ملخص المحتوى في الصفحة رقم 1
TL-PA250
AV200+ Powerline Adapter with AC Pass Through
Rev: 1.0.0
1910010540
ملخص المحتوى في الصفحة رقم 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2011 TP-LINK TECHNOLOGIES CO.,
ملخص المحتوى في الصفحة رقم 3
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarante
ملخص المحتوى في الصفحة رقم 4
Important Safety Instructions 1. Do not open this product or attempt to service it; it may expose you to dangerous high voltage or other risks. 2. Do not operate this product near water. 3. Do not place or operate this product near a radiator or a heat register. 4. Do not expose this product to dampness, dust or corrosive liquids. 5. Do not connect this product or disconnect it from a wall socket during a lightning or a thunderstorm 6. Do not block the ventilation slots of this product,
ملخص المحتوى في الصفحة رقم 5
CONTENTS Chapter 1 Introduction ..................................................................................................... 1 1.1 LED Indicator ................................................................................................................ 2 1.2 Physical Interface ......................................................................................................... 3 Chapter 2 Connecting Mechanism ...............................................................
ملخص المحتوى في الصفحة رقم 6
TL-PA250 AV200+ Powerline Adapter with AC Pass Through Chapter 1 Introduction Congratulations on your purchase of this outstanding Powerline Adapter. This device is an AV200+ Powerline Adapter with AC Pass Through which transforms your house’s existing electrical wiring into a ubiquitous networking infrastructure. Simply plug thisAV200+ Powerline Adapter with AC Pass Through into an ordinary AC power outlet which will easily extend your Cable/xDSL broadband connection or existing Ethern
ملخص المحتوى في الصفحة رقم 7
TL-PA250 AV200+ Powerline Adapter with AC Pass Through 1.1 LED Indicator The LED indicator displays information about the device’s status. Item Status Indication Solid The adapter is on. Blinking The adapter is in power-saving mode. Power LED Off The adapter is off. Solid The adapter is connecting to a Powerline network. Blinking The adapter is sending or receiving data. Powerline LED The adapter has not connected to Powerline network or Off is in power-saving mode. The Ether
ملخص المحتوى في الصفحة رقم 8
TL-PA250 AV200+ Powerline Adapter with AC Pass Through 1.2 Physical Interface There are four physical interfaces on this Mini Powerline Adapter. Integrated Electrical Socket Power Plug Ethernet Port Pair Button Interface Description It is a 10/100Mbps Ethernet port on the AV adapter for connecting it Ethernet Port to the PC or the broadband device with the network cable. Power Plug* A Power Plug connected to any 100V ~ 240V AC power socket After you plug in your new AV ada
ملخص المحتوى في الصفحة رقم 9
TL-PA250 AV200+ Powerline Adapter with AC Pass Through Chapter 2 Connecting Mechanism 2.1 Introduction The Powerline Adapter supports up to 200Mbps data rate. With this high speed connection rate, this Powerline Adapter allows you to setup a high speed home network by using your home existing electrical wiring. Simply plug this Powerline Adapter into an ordinary power outlet to extend your Cable/xDSL broadband connection or existing LAN network to any other electrical outlet in any room
ملخص المحتوى في الصفحة رقم 10
TL-PA250 AV200+ Powerline Adapter with AC Pass Through 2.3 Hardware Connection – Computer For those computers you wish to be networked by Powerline Adapter, each of the computers must be properly connected with a Powerline Adapter through an Ethernet (RJ-45) cable. Following are the steps to properly connect the Powerline Adapter to your computer: 1 ． Connect one end of the provided Ethernet (RJ-45) cable to the Powerline Adapter’s Ethernet port. 2 ． Connect the other end of the Ethernet
ملخص المحتوى في الصفحة رقم 11
TL-PA250 AV200+ Powerline Adapter with AC Pass Through Note: Where the MAINS plug or an appliance coupler is used as the disconnected device, the disconnect device shall remain readily operable. The idle wall sockets or electrical outlets in your household electrical circuit can be used normally without interference from the network. 6
ملخص المحتوى في الصفحة رقم 12
TL-PA250 AV200+ Powerline Adapter with AC Pass Through Chapter 3 Installing Management Utility Please verify that no other Powerline Adapter or any Encryption Management Utilities are installed before installing the provided software. If other Powerline Utilities are installed, uninstall them and restart your personal computer before installing this provided software. Note: Please make sure that you have installed the WinPcap (the version of which should be beyond 4.1.1 inclusive) o
ملخص المحتوى في الصفحة رقم 13
TL-PA250 AV200+ Powerline Adapter with AC Pass Through 8
ملخص المحتوى في الصفحة رقم 14
TL-PA250 AV200+ Powerline Adapter with AC Pass Through 9
ملخص المحتوى في الصفحة رقم 15
TL-PA250 AV200+ Powerline Adapter with AC Pass Through Step 3: After the installation, a shortcut to the “TL-PA250 Powerline Utility” application icon is provided on the windows desktop. 10
ملخص المحتوى في الصفحة رقم 16
TL-PA250 AV200+ Powerline Adapter with AC Pass Through Chapter 4 Using the Management Utility After you’d successfully installed the Powerline Adapter hardware and Management Utility software, you can set up or configure the devices according to your need. This Powerline Adapter Configuration Utility enables the users to identify powerline devices on the powerline network, measure data rate performance, ensure privacy and perform diagnostics by setting user-defined secure powerline net
ملخص المحتوى في الصفحة رقم 17
TL-PA250 AV200+ Powerline Adapter with AC Pass Through Local Device(s) on your computer: This shows all local Powerline Ethernet Adapter found connected to the computer’s LAN card. In most cases, only one device will display in this panel. Click and select the local device shown on the screen then click “Connect” tab to manage the Powerline Ethernet Adapter. The status message shown above the “Connect” button indicates that your PC is connected to the same device. Once the chosen Power
ملخص المحتوى في الصفحة رقم 18
TL-PA250 AV200+ Powerline Adapter with AC Pass Through Note: The parameter information of PIB will restore to the factory defaults after resetting the Powerline Adapter. To upgrade the device's firmware, follow these instructions: 1. Download PIB file and firmware upgrade file from TP-LINK website (http://www.tp-link.com). 2. Enter the path name or click Browse… to select the downloaded files on the computer into the corresponding blanks. 3. Click the OK button. Note: Do not turn
ملخص المحتوى في الصفحة رقم 19
TL-PA250 AV200+ Powerline Adapter with AC Pass Through 4.1.2 Enter Password Enter the password of the remote Powerline Adapters, and then you can set the network name of these devices on Privacy configuration homepage. The password can be found on the back of the device. Select the Powerline Adapter from the list, click the Enter Password button and then the following screen will display. Enter your Password (Take note of the password format) and click “OK” after setup. 14
ملخص المحتوى في الصفحة رقم 20
TL-PA250 AV200+ Powerline Adapter with AC Pass Through Note: The Powerline Adapter device must be present on the power line (plugged in) in order for the password to be confirmed and added to the network. If the Powerline Adapter device could not be located, a warning message will be shown. 4.1.3 Add Device The following dialog box will pop up when clicking the “Add” button under the Main configuration homepage. The dialog box allows you to enter both the selected device’s name and pa
