ملخص المحتوى في الصفحة رقم 1
300N Draft 802.11n Wireless PCI Adapter
Model # AWLH6080
User’s Manual
Rev. 1.0
ملخص المحتوى في الصفحة رقم 2
Table of Contents 1. Introduction .................................................................................................................3 1.1 Package Contents ................................................................................................. 3 1.2 Features ................................................................................................................ 3 2. Installation ................................................................................
ملخص المحتوى في الصفحة رقم 3
1. Introduction Congratulations on your purchase of the 300N Draft 802.11n Wireless PCI Adapter. The 300N PCI Adapter provides wireless data rate of up to 300 Mbps* when used with other AirLink101® 300N wireless products. The high bandwidth combined with extended wireless coverage delivers fast and reliable connection for all of your networking applications. A full range of security features such as WEP, WPA-PSK, and WPA2-PSK provide the highest level of wireless network security. The
ملخص المحتوى في الصفحة رقم 4
2. Installation 2.1 Install Driver & Utility This section provides instructions on how to install the 300N Draft 802.11n Wireless PCI Adapter. The driver is installed along with the utility. Note: Be sure to power off your computer before inserting the Cardbus adapter. Step 1 Insert the PCI adapter into an available PCI slot and turn on your computer. Step 2 After turning on the computer, Windows will launch the Found New Hardware Wizard. The Found New Hardware Wizard appears
ملخص المحتوى في الصفحة رقم 5
Note: If the Autorun screen doesn’t appear automatically, or if you get a blank white screen, go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK. Windows Vista users: At this point, you may get a warning message like the one below. Make sure that you click Allow to continue with the installation. 5
ملخص المحتوى في الصفحة رقم 6
Step 4 Click Next at the welcome screen. Step 5 Click Next to accept the default destination folder. 6
ملخص المحتوى في الصفحة رقم 7
Step 6 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). 7
ملخص المحتوى في الصفحة رقم 8
For Windows Vista, click the Install this driver software anyway button when the security warning appears. Step 7 Click Yes, I want to restart my computer now and then Finish to restart your computer. 8
ملخص المحتوى في الصفحة رقم 9
Step 8 After the computer is restarted, Windows will ask to connect to Windows Update, select No, not this time and click Next. If this screen does not appear, you can skip to section 2.2. Step 9 Select Install the software automatically and click Next. 9
ملخص المحتوى في الصفحة رقم 10
Step 10 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). For Windows Vista, click the Install this driver software anyway button when the security warning appears. 10
ملخص المحتوى في الصفحة رقم 11
Step 11 Click Finish. 11
ملخص المحتوى في الصفحة رقم 12
2.2 Verify Driver Installation To verify if the driver has been installed successfully, please perform the following steps. Step 1 Right-click on My Computer from your desktop and select Properties. Step 2 If you are using Windows XP/2000 select the Hardware tab, then click on Device Manager. If you are using Windows Vista, click on the device manager link on the left side of the screen. 12
ملخص المحتوى في الصفحة رقم 13
Step 3 Expand Network adapters from the list and verify that AirLink101 300N Wireless PCI Adapter is listed and no yellow question mark is beside it. If AirLink101 300N Wireless PCI Adapter is not listed, or you see a yellow question mark beside it, you will need to reinstall the driver. 13
ملخص المحتوى في الصفحة رقم 14
3. Configuring the Adapter This section describes how to connect your wireless adapter to a wireless network. Note to Windows XP Users: You must disable the Wireless Zero Configuration Utility in order to use the bundled Wireless Utility. Please follow the steps below to disable XP’s wireless utility. Windows Vista users can skip the following instructions and go to Step 1 Double-click on the Wireless Network Connection Icon in the system tray and then click on Properties or A
ملخص المحتوى في الصفحة رقم 15
Step 1 To open the utility, double click on the Wireless Monitor icon in the system tray at the bottom right-hand corner of your screen. Step 2 Go to the AP List tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Connect. 15
ملخص المحتوى في الصفحة رقم 16
If the network you are attempting to connect to is configured for encryption, you will see an orange lock icon next to the network. 16
ملخص المحتوى في الصفحة رقم 17
When you click on it and click connect, a box will pop up requesting the wireless encryption key for the router. Enter the encryption key into the box and click OK. 17
ملخص المحتوى في الصفحة رقم 18
Step 3 You should now be connected. You should see “Connected” in the top, right hand corner, and there will be a blue circle around the antenna icon next to the network name. Troubleshooting: If you are experiencing problems with the connection (unable to connect, low signal strength, slow connection speed, not working, unstable wireless connection) you will want to tune your router’s signal by changing channels on the router or adjusting the antenna direction. You do not need
ملخص المحتوى في الصفحة رقم 19
4. Wireless Monitor This section describes the various functions of the Wireless Monitor that you can configure, including the settings of wireless encryption. 4.1 Wireless Information The Wireless Information box at the top of the window provides you with the status of the current connection, including signal, network name (SSID), IP Address and router channel. 19
ملخص المحتوى في الصفحة رقم 20
4.2 AP List The AP List tab displays all the available wireless networks detected by the Wireless Adapter. Simply select the wireless network you wish to connect to and click Connect. If you have created multiple profiles, you can use the profile chooser at the bottom to select the specific profile you want to use. Then click Activate to enable that profile. 20
