ملخص المحتوى في الصفحة رقم 1
User’s Manual
Fast Ethernet CardBus
(MPC-200)
R
acsense
1
ملخص المحتوى في الصفحة رقم 2
Table of Contents Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Network Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Driver support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 3
Introduction Chapter 1 Introduction This manual describes how to operate the Fast Ethernet CardBus Card. The Fast Ethernet LAN PC Card is a Credit-card sized Ethernet Card which works with any comput- er, notebook, sub-notebook or Macintosh PowerBook G3 series, or Card Reader that sup- ports CardBus slots. CardBus is a function and performance extension of the PC Card (PCMCIA) stan- dards. The CardBus interface is a 32-bit wide and Bus-mastering allowable device. It enhanced the overall system t
ملخص المحتوى في الصفحة رقم 4
Introduction ¥ Bus Width: 32 bits ¥ Power: 3.3 V ¥ Temperature: 0ûC~60ûC/ 32ûF~140ûF (Std. Operating) ¥ Humidity: 10% to 90% ¥ Distance: 100m from Hub to Node ¥ Dimensions: 86mm x 54mm x 5 mm Installing the Fast Ethernet CardBus Card You will be installing the Fast Ethernet CardBus Card in your computer. If you are having trouble locating the slot, refer to the user's manual of your computer or consult the manufacture of your computer. Gently slide the PC Card into the CardBus PC Card slot. Make
ملخص المحتوى في الصفحة رقم 5
Getting Started Chapter 2 Getting Started Installing the Fast Ethernet CardBus Card You will be installing the Fast Ethernet CardBus Card in CardBus slot of your computer. If you have trouble locating the slot, please refer to your computer's user manual or consult the dealer of your computer. Follow the procedure below to install the Fast Ethernet CardBus Card. 1. Turn off the host computer. 2. With the card's 68 pin connector facing the PCMCIA CardBus slot, gently slide the PC Card into the Ca
ملخص المحتوى في الصفحة رقم 6
Getting Started LED Indicators ¥ 100 LED: This LED is used to indicate the Ethernet speed: The green light indicates a connection with a 100BASE-TX Fast Ethernet network. ¥ Link/Act LED: This LED is used to indicate the network activity. It is blinking when the PC Card is transmitting or receiving packets from network. It is also lit when indicating a Link to a network. README There is one file named Readme on driver diskette which provides the information about this Driver Diskette's contents
ملخص المحتوى في الصفحة رقم 7
Chapter 3 Driver Installation for Mac OS Chapter 3 Driver Installation for Mac OS System Requirements ¥ Mac OS version 8.1 or above. ¥ Macintosh G3 PowerBook Series. ¥ Card and Socket Service 3.0. ¥ Open Transport 1.3 or above Installation Before your computer system can recognize your Fast Ethernet CardBus Card, it is necessary to run some software to enable it. This section gives a brief overview of the installation process. Software Installation 1. Make sure that the system extensions are l
ملخص المحتوى في الصفحة رقم 8
Chapter 3 Driver Installation for Mac OS 4. Click the Install button. The Installer will install the appropriate driver to your com- puter. 5. Click the Restart button when installation is completed. AppleTalk Setup ¥ Open the AppleTalk control panel ¥ Select FastEther Card from the pop-up menu. Optional: The Current Zone pop-up menu will be active if zones are available. 6
ملخص المحتوى في الصفحة رقم 9
Chapter 3 Driver Installation for Mac OS ¥ Close the control panel when you have finished. ¥ To confirm the change of network connections, click OK. TCP/IP Setup ¥ Open the TCP/IP control panel. ¥ Select FastEther Card from the pop-up menu. . ¥ Set up TCP/IP configuration according to the situation of your network environment. ¥ Close the control panel when you have finished. ¥ To confirm the change of network connections, click OK. Ejecting the FastEther Card ¥ Open the AppleTalk control panel
ملخص المحتوى في الصفحة رقم 10
Chapter 3 Driver Installation for Mac OS ¥ Drag the FastEther Card icon that appears on the desktop to the Trash. ¥ Then the FastEther Card will eject automatically. 8
ملخص المحتوى في الصفحة رقم 11
Specification Appendix A Specifications ¥ Network standard: 10Mbps IEEE 802.3 10BASE-T Ethernet 100Mbps IEEE 802.3u 100BASE-TX Fast Ethernet ¥ Type II PCMCIA, Hot Plug-and-Play Fast Ethernet CardBus Card, supports Full Duplex 10BASE-T and 100BASE-TX communication ¥ Complies with 32-bit PCI Card Bus specification. ¥ For Windows 3.x and Windows 95, Windows 98 ,and Windows NT operation sys- tem. ¥ Support for Network and Communication Device Class OnNow requirements for Microsoft PC97 and PC98 spec
ملخص المحتوى في الصفحة رقم 12
Assignment Appendix B Pin Assignment RJ-45 connector The RJ-45 connector is used to connect with a hub or switch, RJ-45 regular ports can be attached to any devices which use a standard network interface (e.g., a workstation, server, bridge or router). RJ-45 up-link ports can be cascaded to a station port on similar networking devices (e.g., another switch or hub). Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100½ Category 3, 4 or 5 cable for 10 M
ملخص المحتوى في الصفحة رقم 13
Copyright Copyright © 1998 by this company. All right reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work ( such as translation or transformation ) without permission from Macsense Connectivity, Inc. . Macsense Connectivity, Inc. reserves the right to revise this documentation and to make changes in content sometimes without obligation among Macsense Connectivity, Inc. to provide notification of such revision or change. FCC War
