ملخص المحتوى في الصفحة رقم 1
WAVE 2-Way Wireless Accessories and Adapters
for Touch Panels
Instruction Manual
Control Panel Accessories
ملخص المحتوى في الصفحة رقم 2
Limited Warranty and Disclaimer Panja Inc. warrants its products to be free from defects in material and workmanship under normal use for a period of three years from date of purchase from Panja, In- corporated, with the following exceptions. Electroluminescent and LCD control pan- els are warranted for a period of three years, except for the display and touch over- lay components which are warranted for a period of one year. Disk drive mecha- nisms, pan/tilt heads, power supplies, modificatio
ملخص المحتوى في الصفحة رقم 3
Table of Contents Introduction ............................................................................ 1 Overview 1 Features 2 What’s in this Manual 2 What’s New 3 AXR-WAVES 3 WAV-PK 3 WAV-PKM 3 WAV-LNK WaveLink 4 WAV-PM WaveLink power module 4 Related Instruction Manuals 4 Sample Product Application 5 AXR-WAVES 5 Front panel 5 Rear panel 7 WAV-PK 7 Front panel 7 Rear panel 8 WAV-PKM 8 Front panel 8 Rear panel 9 WAV-LNK WaveLink 9 Front panel 10 Rear panel 10 Option
ملخص المحتوى في الصفحة رقم 4
AXR-WAVES (or WAV-LNK) Group ID DIP Switch 18 WAV-PK Group ID DIP switch 19 WAV-PKM Group ID DIP switch 20 Battery Charging 20 WAV-PM WaveLink Power Module 21 Installation............................................................................ 23 Overview 23 Installing the Control System 23 Wiring the AXR-WAVES 24 Guidelines 24 Preparing captive wires 25 Connecting AXlink for data and power 25 Installing the WAV-PK 26 WAV-PK Battery Replacement 27 Installing the WAV-PKM 28 WAV
ملخص المحتوى في الصفحة رقم 5
Introduction Overview The AXR-WAVES Wireless AXlink Virtual Emulator Server (Figure 1) is a 2-way Radio Frequency (RF) device employing spread spectrum communications. A single AXR-WAVES can communicate with up to 16 wireless TiltScreen touch panels equipped with WAV-PK or WAV-PKM Wireless Power Packs. The WAV-PK and WAV-PKM are designed to enable 2-way wireless mobility of full-sized and mini- touch panels, thus eliminating the need for permanent installation of a touch panel. Refer to t
ملخص المحتوى في الصفحة رقم 6
Additionally, the WAV-LNK WaveLink transceiver (Figure 2) may be used in con- junction with one or more WAV-PM modules when a UniMount or rack mounted touch panel is used in a remote, wireless application. The WAV-LNK is ideal for Un- iMount touch panels mounted in podiums or lecterns where cabling is of concern. Figure 2 WAV-LNK transceiver Features The major features for the AXR-WAVES, WAV-LNK, WAV-PK, and WAV-PKM are described in the following paragraphs. Additionally, information for
ملخص المحتوى في الصفحة رقم 7
What’s New Updates to this manual include: • Battery usage, safety warnings, and caution information • Updated technical support information All other revisions are identified by vertical margin bars as shown adjacent to this paragraph. AXR-WAVES AXR-WAVES features include: • 2-way RF communications with up to 16 TiltScreen touch panels equipped with wireless power packs • 2-way communication via a 2.4 GHz frequency hopping, spread spectrum technology WAV-PK WAV-PK features include
ملخص المحتوى في الصفحة رقم 8
• Rechargeable lead-acid battery (WAV-PKM Mini-WavePack Battery) Note • Lithium battery maintains the flash RAM The WAV-PKM contains two small lithium batteries that will WAV-LNK WaveLink last approximately 5 years. The batteries are not user re- The WAV-LNK WaveLink transceiver features include: placeable and the WAV-PKM must be returned to Panja for • 2-way RF spread-spectrum communications with an AXR-WAVES server. battery replacement. • Operates from an external power supply and
ملخص المحتوى في الصفحة رقم 9
Sample Product Application The AXR-WAVES connects to a Central Controller and communicates with a wide variety of touch panels. The WAV-PK and WAV-PKM power packs connect to full- sized and mini-touch panels to provide mobility and communications with an AXR- WAVES. Figure 3 shows a sample control system using an AXR-WAVES communi- cations configuration. AXT-CP AXT-CA Figure 3 AXT-MCA Sample Central Controller and AXR-WAVES communica- (connects to tions application rear panel) Power WAV-P
ملخص المحتوى في الصفحة رقم 10
Figure 4 AXR-WAVES front panel • AXlink—Green LED that blinks when there is AXlink communication activ- ity. The green AXlink LED indicates the following power and data activity: One blink per second: Power is active and AXlink data communication is functional. — Full on: Power is active and AXlink data communication is not func- tional. • GROUP ADDRESS—Eight-position DIP switch sets the group address (0 through 255). • GROUP ID—Four-position DIP switch sets the control group identific
ملخص المحتوى في الصفحة رقم 11
Rear panel The rear panel has an RF antenna and a 4-pin AXlink bus connector. Figure 5 shows the AXR-WAVES rear panel. Figure 5 AXR-WAVES rear panel • ANTENNA—Right-angle, flexible, bi-directional RF antenna. • AXlink—Four-pin (male) connector connects to the Central Controller to re- ceive AXlink control data and 12 VDC power. WAV-PK The WAV-PK full-sized TiltScreen touch panel controls and indicators are described in the following paragraphs. Front panel The front of the WAV-PK po
ملخص المحتوى في الصفحة رقم 12
Figure 6 WAV-PK power pack front panel and connector Rear panel The WAV-PK rear panel provides a barrel power (plug-in) connector for operating or recharging of the unit. There is also a wake-up switch located in the center-rear of the WAV-PK. Figure 7 shows the rear of the unit and the power connector. WAV-BP Figure 7 Battery clip battery WAV-PK rear panel Group ID switch ON 1 2 3 4 Wake-up switch Power supply connector WAV-PKM The WAV-PKM Mini-TiltScreen touch panel contr
ملخص المحتوى في الصفحة رقم 13
Figure 8 WAV-PKM front panel Rear panel The WAV-PKM rear panel provides a power connector for operating or recharging of the unit. Figure 9 shows the rear of the unit and the power connector. Figure 9 Power supply connection WAV-PKM rear panel WAV-LNK WaveLink The WAV-LNK WaveLink transceiver provides an interface for up to 16 touch pan- els or similar AXlink type devices. The WAV-LNK communicates with the AXR- WAVES and allows connecting devices requiring AXlink communications. T
ملخص المحتوى في الصفحة رقم 14
Front panel Figure 10 shows the front panel for the WAV-LNK and its switches and indicators are described below. Figure 10 WAV-LNK front panel • AXlink—This LED lights when an active AXlink connection is established. • GROUP ADDRESS—Eight-position DIP switch sets the group address (0 through 255). • GROUP ID—Four-position DIP switch sets the control group identification address (0 through 15). • STATUS—Red LED flashes during normal operation. • RX—Red LED lights when the WAV-LNK rec
ملخص المحتوى في الصفحة رقم 15
Figure 11 WAV-LNK rear panel 12VDC + - PWR Optional WAV-PM WaveLink Power Module The WAV-PM WaveLink Power Module provides additional wireless backup power Note to a WaveLink device. WAV-PMs can be daisy-chained to provide 12 VDC at up to The WAV-PM WaveLink 10 A. The following paragraphs identify and define controls and indicators for the Power Module will only accept optional WAV-PM WaveLink Power Module. only the full-sized WAV-BP batteries. Front panel Figure 12 shows the W
ملخص المحتوى في الصفحة رقم 16
• Empty/Full gauge—The BATTERY indicator gauge (empty-full) provides a Note visual indication of the charge level of the battery currently being used. If While a battery is charging, the the battery's charge is high, all left-to-right indicator lamps will be lit. Empty/Full indicator does not show a valid reading. • Test—Pressing the TEST button displays an indication of the current bat- tery's charge level on the front panel’s Empty/Full gauge. • Charging—The CHARGING indicator lights
ملخص المحتوى في الصفحة رقم 17
Power management The Wave Packs incorporate advanced power management schemes that reduce overall power consumption. Power management is software-controlled by the indi- vidual touch panel program. The user tells the WavePack when to go into power conservation mode (sleep mode). Pressing the rear-mounted WAV-PK wake-up switch activates the WavePack. The WAV-PK physically provides a wake-up switch on its rear panel. The WAV- PKM wakes up when someone touches the touch panel screen. Refer to
ملخص المحتوى في الصفحة رقم 18
Safe handling and usage of the battery To prevent deterioration or damage to the battery: • Do not use battery to power equipment other than the WAV-PK or WAV- PKM. • Do not drop or subject the battery to strong physical shock. • Do not use the battery below -10°C (15°F) or above +40°C (105°F). If the temperature exceeds this upper limit, a safety device automatically prevents operation of the battery. Standard Power Supply The standard power supply furnished with the WAV-PK and WAV-PKM
ملخص المحتوى في الصفحة رقم 19
Optional WAV-CHG Fast-Cycle Battery Charger The WAV-CHG Fast-Cycle Battery Charger is shown in Figure 17. The charger will charge two batteries simultaneously. Refer to the Battery Charging subsection of this manual. The charger provides a fast-cycle, 4-hour, full-charge capability. Figure 17 LED charging indicator Optional battery charging holder and power supply CHARGE POWER CHARGE Power Supply Power supply connector Battery holder with Fast-Cycle circuitry WAVE 2-Way Wireless
ملخص المحتوى في الصفحة رقم 20
16 Introduction WAVE 2-Way Wireless Accessories and Adapters for Touch Panels
