ملخص المحتوى في الصفحة رقم 1
MT8850A / MT8852A Bluetooth Test Set
Operation Manual
For MT8850A and MT8852A software release 2.30
Originated by Anritsu Ltd, EMD, Stevenage, U.K. P/N: 13000-000109
REVISION: G
CREATED June 2003
COPYRIGHT 2003
ANRITSU
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Warranty The Anritsu product(s) listed on the title page is (are) warranted against defects in materials and workmanship for one year from the date of shipment. Anritsu’s obligation covers repairing or replacing products that prove to be defective during the warranty period. Buyers shall prepay transportation charges for equipment returned to Anritsu for warranty repairs. Obligation is limited to the original purchaser. Anritsu is not liable for consequential damages. Limitation of W
ملخص المحتوى في الصفحة رقم 4
Safety Symbols To prevent the risk of any personnel injury or loss related to equipment malfunction, Anritsu Company uses the following symbols to indicate safety-related information. For your own safety, please read this information carefully BEFORE operating the equipment. Symbols Used in This Manual Danger Indicates a very dangerous procedure that could result in serious injury or death if not performed properly. Warning Indicates a hazardous procedure that could result in serious
ملخص المحتوى في الصفحة رقم 5
For Safety Always refer to the operation manual when working near locations at which the alert mark, shown on the left, is attached. If operation is performed without heeding the advice in the operation manual, there is a risk of personal injury. In addition, the equipment performance may be reduced. Moreover, this alert mark is sometimes used with other marks and descriptions indicating other dangers. When supplying AC power to this equipment, connect the accessory 3-pin power
ملخص المحتوى في الصفحة رقم 6
Declaration of Conformity iv 13000-000109 June 2003
ملخص المحتوى في الصفحة رقم 7
13000-000109 v June 2003
ملخص المحتوى في الصفحة رقم 8
Table of Contents Warranty .................................................................................................................. i Limitation of Warranty .............................................................................................. i Trademark Acknowledgments ................................................................................. i Notice about Documentation.................................................................................... i Safety S
ملخص المحتوى في الصفحة رقم 9
Chapter 4. Connections ............................................................................................ 4-1 Introduction ................................................................................................................ 4-1 Front Panel Connectors ............................................................................................. 4-1 Rear Panel Connectors.............................................................................................. 4-1 Cha
ملخص المحتوى في الصفحة رقم 10
Setting the modulation index.............................................................................. 7-17 Setting Up the Link Timeout............................................................................... 7-17 Setting Up the IF Bandwidth Filter ..................................................................... 7-17 Setting Up Test Script Operation.............................................................................. 7-18 System features ............................
ملخص المحتوى في الصفحة رقم 11
Power Control Test Results (standard and null packet modes) ........................ 8-42 Initial Carrier Test Results ................................................................................. 8-43 Carrier Drift Test Results ................................................................................... 8-44 Single Slot Sensitivity Results ........................................................................... 8-46 Multi Sensitivity Test Results.............................
ملخص المحتوى في الصفحة رقم 12
Audio Specifications (MT8852 only)........................................................................ C-12 Frequency Standard................................................................................................ C-12 Rear Panel Connectors ........................................................................................... C-12 GPIB........................................................................................................................ C-12 RS 232 ......
ملخص المحتوى في الصفحة رقم 13
Chapter 1. General Information Scope of this Manual This manual provides installation and operation information for the following two units: • MT8850A Bluetooth Test Set • MT8852A Bluetooth Test Set. All information in this manual applies equally to both the MT8850A and the MT8852A unless otherwise stated, and is most cases this is signified by the use of “MT8850A/MT8852A”. The screen images provided in the procedural explanations have been taken from the MT8850A unit, although these
ملخص المحتوى في الصفحة رقم 14
MT8850A / MT8852A Bluetooth Test Set General Information 3.5 mm jack plug x 3 (MT8852A only) Options and Accessories MT8850A-01 Rack Mount, single instrument MT8850A-03 Rack Mount, side-by-side MT8850A-06 Rear Mount RF and EUT connectors MT8850A 10 Bluetooth antenna and adapter MT8852A-12 Headset Profile Emulator Software MT8850A-20 Spare EUT/RS232 cable MT8850A-21 Spare EUT/USB cable MT8850A-30 Extra Operation and Programming Manual D41310 Soft Carry Case with shoulder strap 2300-
ملخص المحتوى في الصفحة رقم 15
Chapter 2. Product Overview About Bluetooth Bluetooth wireless technology will simplify connections between everyday appliances such as mobile phones, PCs and PDAs. Bluetooth will not be confined to the office - home applications will include portable music players, digital cameras, video recorders and children’s toys. In future, Bluetooth technology will be found in the automotive, avionics and industrial controls markets. Bluetooth technology will provide individuals with a personal net
ملخص المحتوى في الصفحة رقم 16
MT8850A / MT8852A Bluetooth Test Set Product Overview MT8850A/MT8852A Features • Three test modes • Standard mode in which the MT8850A/MT8852A uses full Test Mode signalling and all the defined test controls to test the EUT in the fastest and most efficient way possible. • Single payload mode in which Test Mode signalling is performed in a very restricted manner. The customer can define the packet length, packet payload, select loopback or TX mode and hopping on or off. • Null packet
ملخص المحتوى في الصفحة رقم 17
Product Overview MT8850A / MT8852A Bluetooth Test Set • Editing tests Define your own test scripts to customize the test measurements to your specific requirements. Each test can be enabled or disabled and within any test, parameters such as hopping can be enabled or disabled, the number of measured packets defined, and the specific frequencies of testing set up. • Making a link The BT address can be acquired by entering it manually at the keyboard, by performing an inquiry, or by mean
ملخص المحتوى في الصفحة رقم 18
MT8850A / MT8852A Bluetooth Test Set Product Overview 2-4 13000-000109 The MT8850A/MT8852A June 2003
ملخص المحتوى في الصفحة رقم 19
Chapter 3. Installation Introduction This chapter provides information for the initial inspection and preparation for use of the MT8850A/MT8852A Bluetooth Test Set. Shipping and storage information is also included. Initial Inspection Inspect the shipping container for damage. If the container or cushioning material is damaged, retain until the contents of the shipment have been checked against the packing list and the instrument has been checked for mechanical and electrical operation.
ملخص المحتوى في الصفحة رقم 20
MT8850A / MT8852A Bluetooth Test Set Installation Environmental Requirements The MT8850A/MT8852A is designed to operate within the temperature range of 5 to 40° C (41 to 104° F) with a maximum humidity of 90% at 40° C (104° F), non-condensing. Full accuracy is specified at 5 to 35° C (23 to 95° F). Although not recommended, operation in temperatures to –20°C (–4° F) is possible. At these temperatures, however, the liquid crystal display may exhibit excessively slow response. The instru
