ملخص المحتوى في الصفحة رقم 1
PCMCIA 10Base-T/2
Ethernet Adapter
User Manual English
LINDY No. 70982
www.LINDY.com
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (JUNE 2004)
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Contents INTRODUCTION ......................................................................................................................... 2 FEATURES.................................................................................................................................. 2 PACKAGE CONTENTS .............................................................................................................. 2 INSTALLING THE ETHERNET CARD.......................................................
ملخص المحتوى في الصفحة رقم 4
User Manual Introduction Thank you for purchasing the LINDY PCMCIA 10Base-T/2 Ethernet Card. This Ethernet card supports 10Base-2 and 10Base-T networks. The card is NE2000 compatible and supports “Hot Swap” insertion and removal. Features Bus Type: 16 Bit PCMCIA Complies with IEEE802.3 standard (10Base-T/2) NE2000 Ethernet Adapter compatible Complies with PCMCIA release 2.1 and JEIDA 4.x standards Software configurable “Hot swap” insertion and removal LED diagnostic and activity indicator
ملخص المحتوى في الصفحة رقم 5
User Manual Installing the Ethernet Card The LINDY PCMCIA 10Base-T/2 Ethernet Card installs into a spare Type II or III PCMCIA slot in your computer. If you are having trouble locating this slot, refer to your computer’s user manual or consult the manufacturer. Gently slide the card into the PCMCIA slot. Make sure the card is firmly seated in the socket. Now you are ready to setup and install your communication software, as detailed in the following section. README.TXT File On the driver disk is
ملخص المحتوى في الصفحة رقم 6
User Manual For Card and Socket Services device drivers in the CONFIG.SYS file, please add the ENABLE.EXE. The default parameters for the ENABLE.EXE program are INT=5, PORT=300 and MEM=D400. The following examples describe which instructions are needed for the popular Card and Socket Services providers. Phoenix PCM+ V3.0 DEVICE=C:\PCM3\CNFIGNAM.EXE /SETUP-DEFAULTS DEVICE=C:\PCM3\PCMSS.EXE DEVICE=C:\PCM3\PCMCS.EXE DEVICE=C:\PCM3\PCMRMAN.SYS DEVICE=C:\PCM3\PCMSCD.EXE DEVICE=ENABLE.EXE SystemSoft C
ملخص المحتوى في الصفحة رقم 7
User Manual IBM Thinkpad Socket and Card Services V2.12 DEVICE=C\EMM386.EXE NOEMS I=B000-B7FF X=C800-CFFF X=D000-DFFF DEVICE=C:\THINKPAD\IBMDSS01.SYS /D DEVICE=C:\THINKPAD\IBMDOSCS.SYS DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-DFFF DEVICE=C:\THINKPAD\$ICPMDOS.SYS DEVICE=ENABLE.EXE Netware DOS ODI Driver The DOS ODI driver for Netware 3.x and 4.x network operating systems is located in the ODI directory of the driver diskette. The filename is CARDODI.COM. To install this ODI driver, there is a bat
ملخص المحتوى في الصفحة رقم 8
User Manual Setup for Windows 95/98 1. Make sure the PC is powered on and booted into Windows. 2. Insert the Ethernet adapter into the PCMCIA slot in your PC. The system will display the "Add New Hardware Wizard" dialog box. Insert the driver diskette into the floppy drive and then click "Next". 3. Select "Search for the Best Driver for your device (Recommended) ". Click "Next" button. 6
ملخص المحتوى في الصفحة رقم 9
User Manual 4. Select "Floppy disk drives" (or select "Specify a location" and type "A:\WIN98" in the location). Click "Next" 5. After Windows finds the driver - "PCMCIA NE2000 Compatible Ethernet Adapter", click "Next". 7
ملخص المحتوى في الصفحة رقم 10
User Manual 6. After the driver is found, Windows will begin to copy all the necessary files. If Windows tries to copy the "PCMCARD.SYS" file, input "A:\WIN98" to specify the location of this file. 7. Windows may request you to "Insert Windows 98 CD-ROM into the drive selected, and click OK". Follow the instructions and insert your Windows CD-ROM or disks as needed, and then click "OK". 8. When Windows finishes the installation, the "PCMCIA NE2000 Compatible Ethernet Adapter", message box will b
ملخص المحتوى في الصفحة رقم 11
User Manual Setup for Windows NT Follow the procedure below to get up and running. 1. Insert the Ethernet Card in your computer 2. Start the computer 3. Double click the "Control Panel/Network" section. Select "Adapters" and click the "Add" button. 4. In the "Select Network Adapter" dialog box, select the "Have Disk" option. 9
ملخص المحتوى في الصفحة رقم 12
User Manual 5. An "Insert Disk" box is displayed. Insert the driver disk and type "A:\WINNT". 6. "NE2000 PCMCIA ETHERNET CARD" is displayed in the "Select OEM Option" dialog box. Click "OK". 7. Select the free IRQ, I/O Port Address and press "OK". You must select hardware bus if the system contains more than one hardware bus. Type "PCMCIA" and Number "0", then press "OK". 10
ملخص المحتوى في الصفحة رقم 13
User Manual 8. Go back to "Network" and select "Bindings". Click the "Close" button to enable the network function. 9. Ask your Windows NT Server administrator to set the IP Address. 10. Click "OK" to finish the network settings. A "Network Setting Change" box is displayed. Click "Yes" to restart your computer. 11
ملخص المحتوى في الصفحة رقم 14
User Manual Setup for Windows 2000 1. Make sure your PC is powered on and booted into Windows. 2. Insert the Ethernet Card into a spare PCMCIA slot in your PC. The system will display the "Found New Hardware Wizard" dialog box. Insert the driver diskette into floppy drive and click "Next". 3. Select "Search for a suitable driver for my device (Recommended)", and click "Next". 12
ملخص المحتوى في الصفحة رقم 15
User Manual 4. Select "Floppy disk drives" (or select "Specify a location" and type "A:\WIN2000" in the location). 5. After Windows finds the driver, the following prompt will appear: "PCMCIA LNT-10TN". Click "Next"; the driver then installs itself. 6. When Windows finishes the installation, the "PCMCIA NE2000 Compatible Ethernet Adapter" message box will be displayed. Click "Next" to continue. 7. Restart the computer. After the computer has restarted the network function will be ready. 13
ملخص المحتوى في الصفحة رقم 16
User Manual Setup for Windows ME 1. Make sure your PC is powered on and booted into Windows. 2. Insert the Ethernet Card into a spare PCMCIA slot in your PC. The "Add New Hardware Wizard" will be displayed. Select "Automatic search for a better driver", and insert the driver disk. Click "Next" The system will display the "Found New Hardware Wizard" dialog box. Insert the driver diskette into floppy drive and click "Next". 3. Windows ME will search and automatically install the driver files. 4. A
ملخص المحتوى في الصفحة رقم 17
User Manual Setup for Windows XP 1. Make sure your PC is powered on and booted into Windows. 2. Insert the Ethernet Card into a spare PCMCIA slot in your PC. Windows XP will recognize the device. The "Found New Hardware Wizard" will be displayed. Select "Install the software automatically (Recommended) " and insert the driver disk and click "Next". 3. Select the XP driver from the and click "Next". 15
ملخص المحتوى في الصفحة رقم 18
User Manual 4. The system will state that the driver has not passed Windows logo testing. Click "Continue Anyway". Windows will automatically copy the relevant driver files. 5. After copying the driver files, installation is complete. Click "Finish". The network function is now ready. 16
ملخص المحتوى في الصفحة رقم 19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations.
