ملخص المحتوى في الصفحة رقم 1
M30100T3-RPD-E
Emulation Pod for M16C/10 Series MCUs
User's Manual
Rev.1.00
March 1, 2004
REJ10J0426-0100Z
ملخص المحتوى في الصفحة رقم 2
Keep safety first in your circuit designs! • Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
ملخص المحتوى في الصفحة رقم 3
Preface The M30100T3-RPD-E is an emulation pod for the M16C/10 Series of Renesas 16-bit MCUs. It's used with a PC4701 emulator (excluding PC4701L and PC4700L) and a pod probe. This user's manual mainly describes specifications of emulation pod M30100T3-RPD-E and how to setup it. For details on the following products, which are used with the M30100T3-RPD-E, refer to each product's user's manual. • Pod probe: Each User's Manual • Emulator: PC4701 User's Manual • Emulator debugger: User's manual of
ملخص المحتوى في الصفحة رقم 4
Contents Chapter 1. Precautions for Safety ...........................................................................................7 1.1 Safety Symbols and Meanings ..............................................................................8 Chapter 2. Preparation ..........................................................................................................15 2.1 Package Components ..........................................................................................16 2.2
ملخص المحتوى في الصفحة رقم 5
Chapter 5. Specifications ......................................................................................................37 5.1 Specifications ......................................................................................................38 5.2 External Dimensions ...........................................................................................39 (1) External Dimensions of the Emulation Pod .............................................39 Chapter 6. Troubleshooting .......
ملخص المحتوى في الصفحة رقم 6
Terminology Some specific words used in this user's manual are defined as follows: Emulator system This means an emulator system built around the PC4701 emulator. The PC4701 emulator system is configured with an emulator main unit, emulation pod, pod probe, host machine and emulator debugger. Emulator main unit (Hereafter PC4701) This means a generic name for emulators for 8 and 16-bit MCUs. For details on specific models of PC4701, visit the Renesas Tools Homepage at http://www.renesas.com/en/t
ملخص المحتوى في الصفحة رقم 7
Chapter 1. Precautions for Safety This chapter describes precautions for using this product safely and properly. For precautions for the pod probe, emulator main unit and emulator debugger, refer to each user's manual included with your product. 1.1 Safety Symbols and Meanings ..................................................................................................... 8 WARNING Warning for Installation .....................................................................................
ملخص المحتوى في الصفحة رقم 8
Chapter 1. Precautions for Safety In both the User's Manual and on the product itself, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties. This chapter describes the precautions which should be taken in order to use this product safely and properly. Be sure to read this chapter before using this product. 1.1 Safety Symbols and Meanings If the requirements shown in the "WARNING" sentences are ignored,
ملخص المحتوى في الصفحة رقم 9
WARNING Warning for Installation: • Do not set this product in water or areas of high humidity. Make sure that the main unit does not get wet. Spilling water or some other liquid into the main unit can cause an unrepairable damage. Warnings for Use Environment: • The emulation pod is air-cooled with the ventilation slot. Therefore, do not block the ventilation slot. When heated to high temperatures, the emulation pod may not work properly. • This equipment is to be used in an environment with a
ملخص المحتوى في الصفحة رقم 10
IMPORTANT Note on Malfunctions in the PC4701 System: • If the emulator malfunctions because of interference like external noise, do the following to remedy the trouble. (1) Press the RESET button on the emulator front panel. (2) If normal operation is not restored after step (1), shut OFF power to the emulator once and then reactivate it. Notes on Downloading Firmware: • Before using this product for the first time, it is necessary to download the dedicated firmware (control software for the emu
ملخص المحتوى في الصفحة رقم 11
IMPORTANT Note on Clock Supply to the MCU: • Clock can be supplied to the evaluation MCU in one of the following two ways. This is determined by emulator debugger clock selection. (1) When Internal is selected: The clock generated by the oscillation circuit in the emulation pod is supplied to the evaluation MCU. The clock is continually supplied to the evaluation MCU regardless of "target system clock status" and "user program execution status". (2) When External is selected: Clock supply to the
ملخص المحتوى في الصفحة رقم 12
IMPORTANT Note on RESET* Input: • The reset input from the target system is accepted only while a user program is being executed (only while the RUN status LED on the PC4701's front panel is lit). Note on Operation When Not Executing the User Program: • With this product, bit 7 of processor mode register 1 (wait bit PM17) is forcibly set to "1" (with wait) when the user program is not executed (e.g. when the program is stopped or when run-time debugging is being performed). Therefore, if the ext
ملخص المحتوى في الصفحة رقم 13
IMPORTANT Notes on Software Breaks and Hardware Breaks: • The software break is a debugging function which breaks a program immediately before the system executes an instruction at a specified address. The instruction at the preset address will not be executed. • The hardware break is a debugging function which breaks a program by setting the detection of an execution of an instruction at a specified address as a break event. The program will break after the instruction at the specified address
ملخص المحتوى في الصفحة رقم 14
IMPORTANT Note on Differences between the Actual MCU and Emulator: •Operations of the emulator system differ from those of actual MCUs as listed below. (1) Reset condition Set the rise time (0.2 Vcc = 0.8 Vcc) to 1 µs or less. (2) Initial values of internal resource data at power-on (3) Internal memories (ROM and RAM) capacities, etc. With this emulator system, "INT" (emulation memory ON) is the default for mapping areas other than the SFR area (addresses 000h--3FFh). For this reason, the emulat
ملخص المحتوى في الصفحة رقم 15
Chapter 2. Preparation This chapter describes the package components, the system configuration and the preparation for using this product for the first time. 2.1 Package Components.................................................................................................................. 16 2.2 Other Tool Products Required for Development........................................................................ 16 2.3 Name of Each Part ........................................................
ملخص المحتوى في الصفحة رقم 16
Chapter 2. Preparation 2.1 Package Components The M30100T3-RPD-E package consists of the following items. When unpacking, check to see if your M30100T3-RPD-E contains all of these items. Table 2.1 Package components Item Quantity M30100T3-RPD-E emulation pod main unit 1 FLX120-RPD flexible cable for connecting PC4701 1 OSC-3 16MHz oscillator circuit board for main-clock (preinstalled) 1 OSC-2 oscillator circuit board (bare-board) 1 Hardware tool user registration FAX sheet (English) 1 Hardware t
ملخص المحتوى في الصفحة رقم 17
2.3 Name of Each Part (1) System Configuration Figure 2.1 System configuration (1) to (3) in Figure 2.1 are included in this product package. (1) Emulation pod main unit M30100T3-RPD-E This emulation pod contains emulation memory and circuit to feature the debugging functions. (2) Flexible cable FLX120-RPD This 120-pin flexible cable connects the PC4701 emulator and the emulation pod. (3) Flexible cable FLX64 This 64-pin flexible cable connects the emulation pod and the pod probe. (4) Pod probe
ملخص المحتوى في الصفحة رقم 18
2.4 When Using the Emulator for the First Time (1) Making the MCU File It is necessary to make an MCU file to use this product with the emulator debugger M3T-PD30. According to the MCU you use, change the contents of the MCU file. Make the MCU file following the description below using a text editor and store it in the "mcufiles" folder in the directory where the emulator debugger is installed. The MCU file contains information such as, SFR area, internal RAM area, internal ROM area, firmware fi
ملخص المحتوى في الصفحة رقم 19
(3) Downloading Firmware If you have purchased this emulation pod newly, it is necessary to download the firmware. The download procedure is given in Figure 2.2. Before attempting to download the firmware, check the emulator debugger is installed and the emulator is connected to the host machine. For more information, see each user's manual of the emulator debugger and the PC4701. See "3.4 Connecting the PC4701 Connect the PC4701 and this product and pod probe. and Emulation Pod" (page 27) and "
ملخص المحتوى في الصفحة رقم 20
MEMO ( 20 / 52 )
