ملخص المحتوى في الصفحة رقم 1
SIMATIC
PC Adapter
TS Adapter
Quick Reference Guide
Edition 01/2003
A5E00078070-02
ملخص المحتوى في الصفحة رقم 2
Exclusion of Liability
!
"
ملخص المحتوى في الصفحة رقم 3
Contents 1 Product Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3Accessories 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 MPI/DP Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5 Prerequisites for Operation . . . . . . . . . . . . . . . . . . . . . . . 5 5.1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 4
PC/MPI Cable Kurzanleitung PC/TS Adapter A5E00078070-02 ii
ملخص المحتوى في الصفحة رقم 5
Quick Reference Guide PC/TS Adapter 1 Product Definition The adapter is available as: PC adapter 6ES7 972-0CA2x-0XA0 or TS adapter 6ES7 972-0CA3x-0XA0 Note Where ’adapter’ is referred to below, the text applies to both variants. The PC adapter connects a PC to the MPI/DP interface (Multipoint Interface) via the serial COM port of an S7/M7/C7 system. This does not require a PC slot, that is, the adapter is also suitable for use in non-expandable PCs such as notebooks. 1) 19.2/38.4 kbps PC ada
ملخص المحتوى في الصفحة رقم 6
PC/TS Adapter Quick Reference Guide With ’direct connection’, the TS adapter allows you to link programming devices/PCs with S7/M7/C7 systems. With this setup, the TS adapter corresponds in functionality to the PC adapter. With ’modem connection’, the TS adapter enables you to link programming devices/PCs with S7/M7/C7 systems over the telephone network. 19.2/38.4 kb RS232 TS adapter Direct Connection 1) S7/M7/C7 system PC RS232 Switch MPI/DP COM1... 19.2/38.4 kbps Modem Connection RS232 TS adap
ملخص المحتوى في الصفحة رقم 7
Quick Reference Guide PC/TS Adapter Adapter MPI/DP connector LED “POWER” LED “ACTIVE” Switch RS232 connector “19.2/38.4 kbps” Figure 1-3 Adapter The two adapter types differ with respect to the location of the MPI/DP parameters: The MPI/DP parameters for the PC adapter are set in “Set PG/PC interface”. When opening an online display for the first time, ther parameters are transferred to the PC adapter. The MPI/DP parameters for the TS adapter are set via a Teleservice application and stored
ملخص المحتوى في الصفحة رقم 8
PC/TS Adapter Quick Reference Guide 2 Package Components Adapter Quick Reference Guide Mounting assembly (TS adapter only) 3 Accessories (not part of the adapter package) RS232 cable, 6 meters in length 6ES7 901-1BF00-0XA0 (required to operate the PC adapter and to operate the TS adapter in direct connection only). 4 MPI/DP Network A maximum of 32 nodes can be interfaced to an MPI/DP network segment. The total cable length may not exceed 50 meters. Using so-called RS485 repeaters, sever
ملخص المحتوى في الصفحة رقم 9
Quick Reference Guide PC/TS Adapter 5 Prerequisites for Operation 5.1 Hardware PC/programming device with a free COM port (COM1 or COM2, 9-pin COM connection). Appropriate adapters for other connector combinations are available in specialist shops, for example 9-pin to 25-pin subminiature D connector. 25-pin subminiature D: 9-pin subminiature D: Signal: Shield Shield DCD 8 1 RXD 3 2 TXD 2 3 DTR 20 4 GND 7 5 DSR 6 6 RTS 4 7 CTS 5 8 RI 22 9 Shield Shield 1) 1) Connector casing Connector casing 1)
ملخص المحتوى في الصفحة رقم 10
PC/TS Adapter Quick Reference Guide 6 Connecting the Adapter 6.1 Safety-related Guidelines Qualified Personnel A device/system may only be commissioned or operated by qualified personnel. Qualified personnel as referred to in safety guidelines in this document are persons authorized to energize, de-energize, clear, ground, and tag circuits, equipment and systems in accordance with established safety practice. For a detailed description of the safety-related guidelines, please refer to the Append
ملخص المحتوى في الصفحة رقم 11
Quick Reference Guide PC/TS Adapter 6.2 General Remarks MPI/DP side: Adapter and S7/M7/C7 system each represent one network node. In networks comprising two nodes (adapter and S7/M7/C7 system), the adapter is plugged directly into the S7/M7/C7 system’s MPI/DP port; in networks consisting of more than two nodes, the adapter is plugged into a Profibus connector’s “PG port” (SINEC L2 bus connector); for details, please refer to catalog IK10. S7 Figure 1-5 Connecting to an S7 System (Two Network N
ملخص المحتوى في الصفحة رقم 12
PC/TS Adapter Quick Reference Guide As the adapter receives its power supply via the MPI/DP in- terface, only those interfaces can be used which provide 24 V DC and 5 V DC with the voltages and currents specified in the table in the ”Technical Specifications” (Chapter 7). The- refore a connection at the free end of a PROFIBUS cable is not possible. 9-pin subminiature D: Adapter 9-pin subminiature D: 50mA (typ) 1 DCD P24V 7 RS232 +5V 2 RXD M24V 2 3 TXD 40mA (typ) P5V 6 DTR 4 M5V 5 5 GND RTSAS DSR
ملخص المحتوى في الصفحة رقم 13
Quick Reference Guide PC/TS Adapter 9-pin subminiature D: 9-pin subminiature D: Signal: Signal: Shield Shield NC NC DCD 1 1 DCD RXD 2 2 RXD 3 3 TXD TXD 4 4 DTR DTR 5 5 GND GND DSR 6 6 DSR RTS 7 7 RTS 8 8 CTS CTS NC NC 9 9 RI RI Shield Shield Connector casing Connector casing Figure 1-8 RS232 Cable 6ES7 901-1BF00-0XA0 Warning ! The RS232 cable listed under Point 3 (Accessories) ensures that EMC requirements are met. This cannot be guaranteed if you use a different cable and you do so at your own
ملخص المحتوى في الصفحة رقم 14
PC/TS Adapter Quick Reference Guide 6.3 Pin Configuration The MPI/DP connector has the following pin configuration: 1 5 6 9 Figure 1-9 MPI/DP Connector Signals Pin Abbre- Description Input/ No. viation Output 1 NC Pin is unassigned - 2 M24V 24 V supply’s 0 V line, sup- Input plies adapter electronics via DC/DC converter (PC potential area) 3 LTG_B Data line B Input/out- put 4 RTSAS RTSAS Control signal for Input receive data current; the signal is active ‘1’ when the directly connected interfac
ملخص المحتوى في الصفحة رقم 15
Quick Reference Guide PC/TS Adapter Pin Abbre- Description Input/ No. viation Output 7 P24V 24V supply’s +24V line, Input supplies adapter electronics via DC/DC converter (PC potential area) 8 LTG_A Data line A Input/out- put 9 RTS_P Adapter’s RTS output Output G signal. The signal is ‘1’ when the adapter is transmitting. Shield On connector casing* * The shield is interconnected with the RS232 connector via the adapte casing’s shield. PC/TS Adapter A5E00078070-02 11
ملخص المحتوى في الصفحة رقم 16
PC/TS Adapter Quick Reference Guide The RS232 connector has the following pin assignments: 1 5 6 9 Figure 1-10 RS232 Connector (PC-compatible) Signals Pin Abbrevia- Description Input/ No. tion Output 1 DCD Data Carrier Detect Input 2 RXD Received Data Input 3 TXD Transmitted Data Output 4 DTR Data Terminal Ready Output 5 GND Reference potential (0V) for all RS232 signals (Signal Ground) 6 DSR Data Set Ready Input 7 RTS Request to Send Output 8 CTS Clear to Send Input 9 RI Ring Indicator Input Sh
ملخص المحتوى في الصفحة رقم 17
Quick Reference Guide PC/TS Adapter 6.4 Connection Procedures Start Switch PC/ modem off Establish cable connection on (see 6.2 “General”, RS232 side) RS232 side of the adapter (See 6.2 “General”, MPI/DP side) => Microprocessor in adapter starts Connect MPI/DP to work and switches the Power connector of LED to constant light after blinking adapter to three times (see also 6.6 “Function S7/M7/C7 system of the Power LED”) Switch PC/ modem on N 1st startup? Y Start “Set PG/PC interface” Install ada
ملخص المحتوى في الصفحة رقم 18
PC/TS Adapter Quick Reference Guide 6.5 Function and Operation of the Switch The switch is used for setting the transmission rate (19.2 kbps or 38.4 kbps) on the RS232 side of the adapter variant in direct connection. It has no function with modem connection. The transmission rate set with the switch must agree with the rate parameterized for the PC in “Set PG/PC interface”. Note A Transmission speed of 38,4 kbit/s is only possible using STEP 7 Version 3.1 or higher. Operating the switch: Cutout
ملخص المحتوى في الصفحة رقم 19
Quick Reference Guide PC/TS Adapter The switch is operated only infrequently and is recessed so that it cannot be operated inadvertently. See Figure 1-11 for the location of the switch. Both switch positions are labeled on the underside of the unit. To operate the switch, please use a ball-point pen (“retractable ball-point”) up to a diameter of 1.7 mm or a blunt instrument of the same size. Insert the extended point between the operating lever and the housing cutout on the side with the operati
ملخص المحتوى في الصفحة رقم 20
PC/TS Adapter Quick Reference Guide 7 Technical Specifications All required specifications are listed in the table below. Designation Technical Specifications PC adapter Order number PC Adapter 6ES7 972-0CA2x-0XA0 TS Adapter 6ES7 972-0CA3x-0XA0 Dimensions 108 mm x 50 mm x 24 mm (4.25 in. x 1.96 in. x 0.94 in.) (L x W x H) Weight Approx. 0.15 kilograms Interfaces to S7/M7/C7 RS485 (bis max. 1,5 Mbit/s) to PC RS232 (19.2 kbps / 38.4 kbps/can be set with switch) Supply voltage (V ) V 1 = 24 VDC
