration This chapter provides an overview of the ATTO FibreBridge Product Modules and their installation process. ATTO FibreBridge module is designed to slide into and mount to either of the two module bays on the main FC Rack Enclosure chassis. The bridge module must be inserted into the face of the rack chassis where the cooling grids are located. The connector on the back
ملخص المحتوى في الصفحة رقم 16
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual Figure 4.2 ATTO FibreBridge Power Connector Figure 4.3 ATTO FibreBridge 2100R Product Module Figure 4.4 ATTO FibreBridge 3200R Product Module ATTO Technology, Inc. - 11 -
ملخص المحتوى في الصفحة رقم 17
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual Fibre Channel Ports The Fibre Channel ports on the bridge modules are used to connect the bridge into either a Fabric or Arbitrated Loop. Some of the features for the Fibre Channel ports include: • 1.0625 Gigahertz (100 MB/sec) • Support for Class 2, Class 3, and Intermix ANSI Fibre Channel specifications • Support PLDA, Public Loop Login (NL_Ports) as well as Fabric Direct Connect (N_Port) • Support for Full Duplex transmis
ملخص المحتوى في الصفحة رقم 18
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual • Single Ended Ultra SCSI – 40 MB/sec max per bus • High Voltage Differential (HVD) Ultra SCSI – 40 MB/sec max per bus Each of the two ports is totally independent from the other. This means that each bus is capable of 15 devices and each bus is capable of 40/80 MB/sec (Ultra/Ultra2). There are a few advantages to this. First, you are able to use software striping to create a RAID 0 group that includes devices from both SCS
ملخص المحتوى في الصفحة رقم 19
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual FC Activity – This LED blinks to show activity occurring on the Fibre Channel port of the unit. The LED may appear to be steadily lit during times of very high activity. SCSI 1 Activity, SCSI 2 Activity – One LED for each SCSI bus displays activity on that SCSI bus. Ready – A few seconds after power has been applied, the Ready LED should be illuminated. This indicates that the FibreBridge has passed its power on self-test and
ملخص المحتوى في الصفحة رقم 20
ATTO Technology, Inc. ATTO FibreBridge Installation & Operation Manual ™ Chapter 5: FibreBridge 2200R/D This chapter provides an overview of the ATTO FibreBridge 2200R/D. The FibreBridge 2200R/D is a Fibre Channel to SCSI bridge for high throughput enterprise environments that is designed for cost sensitive implementations. The 2200R/D contains all of the high end connectivity, monitoring, and management features as the FibreBridge 3200 module, but without the dual redundant power supply and c
