Transition Networks SSETF10XX-200 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

SSETF10xx-200
Product Features
Full-Duplex / Half-Duplex
USER’S GUIDE The SSETF10xx-200 receives and transmits network signals in either full-
duplex or half-duplex mode (depending upon the network devices to which
SSETF10xx-200
the Media Converter is attached).
Stand-Alone Media Converter
Fast Ethernet™ in full-duplex mode allows the maximum cable distances
• Ethernet™ and Fast Ethernet™
listed on page 1.
 10Base-T / 100Base-TX to
Fast Ethernet™ in half-duplex mode requires attention to the

ملخص المحتوى في الصفحة رقم 2

SSETF10xx-200 INSTALLATION INSTALLATION -- Continued Installing the Cable Power the Media Converter 1. Install the power adapter cord to the back of the Media Converter. FIBER 2. Connect the power adapter plug to AC power. 1. Locate or build 10Base-FL or 100Base-SX compliant fiber cable with male, two-stranded TX to RX connectors installed at both ends. 3. Verify that the Media Converter is powered by observing the illuminated LED power indicator light. 2. Connect the fiber cables to SSETF10xx-

ملخص المحتوى في الصفحة رقم 3

SSETF10xx-200 CABLE SPECIFICATIONS TECHNICAL SPECIFICATIONS The physical characteristics must meet or exceed IEEE 802.3™ specifications. Standards: IEEE 802.3™ Data Rate: 10 Mb/s, 100 Mb/s Fiber Cable Dimensions: 3.4" x 0.86" x 5.0" (86 mm x 22 mm x 127 mm) -9 Bit Error Rate: <10 Multimode fiber (recommended): 62.5/125 µm Weight: 8 oz (227 g) (approximate) Multimode fiber (optional): 100/140, 85/140, 50/125 µm Power Supply DC Output: 12VDC, 500 mA (minimum) Wavelength: 850 nm mulitmode mini

ملخص المحتوى في الصفحة رقم 4

SSETF10xx-200 HALF-DUPLEX NETWORK FAULT ISOLATION and CORRECTION If the Media Converter fails, isolate and correct the fault by determining the 512-Bit Rule answers to the following questions and then taking the indicated action: In a half-duplex network, the maximum cable lengths are determined by the round trip delay limitations of each Fast Ethernet™ collision domain. (A 1. Is the P(o)W(e)R LED on the Media Converter illuminated? collision domain is the longest path between any two terminal d

ملخص المحتوى في الصفحة رقم 5

SSETF10xx-200 5. Is the RXC LED flashing? CONTACT US NO  If there is no activity on the 10Base-T/100Base-TX port, proceed to Technical Support step 6. Technical support is avialable 7:00 AM - 6:00 PM CST (GMT -6:00)  If there is activity on the 10Base-T/100Base-TX port, disconnect and US and Canada: 1-800-260-1312 reconnect the 10Base-T/100Base-TX cable to restart the initialization International: 00-1-952-941-7600 process.  Restart the workstation to restart the initialization process. Trans

ملخص المحتوى في الصفحة رقم 6

SSETF10xx-200 COMPLIANCE INFORMATION UL Listed C-UL Listed (Canada) CISPR22/EN55022 Class A & B + EN55024 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A & B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if n